Riccardo, V. | Search NASA

DOE OSTI2020

Reduction of asymmetric wall force in JET and ITER disruptions including runaway electrons

It was shown that asymmetric vertical displacement event (AVDE) disruptions in JET and ITER do not produce a large asymmetric force on conducting structures surrounding the plasma, provided that the current quench (CQ) time is less than the resistive wall penetration time. This is verified with JET data. In ITER the CQ is expected to be comparable to the resistive wall penetration time, which gives a small wall force. It is shown that runaway electrons (REs) in JET do not produce a large wall force, and this is verified with JET data. This occurs if the RE current is about half of the initial plasma current. In ITER, the RE current might be comparable to the initial current, and REs might lengthen the CQ time sufficiently to produce a large wall force.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2019

The ITPA disruption database

A multi-device database of disruption characteristics has been developed under the auspices of the International Tokamak Physics Activity magneto-hydrodynamics topical group. The purpose of this ITPA disruption database (IDDB) is to find the commonalities between the disruption and disruption mitigation characteristics in a wide variety of tokamaks in order to elucidate the physics underlying tokamak disruptions and to extrapolate toward much larger devices, such as ITER and future burning plasma devices. In contrast to previous smaller disruption data collation efforts, the IDDB aims to provide significant context for each shot provided, allowing exploration of a wide array of relationships between pre-disruption and disruption parameters. The IDDB presently includes contributions from nine tokamaks, including both conventional aspect ratio and spherical tokamaks. An initial parametric analysis of the available data is presented. This analysis includes current quench rates, halo current fraction and peaking, and the effectiveness of massive impurity injection. The IDDB is publicly available, with instruction for access provided herein.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2018

An improved model for the accurate calculation of parallel heat fluxes at the JET bulk tungsten outer divertor

Parallel heat flux calculations at the JET divertor have been based on the assumption that all incoming heat is due to the projection of the heat flux parallel to the magnetic line, q ∥ , plus a constant background. This simplification led to inconsistencies during the analysis of a series of dedicated tungsten melting experiments performed in 2013, for which infrared (IR) thermography surface measurements could not be recreated through simulations unless the parallel heat flux was reduced by 80% for L-mode and 60% for H-mode. We give an explanation for these differences using a new IR inverse analysis code, a set of geometrical corrections, and most importantly an additional term for the divertor heat flux accounting for non-parallel effects such as cross-field transport, recycled neutrals or charge exchange. This component has been evaluated comparing four different geometries with impinging angles varying from 2 to 90°. Its magnitude corresponds to 1.2%–1.9% of q ∥ , but because it is not affected by the magnetic projection, it accounts for up to 20%–30% of the tile surface heat flux. The geometrical corrections imply a further reduction of 24% of the measured heat flux. In addition, the application of the new inverse code increases the accuracy of the tile heat flux calculation, eliminating any previous discrepancy. The parallel heat flux computed with this new model is actually much lower than previously deduced by inverse analysis of IR temperatures—40% for L-mode and 50% for H-mode—while being independent of the geometry on which it is measured. This main result confirms the validity of the optical projection as long as a non-constant and non-parallel component is considered. For a given total heating power, the model predicts over 10% reduction of the maximum tile surface heat flux compared to strict optical modelling, as well as a 30% reduced sensitivity to manufacturing and assembling tolerances. Furthermore these conclusions, along with the improvement in the predictability of the divertor thermal behaviour, are critical for JET future DT operations, and are also directly applicable to the design of the ITER divertor monoblocks.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗