Search NASA⌕ Search

Engineering topics

Repins, I

Publications and source records attributed to Repins, I.

Phase identification and control of thin films deposited by co-evaporation of elemental Cu, Zn, Sn, and Se

Kesterite thin films [(i.e., Cu{sub 2}ZnSn(S,Se){sub 4} and related alloys] have been the subject of recent interest for use as an absorber layer for thin film photovoltaics due to their high absorption coefficient (>10{sup 4} cm{sup -1}), their similarity to successful chalcopyrites (like CuInxGa{sub 1-x}Se{sub 2}) in structure, and their earth-abundance. The process window for growing a single-phase kesterite film is narrow. In this work, we have documented, for our 9.15%-efficient kesterite co-evaporation process, (1) how appearance of certain undesirable phases are controlled via choice of processing conditions, (2) several techniques for identification of phases in these films with resolution adequate to discern changes that are important to device performance, and (3) reference measurements for those performing such phase identification. Data from x-ray diffraction, x-ray fluorescence, Raman scattering, scanning electron microscopy, energy dispersive spectroscopy, and current-voltage characterization are presented.

36 MATERIALS SCIENCE↗

How Grain Boundaries in Cu(In,Ga)Se2 Thin Films are Charged: Revisit

Potential measurements on Cu(In,Ga)Se{sub 2} thin films using scanning Kelvin probe force microscopy have been reported extensively to address grain-boundary (GB) recombination by examining GB charging. However, the results are highly inconsistent. We revisit this issue by measuring high- and low-quality wide-bandgap films and using a complementary method of scanning capacitance microscopy. Our results show consistent positively charged GBs in our high-quality films with minimal surface defects, except for the {Sigma}3[112] GBs, which are charge neutral. We discuss possible artifacts due to surface defects when examining the GB charging and the role of GBs in the device performance.

14 SOLAR ENERGY↗

Determination of Grain Boundary Charging in Cu(In,Ga)Se2 Thin Films: Preprint

Surface potential mapping of Cu(In,Ga)Se2 (CIGS) thin films using scanning Kelvin probe force microscopy (SKPFM) aims to understand the minority-carrier recombination at the grain boundaries (GBs) of this polycrystalline material by examining GB charging, which has resulted in a number of publications. However, the reported results are highly inconsistent. In this paper, we report on thepotential mapping by measuring wide-bandgap or high-Ga-content films and by using a complementary atomic force microscopy-based electrical technique of scanning capacitance microscopy (SCM). The results demonstrate consistent, positively charged GBs on our high-quality films with minimal surface defects/charges. The potential image taken on a low-quality film with a 1.2-eV bandgap showssignificantly degraded potential contrast on the GBs and degraded potential uniformity on grain surfaces, resulting from the surface defects/charges of the low-quality film. In contrast, the potential image on an improved high-quality film with the same wide bandgap shows significantly improved GB potential contrast and surface potential uniformity, indicating that the effect of surface defectsis critical when examining GB charging using surface potential data. In addition, we discuss the effect of the SKPFM setup on the validity of potential measurement, to exclude possible artifacts due to improper SKPFM setups. The SKPFM results were corroborated by using SCM measurements on the films with a CdS buffer layer. The SCM image shows clear GB contrast, indicating different electricalimpedance on the GB from the grain surface. Further, we found that the GB contrast disappeared when the CdS window layer was deposited after the CIGS film was exposed extensively to ambient, which was caused by the creation of CIGS surface defects by the ambient exposure.

14 SOLAR ENERGY↗

Nanoscale Measurements of the Surface Photovoltage in Cu(In,Ga)Se2, Cu2ZnSn4, and Cu2ZnSnSe4 Thin Films: The Role of the Surface Electronics on the Efficiency of Solar Cells: Preprint

We report on recent advances in the development of nanoscale measurements of the surface photovoltage (SPV) based on scanning tunneling microscopy (STM) and its application to the kesterites Cu2ZnSnS4 (CZTS) and Cu2ZnSnSe4 (CZTSe). One critical aspect of the electronic structure of Cu(In,Ga)Se2 (CIGS) that has yet to be determined in their related kesterite compounds is the character of the surface electronics. In CIGS, spontaneous deviations in the stoichiometry of the surface cause a depletion (or even a type inversion) region that reinforces the CIGS homojunction. First-principle calculations predict that this inversion region will be more difficult to form in CZTS. In this contribution, the characteristics of the surface space charge region for both CIGS and CZTS(e) are investigated by STM. The implications of the results of these measurements on the future development of CZTS solar cells will be discussed.

14 SOLAR ENERGY↗

Kesterites and Chalcopyrites: A Comparison of Close Cousins; Preprint

Chalcopyrite solar cells based on CuInSe2 and associated alloys have demonstrated high efficiencies, with current annual shipments in the hundreds of megawatts (MW) range and increasing. Largely due to concern over possible indium (In) scarcity, a related set of materials, the kesterites, which comprise Cu2ZnSnS4 and associated alloys, has received increasing attention. Similarities anddifferences between kesterites and chalcopyrites are discussed as drawn from theory, depositions, and materials characterization. In particular, we discuss predictions from density functional theory, results from vacuum co-evaporation, and characterization via x-ray diffraction, scanning electron microscopy, electron beam-induced current, quantum efficiency, secondary ion mass spectroscopy, andluminescence.

14 SOLAR ENERGY↗

Photovoltaic manufacturing: Present status, future prospects, and research needs

In May 2010 the United States National Science Foundation sponsored a two-day workshop to review the state-of-the-art and research challenges in photovoltaic (PV) manufacturing. This article summarizes the major conclusions and outcomes from this workshop, which was focused on identifying the science that needs to be done to help accelerate PV manufacturing. A significant portion of the article focuses on assessing the current status of and future opportunities in the major PV manufacturing technologies. These are solar cells based on crystalline silicon (c-Si), thin films of cadmium telluride (CdTe), thin films of copper indium gallium diselenide, and thin films of hydrogenated amorphous and nanocrystalline silicon. Current trends indicate that the cost per watt of c-Si and CdTe solar cells are being reduced to levels beyond the constraints commonly associated with these technologies. With a focus on TW/yr production capacity, the issue of material availability is discussed along with the emerging technologies of dye-sensitized solar cells and organic photovoltaics that are potentially less constrained by elemental abundance. Lastly, recommendations are made for research investment, with an emphasis on those areas that are expected to have cross-cutting impact.

14 SOLAR ENERGY↗

Nanoscale Measurements of the Surface Photovoltage in Cu(In,Ga)Se2, Cu2ZnSnS4, and Cu2ZnSnSe4 Thin Films: The Role of the Surface Electronics on the Efficiency of Solar Cells

We report on recent advances in the development of nanoscale measurements of the surface photovoltage (SPV) based on scanning tunneling microscopy (STM) and its application to the kesterites Cu{sub 2}ZnSnS{sub 4} (CZTS) and Cu{sub 2}ZnSnSe{sub 4} (CZTSe). One critical aspect of the electronic structure of Cu(In, Ga)Se{sub 2} (CIGS) that has yet to be determined in their related kesterite compounds is the character of the surface electronics. In CIGS, spontaneous deviations in the stoichiometry of the surface cause a depletion (or even a type inversion) region that reinforces the CIGS homojunction. First-principle calculations predict that this inversion region will be more difficult to form in CZTS. In this contribution, the characteristics of the surface space charge region for both CIGS and CZTS(e) are investigated by STM. The implications of the results of these measurements on the future development of CZTS solar cells will be discussed.

14 SOLAR ENERGY↗