Search NASA⌕ Search

Engineering topics

Richards, P. L.

Publications and source records attributed to Richards, P. L..

At least 19 records

Focal Plane Arrays of Voltage-Biased Superconducting Bolometers

The 200-micrometer to 3-mm wavelength range has great astronomical and cosmological significance. Science goals include characterization of the cosmic microwave background, measurement of the Sunyaev-Zel'dovich effect in galaxy clusters, and observations of forming galaxies. Cryogenic bolometers are the most sensitive broadband detectors in this frequency range. Because single bolometer pixels are reaching the photon noise limit for many observations, the development of large arrays will be critical for future science progress. Voltage-biased superconducting bolometers (VSBs) have several advantages compared to other cryogenic bolometers. Their strong negative electrothermal feedback enhances their linearity, speed, and stability. The large noise margin of the SQUID readout enables multiplexed readout schemes, which are necessary for developing large arrays. In this paper, we discuss the development of a large absorber-coupled array, a frequency-domain SQUID readout multiplexer, and an antenna-coupled VSB design.

Myers, Michael J.↗

New technologies for the detection of millimeter and submillimeter waves

Voltage-biased superconducting bolometers have many operational advantages over conventional bolometer technology including sensitivity, linearity, speed, and immunity from environmental disturbance. A review is given of the Berkeley program for developing this new technology. Developments include fully lithographed individual bolometers in the spiderweb configuration, arrays of 1024 close-packed absorber-coupled bolometers, antenna-coupled bolometers, and a frequency-domain SQUID (superconducting quantum interference device) readout multiplexer.

Richards, P. L.↗

Measurements of the millimeter-wave spectrum of interstellar dust emission

We report measurements of the differential brightness of interstellar dust emission near the Galactic plane and at high Galactic latitudes. The data were obtained as part of a program to measure anisotropy in the cosmic microwave background (CMB). The measurements were made with a 0.5 deg beam size and a 1.3 deg sinusoidal chop, in broad bands (Delta nu/nu approximately 0.3) centered near frequencies of 6, 9, and 12 cm(exp -1). A measurement made toward the Galactic plane, at longitude 1 = 23.7 deg, is compared with the contrast observed in the 100 micrometers IRAS data. Assuming the dust emission has a brightness I(sub nu) proportional to nu(sup n)B(sub nu)(T(sub d)), where B(sub nu) is the Planck function, a best fit yields n = 1.6 +/- 0.4, T(sub d) = 24 +/- 5 K. In a region near the star mu Pegasi (mu PEG l = 91 deg, b = -31 deg), the comparison of our data with the 100 micrometers IRAS data yields n = 1.4 +/- 0.4, and T(sub d) = 18 +/- 3 K. In a second region near the star gamma Ursa Minoris (GUM l = 108 deg, b = 41 deg), an upper limit is placed on contrast in dust emission. This upper limit is consistent with spectrum measured at mu PEG and the IRAS 100 micrometer emission contrast at GUM, which is approximately 8 times lower than mu PEG.

Fischer, M. L.↗

A rocket-borne observation of the far-infrared sky at high Galactic latitude

We have measured the surface brightness of the far-infrared sky at lambda = 134, 154, and 186 micrometers at high Galactic latitude using a liquid-He-cooled, rocket-borne telescope. The telescope scanned over a 5 deg x 20 deg region which includes infrared cirrus, high-latitude molecular clouds, the starburst galaxy M82, and the H I Hole in Ursa Major, a region with uniquely low H I column density. The measured brightness at 134, 154, and 186 micrometers is well correlated with the 100 micrometers brightness measured by IRAS and, in regions excluding molecular clouds, with H I column density. The spectrum of the component correlated with H I is well fitted by a gray-body spectrum with a temperature of 16.4 (+2.3/-1.8) K, assuming an emissivity proportional to lambda(exp -2). Assuming a constant far-infrared dust emissivity per hydrogen nucleus, the ratio of the H2 column density to the velocity-integrated CO intensity in the high-latitude molecular cloud is NH2/W(sub co) = (1.6 +/- 0.3) x 10(exp 20)/sq cm/(K km/s). The residual brightness after subtracting the emission correlated with H I column density is lambda I(sub lambda)(154 micrometers) = (1.4 +/- 0.6) x 10(exp -12) W/sq cm/sr, yielding an upper limit to the far-infrared extragalactic background radiation of lambda I(sub lambda)(154 micrometers) is less than 2.6 x 10(exp -12) W/sq cm/sr.

Kawada, M.↗

A degree scale anisotropy measurement of the cosmic microwave background near the star Gamma Ursae Minoris

Results from a search for anisotropy in the cosmic microwave background (CMB) are presented from the third flight of the Millimeter-wave Anisotropy experiment. The CMB observation occurred over 1.37 hours and covered a 6.24 sq deg area of the sky where very little foreground emission is expected. Significant correlated structure is observed at 6 and 9/cm. At 12/cm we place an upper limit on the structure. The relative amplitudes at 6, 9, and 12/cm are consistent with a CMB spectrum. The spectrum of the structure is inconsistent with thermal emission from known forms of interstellar dust. Synchrotron and free-free emission would both require unusually flat spectral indices at cm wavelengths in order to account for the amplitude of the observed structure. Although known systematic errors are not expected to contribute significantly to any of the three optical channels, excess sidelobe contamination cannot be definitively ruled out. If all the structure is attributed to CMB anisotropy, a value of the weighted rms of the 6 and 9/cm channels of Delta T/T(CMB) = 4.7 +/- 0.8 x 10 exp -5 (+/- 1 sigma) was measured. If the CMB anisotropy is assumed to have a Gaussian autocorrelation function with a coherence angle of 25 arcmin, then the most probable value is Delta T/T(CMB) = 4.2 +1.7 or -1.1 x 10 exp -5, where the +/- refers to the 95 percent confidence limits.

Gundersen, J. O.↗

Observation of forbidden C II 158 micron emission from the diffuse interstellar medium at high Galactic latitude

We report the first detection of forbidden C II 158 micron line emission from the diffuse interstellar medium at high Galactic latitude. We have measured the integrated line intensity in a 36 arcmin field of view along a triangular scan path in a 5 x 20 deg region in Ursa Major using a rocket-borne, liquid-helium-cooled spectrophotometer. The scan included high-latitude infrared cirrus, molecular clouds, a bright external galaxy, M82, and the H I Hole, which is a region of uniquely low neutral hydrogen column density. Emission from forbidden C II is observed in all regions, and, in the absence of appreciable CO emission, it is well correlated with neutral hydrogen column density. We observe a forbidden C II gas cooling rate which varies from (1.18 +/- 0.4 to 3.25 +/- 0.8) x 10 exp -26 ergs/s/H atom. Regions with CO emission have enhanced forbidden C II line emission over that expected from the correlation with neutral hydrogen column density. We measure a line-to-continuum ratio which varies from 0.002 to 0.008 in comparison with the all-sky average of 0.0082 reported by FIRAS, which is heavily weighted toward the Galactic plane.

Bock, J. J.↗

A two-stage magnetic refrigerator for astronomical applications with reservoir temperatures above 4 K

We propose a novel adiabatic demagnetization refrigerator (ADR) to produce temperatures as low as 100 mK starting from a high temperature reservoir between 4 and 8 K. The high temperature reservoir for the ADR can be provided by a mechanical cooler or an unpumped liquid helium bath. This refrigerator can be used to cool bolometric infrared detectors for low background astronomy from mountain tops, balloons or satellites as well as to cool cryogenic x-ray detectors. The two-stage ADR consists of a single magnet with a paramagnetic chromic-cesium-alum (CCA) salt pill to produce the low temperature and paramagnetic gadolinium-gallium-garnet (GGG) as the first stage to intercept heat from the high temperature reservoir. Thermal contact between the paramagnets and the reservoir during magnetization is made with a mechanical heat switch. The ADR is suspended with Kevlar chords under tension for high mechanical stiffness and low parasitic heat leak. In a single cycle, the ADR maintains a temperature of 100 mK for 10 to 100 hours. This time depends strongly on the magnetic field and reservoir temperature but not on the volume of the paramagnetic material as long as the heat leak is dominated by the suspension.

Hagmann, C.↗

A broadband THz receiver for low background space applications

We have developed a sensitive bolometric receiver for low background space applications. In a 10 percent bandwidth at 1 THz, this receiver is approximately 100 times more sensitive than a quantum limited heterodyne receiver with a 1 GHz IF bandwidth. This receiver is designed to be used for the long wavelength band (200-700 microns) in the MIPS instrument on NASA's SIRTF satellite. The bolometers are cooled to 100 mK by an adiabatic demagnetization refrigerator. Roughly 60 g of cesium chrome alum salt is partially demagnetized to 100 mK, followed by a slow regulated downramp to compensate for the heat leak. The hold time of the ADR system is about 18 hours with a temperature stability of delta T(sub rms) approx. equals 10 micro-K. The composite bolometers have electrical responsivities of 10(exp 9)V/W and electrical NEP's of about 3x10(exp -17) W/square root of Hz. The bolometer signals are read out by JFET preamplifiers located on the helium plate and operated at 120 K. We have addressed a number of space qualification issues, such as the development of an analog magnet controller, construction of a cryogenic shake-table for bolometers and selection of the paramagnetic salt CCA which can survive a bakeout at 50 C. The receiver is scheduled to be flown in the spring of 1992 on a balloon telescope. This flight has a dual purpose. One is to provide realistic test of the capabilities of the new receiver. The other is to search for anisotropies in the cosmic microwave background on scales of a few degrees.

Hagmann, C.↗

A millimeter-wave anisotropy experiment (MAX) to search for anisotropy in the cosmic background radiation on medium angular scales

We report preliminary results from two balloon flights of a millimeter-wave telescope designed to measure anisotropy in the cosmic microwave background (CMB) on angular scales from 0.3 to 3 degrees. The receiver used in the first flight, in November 1989, was a dichroic, He-3-cooled bolometric photometer with passbands centered at 3, 6, 9, and 12/cm. The second flight, in July 1990, employed improved bolometric detectors. The 3/cm band was removed in order to increase the efficiency of the remaining bands. Preliminary analysis of the data gives a factor of 3 improvement in sensitivity over the first flight in the 6/cm band. Future plans include a new receiver to provide an additional factor of 5 improvement in sensitivity and a new balloon-borne telescope which is optimized for low-background bolometric detectors at millimeter wavelengths.

Fischer, M. L.↗

A measurement of the spectrum of the cosmic background radiation from 1 to 3 millimeter wavelength

The brightness temperature of the sky is measured in five bands from 1 to 3 mm using apparatus related to that of Woody and Richards (1981) and Peterson et al. (1985). Examination of the data reveals the presence of two previously unknown systematic effects which limit the accuracy of the measurements. Similar systematic effects are most likely present in the data obtained previously with this apparatus. Upper limits to the temperature of the cosmic background radiation are set in four bands; the most stringent is T(CBR) less than 2.88 K at 1.1 mm (95 percent CL).

Bernstein, G. M.↗

Stressed Ge:Ga photoconductors for space-based astronomy. (Is there life beyond 120 micron)

Information is given in viewgraph form. Information is given on the characteristics of stressed Ge:Ga, a spring type stress cavity, mounting hardware, materials parameters affecting dark current, and the behavior of low dark current stressed Ge:Ga. It is concluded that detectors exist today for background-limited detection at 200 microns, that researchers are narrowing in on the significant parameters that effect dark current in stressed photoconductors, that these findings may be applied to other photoconductor materials, and that some creative problem solving for an ionizing effect reset mechanism is needed.

Beeman, J. W.↗

A 100 micro Kelvin bolometer system for SIRTF

Progress toward a prototype of 100 mK bolometric detection system for the Space Infrared Telescope Facility (SIRTF) is described. Two adiabatic demagnetization refrigerators (ADR's) were constructed and used to investigate the capabilities necessary for orbital operation. The first, a laboratory ADR, demonstrated a hold time at 0.1 K of over 12 hours, with temperature stability approx. 3 micro-K RMS achieved by controlling the magnetic field. A durable salt pill and an efficient support system have been demonstrated. A second ADR, the SIRTF flight prototype, has been built and will be flown on a balloon. Techniques for magnetic shielding, low heat leak current leads, and a mechanical heat switch are being developed in this ADR. Plans for construction of 100 mK bolometers are discussed. Three important cosmological investigations which will be carried out by these longest wavelength SIRTF detectors are described.

Bernstein, G. M.↗

Anisotropy of the diffuse background at millimeter wavelengths

The anisotropy of the diffuse background radiation has been measured with a 10-deg FWHM beam in a broad spectral band from 0.6 to 4.0 mm. A dipole anisotropy is detected with magnitude consistent with previous measurements; the present data may, however, be contaminated by atmospheric emission. Upper limits are set to fluctuations at higher-order multipoles. The most stringent limit is at l = 4, where a 95-percent confidence-level limit of less than 0.00025 is set. The observed level of isotropy sharply constrains the possibility of local astronomical origin for the submillimeter excess.

Bernstein, G. M.↗

An adiabatic demagnetization refrigerator for SIRTF

An adiabatic demagnetization refrigerator (ADR) has been proposed to cool bolometric infrared detectors on the multiband imaging photometer of the Space Infrared Telescope Facility (SIRTF). One such refrigerator has been built which uses a ferric ammonium alum salt pill suspended by nylon threads in a 3-T solenoid. The resonant modes of this suspension are above 100 Hz. The heat leak to the salt pill is less than 0.5 microW. The system has a hold time at 0.1K of more than 12 h. The cold stage temperature is regulated with a feedback loop that controls the magnetic field. A second, similar refrigerator is being built at a SIRTF prototype to fly on a ballon-borne telescope. It will use a ferromagnetic shield. The possibility of using a high-Tc solenoid-actuated heat switch is also discussed.

Timbie, P. T.↗

Accurate experimental and theoretical comparisons between superconductor-insulator-superconductor mixers showing weak and strong quantum effects

A systematic study of the gain and noise in superconductor-insulator-superconductor mixers employing Ta based, Nb based, and Pb-alloy based tunnel junctions was made. These junctions displayed both weak and strong quantum effects at a signal frequency of 33 GHz. The effects of energy gap sharpness and subgap current were investigated and are quantitatively related to mixer performance. Detailed comparisons are made of the mixing results with the predictions of a three-port model approximation to the Tucker theory. Mixer performance was measured with a novel test apparatus which is accurate enough to allow for the first quantitative tests of theoretical noise predictions. It is found that the three-port model of the Tucker theory underestimates the mixer noise temperature by a factor of about 2 for all of the mixers. In addition, predicted values of available mixer gain are in reasonable agreement with experiment when quantum effects are weak. However, as quantum effects become strong, the predicted available gain diverges to infinity, which is in sharp contrast to the experimental results. Predictions of coupled gain do not always show such divergences.

Mcgrath, W. R.↗

Stressed photoconductive detector for far-infrared space applications

An optimized leaf-spring apparatus for applying uniaxial stress to a Ge:Ga far-IR photoconductor has been designed and tested. This design has significant advantages for space applications which require high quantum efficiency and stable operation over long periods of time. The important features include adequate spring deflection with relatively small overall size, torque-free stress, easy measurement of applied stress, and a detector configuration with high responsivity. One-dimensional arrays of stressed photoconductors can be constructed using this design. A peak responsivity of 38 A/W is achieved in a detector with a cutoff wavelength of 200 microns, which was operated at a temperature of 2.0 K and a bias voltage equal to one-half of the breakdown voltage.

Wang, J.-Q.↗

Optical efficiency of far-infrared photoconductors

The present optimization of the geometry of far-IR photoconductive detectors with diffraction-limited throughput, on the basis of experimental and theoretical results, gives attention to the internal optical path relative to measured absorption length, photoconductive gain, uniformity of illumination, cosmic ray cross section, and design compatibility with the requirements of one- and two-dimensional arrays. It is demonstrated that a rod-shaped, square cross section detector geometry, having lateral face electrodes and a beveled backface with which to trap the radiation by total internal reflection, exhibits responsivity commensurate with that of the best available detectors in integrating cavities.

Wang, J.-Q.↗

Spectrum of the cosmic background radiation at millimeter wavelengths

The spectrum of the cosmic background radiation in five frequency bands extending from 2.3 to 11.0 cm with a balloon-borne liquid-helium-cooled photometer. The photometer compares the flux from the sky to the flux from an internal blackbody at 3.2 K. All five measurements are consistent with temperatures in the range 2.78 + or = 0.11 K, which is in good agreement with tempratures measured at lower frequencies. No significant deviation from a thermal spectrum was found.

Peterson, J. B.↗