Search NASA⌕ Search

Engineering topics

Reynolds, John G.

Publications and source records attributed to Reynolds, John G..

At least 19 records

TATB thermal decomposition: Expanding the molecular profile with cryo-focused pyrolysis GC-MS

Understanding the molecular composition of high explosives during thermal decomposition is vital for predicting the sensitivity, safety, and performance of explosive materials. The thermal decomposition of 1,3,5-triamino-2,4,6-trinitrobenzene (TATB) has been linked to the formation of furazans through a series of dehydration reactions of the NO2 and NH2 groups on the phenyl ring, along with breakdown into small molecules (≤120 amu). Molecular identification of compounds formed in this transformation of the furazans to light gases has been lacking. To address this, we have applied a pseudo-confined sampling system in a cryo-focused pyrolysis gas chromatography-mass spectrometry (pyGC-MS) system to molecularly identify these intermediates. By design, sublimation of TATB, which has complicated MS analyses of thermal degradation, was significantly reduced and additional compounds were identified with potential structural information. In addition to the known furazan compounds, one of these compounds forms from the loss of oxygen from benzo-trifurazan (F3) and produces an open ring structure that may be the first step in the formation of lower molecular weight furazan breakdown products. The loss of a nitro group from benzo-monofurazan (F1) was also discovered and implicates the formation of oxidizing NO2 gas in the thermal decomposition mechanism. So these findings are vital for understanding the proper heat flow from energetic materials on a molecular level, necessary when measuring enthalpy and developing decomposition models based on kinetic parameters.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Analysis of degradation products in thermally treated TATB

Delineating the chemical composition of TATB (1,3,5-triamino-2,4,6-trinitrobenzene) residues produced from the exposure to abnormal thermal environments should lead to a better understanding of the decomposition paths. Identifying and quantifying each compound in thermally produced residues, monitors which compounds are degrading or forming along the decomposition route, as well as providing input for the kinetic models of those pathways. Here, in this paper, we report the methodology of isolating, identifying, and where possible, quantifying soluble compounds present in solid residues of thermally treated TATB (330 °C for tens of minutes). Samples were extracted with DMSO, separated using chromatography, and quantified using their absorption at 354 nm. Identification of unknown compounds was accomplished using high resolution mass spectrometry. TATB, F1 (diamino-dinitro-benzofurazan), HO-TATB (2,4,6-triamino-1-hydroxyl-3,5-dinitrobenzene), and T4A (1-chloro-3,5-dinitro-2,4,6-triaminobenzene) were trace compounds detected in the unreacted TATB. Ten more compounds that formed in the residues were structurally identified including F2 (amino-nitro-difurazan). Several more compounds were observed but not completely identified. We propose possible structures for the unknowns. Of the compounds formed, F1 was the most abundant compound reaching 4.5 % by weight of the degraded solid sample. Other degradation compounds were estimated to sum to trace levels, well below 1 %. Most compounds were new, having not been detected and identified in previous studies of production grade and thermally aged TATB. Many compounds only reached detectable concentrations after several min of thermal exposure.

36 MATERIALS SCIENCE↗

New thermal decomposition pathway for TATB

Abstract Understanding the thermal decomposition behavior of TATB (1,3,5-triamino-2,4,6-trinitrobenzene) is a major focus in energetic materials research because of safety issues. Previous research and modelling efforts have suggested benzo-monofurazan condensation producing H 2 O is the initiating decomposition step. However, early evolving CO 2 (m/z 44) along with H 2 O (m/z 18) evolution have been observed by mass spectrometric monitoring of head-space gases in both constant heating rate and isothermal decomposition studies. The source of the CO 2 has not been explained, until now. With the recent successful synthesis of 13 C 6 -TATB ( 13 C incorporated into the benzene ring), the same experiments have been used to show the source of the CO 2 is the early breakdown of the TATB ring, not adventitious C from impurities and/or adsorbed CO 2 . A shift in mass m/z 44 (CO 2 ) to m/z 45 is observed throughout the decomposition process indicating the isotopically labeled 13 C ring breakdown occurs at the onset of thermal decomposition along with furazan formation. Partially labeled (N 18 O 2 ) 3 -TATB confirms at least some of the oxygen comes from the nitro-groups. This finding has a significant bearing on decomposition computational models for prediction of energy release and deflagration to detonation transitions, with respect to conditions which currently do not recognize this oxidation step.

36 MATERIALS SCIENCE↗

Syntheses and characterization of isotopically labeled 1,3,5-triamino-2,4,6-trinitrobenzene (TATB)

Synthesis and characterization of chemical analogues of TATB, where specific atoms in the structure have been isotopically substituted, are reported. 15 N, 2 H, and 18 O have replaced the naturally occurring isotope distributions in the amino and/or the nitro attendant sites and 13 C has replaced the carbon in the ring structure. A modified wet-amination method was used to produce the analogues, and the isotopic replacements were performed by selective choice of labeled precursors. Four 15 N-labeled compounds (N replaced in the amino and nitro positions), two deuterium-labeled compounds (hydrogens replaced on the amino groups), and one 13 C-labeled compound (C in the ring substituted) were synthesized of high isotopic and chemical purity. One partially labeled 18 O-labeled compound (O in the nitro position) was a result of incomplete labeling due to exchange reactions during synthesis. The compounds were characterized by various spectroscopic methods – mass spectrometry (MS), solid-state nuclear magnetic resonance (SS-NMR), infrared (FTIR), powder x-ray diffraction (PXRD), and differential scanning calorimetry (DSC), depending upon the substitution. In conclusion, these compounds have been critical to the efforts in understanding the decomposition pathways of TATB when exposed to abnormal thermal environments.

36 MATERIALS SCIENCE↗

Towards a heat- and mass-balanced kinetic model of TATB decomposition

We report TATB (1,3,5-triamino-2,4,6-trinitrobenzene) was thermally degraded by two small-scale analytical methods – simultaneous differential scanning calorimetry and thermogravimetric analysis (SDT) and a hot-stage microscope with Fourier Transform Infrared (FTIR) analysis capabilities. SDT used ramped heating, isothermal soaking, and thermal pretreatment at various conditions. The heat flow and mass loss were monitored during various treatment conditions to derive chemical decomposition kinetics and Arrhenius parameters. FTIR experiments used isothermal heating, and changes were monitored spectroscopically. Solid samples generated at specific conditions were collected from both methods and were analyzed by DMSO extraction followed by chemical speciation by optical and mass spectrometric methods. Characterization provided the following reaction insights: TATB decreases in a sigmoidal pattern in isothermally heated samples. Other soluble products gradually increase in concentration and then abruptly decline in concentration during the second exotherm, such as diamino-dinitro-benzofurazan and amino-nitro-benzodifurazan. FTIR showed gradual changes in the amino and nitro functionality, shifting positions and decreasing intensity for the first 40 min. Then the solid gradually appeared more like an amorphous C with N incorporated, similar to previous studies on thermally degraded TATB-type materials. Extracted residues (DMSO-soluble components removed) examined by FTIR showed an abrupt change in chemical composition between 40- and 45-min isothermal treatment, indicating early forming solids are different than later forming residues. A reliable mass- and energy-balanced global reaction network must include at least two autocatalytic reactions, either in parallel or series, and at least one must have an explicit initiation reaction having a low activation energy.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Comparative analysis of sublimation and thermal decomposition of TATB

This experimental study investigated the effects of confinement, starting mass, and heating rate on TATB thermal decomposition and sublimation using a combined Thermo-Gravimetric Analyzer and Differential Scanning Calorimetry (TGA/DSC) instrument. The confinement of volatile products was varied using different pinhole sizes with TGA/DSC pans. The measurements showed the open pan experiments without lids/pinholes resulted in complete sublimation of TATB between 320 °C and 360 °C. The heat of sublimation was determined to be 176 kJ/mol (42 kcal /mol), consistent with literature data obtained from other experimental techniques. The use of pinholes suppressed the sublimation of TATB such that the decrease in pinhole size resulted in 1) an increase in the enthalpy of reaction and an increase in the amount of carbonaceous material remaining at the end of decomposition, and 2) convergence of the two peak temperatures corresponding to maximum heat flow and maximum weight loss. Also, a transition from a two-exotherm thermal decomposition behavior towards a single-exotherm occurred as the pinhole size was decreased for a given starting mass or as the starting mass was increased for a given pinhole size. These results indicate the kinetics of TATB sublimation, TATB thermal decomposition, and gas diffusion out of a TGA/DSC pan can all compete and result in significantly different enthalpies, amounts of remaining materials, and peak temperatures depending on the pinhole size and starting mass used in the measurements. Furthermore, the results also indicate precise control of process variables (pinhole size, starting mass, and heating rate) in TGA/DSC measurements is required for thermal safety assessment of explosives.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Trace Compound Analysis in TATB by Liquid Chromatography coupled with Spectroscopic and Spectrometric Detection

Accurate quantitation of 1,3,5-triamino-2,4,6-trinitrobenzene (TATB) is important because of its strategic use as an energetic material. A purity determination is also needed for the proper assessment of performance. A fast and sensitive method has been developed to measure the purity of TATB in polymer-bonded materials. The target material is extracted with DMSO, and the extract is separated on a reversed-phase chromatography column. The column effluent is monitored by diode array detection (DAD) at 354 nm. The characteristic UV-Vis response and retention time identify the individual components when compared to pure compound standards. The chemical structures of compounds with no pure standards available have been determined by high-resolution mass spectrometry (MS) and MS/MS. The major component, TATB, along with 1-chloro-3,5-dinitro-2,4,6-triaminobenzene (T4A) and mono-benzofuroxan (FX1) were quantitated directly from pure compound standards. Several trace concentration components, mono-benzofurazan (F1), 1-bromo-3,5-dinitro-2,4,6-triaminobenzene (Br-T4A), 2,4,6-triamino-1-nitroso-3,5-dinitrobenzene (MN-TATB), 2,4,6-triamino-1-hydroxyl-3,5-dinitrobenzene (HO-TATB), and 2,4,6-triamino-1-nitrile-3,5-dinitrobenzene (Nitrile-TATB) were also detected and structures verified via MS/MS. Approximate concentrations were determined using calibrations from standards of similar structures. Additional trace components were also detected by MS. Contained herein are the results of analyses of TATB-based materials characterized for polymer-bonded formulations compared to different preparations of TATB. The accuracy, details, and process of developing this method are reported here.

36 MATERIALS SCIENCE↗

Enhanced colorimetric apparatus and method for explosives detection using ionic liquids

An inspection tester for testing a surface for suspected explosive substances includes a body unit, a breakable ampoule carried by the body unit, and an ionic explosive detecting reagent in the breakable ampoule wherein the body unit and the breakable ampoule are positioned to deliver the ionic explosive detecting reagent to the surface for testing the surface for the suspected explosive substances. The ionic explosive detecting reagent is a salt in a liquid state.

Reynolds, John G.↗

Experimental Investigation of the Thermal Decomposition Pathways and Kinetics of TATB by Isotopic Substitution

Real-time measurements of the product gases arising from the thermal decomposition of triamino-trinitro benzene (TATB), its deuterated analogue, and plastically bonded TATB (LX-17) are presented in this study. Gas-phase decomposition products are identified by IR absorption spectroscopy. The frequency shifts in rovibrational spectra due to isotopic substitution and the change in rate of formation of decomposition products due to the kinetic-isotope-effect (KIE) help elucidate the decomposition pathways. The formation of H 2 O precedes other molecules (e.g., HCN, HNCO) during decomposition. After the concentrations of HCN and HNCO molecules reach a peak, their amounts gradually decrease. The concentrations of the other decomposition products (e.g., NH 3 and CO 2 ) rapidly rise after an induction period, which is attributed to the presence of autocatalytic reactions. The trends of chemical evolution are similar for all the samples, but their kinetic behaviors are different. This indicates the rates of consistent pathways are changed during thermal decomposition. Additionally, the kinetics of deuterated TATB decomposition is slower than that of unsubstituted TATB due to the KIE (kH/kD~1.41). The rate of LX-17 decomposition is slightly lower than unsubstituted TATB (k TATB /k LX-17 ~1.15). The KIE is more pronounced during the early stage of decomposition, which is attributed to the first steps of TATB decomposition involving water formation (i.e., H vs D transfer). The KIE slows down the formation of all gases, including those lacking hydrogen (e.g., CO 2 ). These results suggest the TATB thermal decomposition mechanism might involve a series of pathways rather than a set of independent and parallel reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

LX-17 Thermal Decomposition-Characterization of Solid Residues from Cook-Off in a Small-Scale Vessel Under Confinement

Concerns surround whether insensitive (or any) energetic materials are more dangerous to handle when exposed to abnormal thermal environments. This study characterizes the residual material remaining after LX-17 (92.5 % 1,3,5-triamino 2,4,6-trinitro benzene (TATB) and 7.5 % Kel-F) is exposed to various thermal environments in a sealed small-scale vessel cook-off test reactor (heated at 0.1 to 100 °C/min until the reactor opened at 3000 psi (20.7 MPa)). Previous work has shown no additional sensitivity of these residues as evaluated by small-scale safety analysis, but characterization on the molecular scale indicates the TATB is transformed to more reactive compounds as well as the residue could be precursors to toxic gases. The solids and chars were characterized by various analytical methods. Heat-flow measurements indicated exothermic release is due to a mixture of residual TATB and related decomposition products (which may be more energetic). The N/C and O/N ratios indicated a material much more degraded than TATB. Primarily, the solids were a network of amorphous C inter-dispersed with N and O. Types of bonding include C–C, C–N, N–H, N–C, N=C, N≡C, C–O=, and –OH. Solvent extracts of the solids showed TATB decomposition intermediates benzo-furazans and benzo-furoxans, substituted TATB (mono-nitroso, hydroxyl, and chlorinated) along with several unidentified smaller molecules. These results indicate thermal treatment produces an amorphous carbon residue with heteroatoms incorporated through differing functionality, varying depending upon the thermal severity of exposure. These structures also could further decompose producing toxic light gases (such as cyanide).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Systems and methods for generation of hydrogen peroxide vapor

A method according one embodiment includes at least one of bubbling dried air through a hydrogen peroxide solution in a container for producing a first hydrogen peroxide vapor, and passing dried air from the moisture trap into a headspace above the hydrogen peroxide solution in a container for producing a second hydrogen peroxide vapor. Additional systems and methods are also presented.

Love, Adam H.↗

Reduction of Nitrogen Oxide Emission for Lean Burn Engine Technology Final Report CRADA No. TC-315-92C

This report is a written version of the technical review presentation which was to be given to the Lean NOx Catalyst CRADA Project Progress Discussions and Planning Meeting, on October 8,1996. The goal objective of this project is to develop aerogel catalysts for catalytic converter systems capable of meeting new and future Clean Air Act requirements.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

K-9 training aids made using additive manufacturing

Additive Manufacturing (AM) is used to make aids that target the training of K-9s to detect explosives. The process uses mixtures of explosives and matrices commonly used in AM. The explosives are formulated into a mixture with the matrix and printed using AM techniques and equipment. The explosive concentrations are kept less than 10% by wt. of the mixture to conform to requirements of shipping and handling.

42 ENGINEERING↗

Explosives mimic for testing, training, and monitoring

Additive Manufacturing (AM) is used to make mimics for explosives. The process uses mixtures of explosives and matrices commonly used in AM. The explosives are formulated into a mixture with the matrix and printed using AM techniques and equipment. The explosive concentrations are kept less than 10% by wt. of the mixture to conform to requirements of shipping and handling.

36 MATERIALS SCIENCE↗

Effect of Sandpaper and Grain Size on Non‐Shock Initiated Reactions in HMX

Abstract Three grades of HMX samples, coarse (A), coarse with a small amount of fines (B), and ultra‐fine (F), were tested for impact sensitivity by ERL drop hammer. The Type 12A test used sandpapers of three different compositions, 120‐, 180‐grit Si/C and 180‐grit garnet. Reaction was accounted for by operator observation and microphone. The results showed different sensitivity for each of the HMX types. The F‐HMX was the smallest in average particle size and was the least sensitive to impact. The A‐HMX was the next most stable and the B‐HMX was the most sensitive to impact. The spent samples from the drop hammer testing of B‐HMX and F‐HMX were further evaluated with optical imaging. Conditions were selected that were near the DH 50 values of the specific HMX. Previous literature has cited localized hot spot formation to be the probable cause of non‐shock initiated reactions leading to impact sensitivity. This study yielded a plethora of samples exhibiting hot spots for HMX materials, both without and with proximity to grit particles. Hot spots in the proximity of grit particles gave the most dramatic hot spots, but both types of hot spots were exhibited in samples considered reacted and non‐reacted. The F‐HMX, even though the most stable to impact sensitivity, exhibited the most and best resolved hot spots of all the samples and conditions. Foreign objects were also observed in some of the samples. Previous work has shown metal particles coming from wear of the anvils used in the drop hammer experiment can also form hot spots. However, none of the samples here with metal particles exhibited, in proximity, hot spot formation.

Reynolds, John G.↗