Search NASA⌕ Search

Engineering topics

Richardson, E. H.

Publications and source records attributed to Richardson, E. H..

9 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2014

Solid Rocket Launch Vehicle Explosion Environments

Empirical explosion data from full scale solid rocket launch vehicle accidents and tests were collected from all available literature from the 1950s to the present. In general data included peak blast overpressure, blast impulse, fragment size, fragment speed, and fragment dispersion. Most propellants were 1.1 explosives but a few were 1.3. Oftentimes the data from a single accident was disjointed and/or missing key aspects. Despite this fact, once the data as a whole was digitized, categorized, and plotted clear trends appeared. Particular emphasis was placed on tests or accidents that would be applicable to scenarios from which a crew might need to escape. Therefore, such tests where a large quantity of high explosive was used to initiate the solid rocket explosion were differentiated. Also, high speed ground impacts or tests used to simulate such were also culled. It was found that the explosions from all accidents and applicable tests could be described using only the pressurized gas energy stored in the chamber at the time of failure. Additionally, fragmentation trends were produced. Only one accident mentioned the elusive "small" propellant fragments, but upon further analysis it was found that these were most likely produced as secondary fragments when larger primary fragments impacted the ground. Finally, a brief discussion of how this data is used in a new launch vehicle explosion model for improving crew/payload survival is presented.

Richardson, E. H.↗
NASA NTRS2005

Review of NASA In-Space Propulsion Technology Program Inflatable Decelerator Investments

The NASA In-Space Propulsion Technology (ISPT) Program is managed by the NASA Headquarters Science Mission Directorate and is implemented by the Marshall Space Flight Center in Huntsville, Alabama. The ISPT objective is to fund development of promising in-space propulsion technologies that can decrease flight times, decrease cost, or increase delivered payload mass for future science missions. Before ISPT will invest in a technology, the Technology Readiness Level (TRL) of the concept must be estimated to be at TRL 3. A TRL 3 signifies that the technical community agrees that the feasibility of the concept has been proven through experiment or analysis. One of the highest priority technology investments for ISPT is Aerocapture. The aerocapture maneuver uses a planetary atmosphere to reduce or alter the speed of a vehicle allowing for quick, propellantless (or using very little propellant) orbit capture. The atmosphere is used as a brake, transferring the energy associated with the vehicle's high speed into thermal energy. The ISPT Aerocapture Technology Area (ATA) is currently investing in the development of advanced lightweight ablative thermal protection systems, high temperature composite structures, and heat-flux sensors for rigid aeroshells. The heritage of rigid aeroshells extends back to the Apollo era and this technology will most likely be used by the first generation aerocapture vehicle. As a second generation aerocapture technology, ISPT is investing in three inflatable aerodynamic decelerator concepts for planetary aerocapture. They are: trailing ballute (balloon-parachute), attached afterbody ballute, and an inflatable aeroshell. ISPT also leverages the NASA Small Business Innovative Research Program for additional inflatable decelerator technology development. In mid-2004 ISPT requested an independent review of the three inflatable decelerator technologies funded directly by ISPT to validate the TRL and to identify technology maturation concerns. An independent panel with expertise in advanced thin film materials, aerothermodynamics, trajectory design, and inflatable structures was convened to assess the ISPT investments. The panel considered all major technical subsystems including materials, aerothermodynamics, structural dynamics, packaging, and inflation systems. The panel assessed the overall technology readiness of inflatable decelerators to be a 3 and identified fluid- structure interaction, aeroheating, and structural adhesives to be of highest technical concern.

Richardson, E. H.↗
NASA NTRS1990

Design of a shuttle-based space debris telescope

A 1.6-meter diameter f/0.95 all-reflecting telescope was designed to observe orbital debris particles as small as 1 mm from the shuttle payload bay. The telescope was specified to have a flat focal surface without the imposition of refractive elements. Two design configurations involving three mirrors were evaluated - a reflective Schmidt-Cassegrain and a modified Paul corrector. The Paul system was found to be more compact and appropriate for this application.

Richardson, E. H.↗
NASA NTRS1984

Optical matching for fiber optic spectroscopy

Single silica fibers of the type developed for communications are useful in the design of astronomical spectrographs. They can be used to couple light from many objects over a wide field to a single spectrograph, or to eliminate wavelength errors from image motion and gravitational flexure. For many applications it will be advantageous to use small lenses to make the most efficient coupling into and out of a fiber. If the telescope pupil is imaged on the fiber core, an efficient coupling can be made that preserves image size over a certain range. This method is demonstrated by a laboratory test using sapphire spheres as coupling lenses.

Hill, J. M.↗
NASA NTRS1973

Solar Electric Propulsion Stage design

This paper summarizes the analyses and design studies performed for the Solar Electric Propulsion Stage (SEPS). Mission analysis results were used to establish general design requirements. A performance sensitivity analysis was then used to define an operational power level of 21 kW for accomplishing a broad range of interplanetary and earth-orbital missions. With this base, propulsion system and stage subsystem design analyses were performed to support concept and configuration studies. Design study areas include solar array, thrust subsystem, thermal control, structures, and astrionics. Results are presented primarily for areas not covered by more specific technical papers (i.e., thrust subsystem, solar array, design requirements and configuration studies).

Masek, T. D.↗
NASA NTRS1972

The solar electric propulsion stage concept for high energy missions.

Definition of multimission and engine performance requirements for candidate solar electric propulsion stage configurations, considering launch vehicle compatibility, electric propulsion integration, payload requirements, and the effects of environmental extremes. Electric propulsion power options include two solar array power levels (15/22 kW), up to twelve electric thrustors of 30 cm diameter and 2.7 kW each, five to eight power conditioning units, and a maximum mercury propellant capacity of 1530 kg. In performance, the stage with a dry weight of 700 to 900 kg can deliver a net mass of 756 kg into Saturn orbit, 329 kg into a tight Mercury orbit, and 334 kg within 0.1 AU of the sun. The stage can also deliver a round trip payload of 3350 kg to geosynchronous orbit and return from an intermediate elliptical orbit using the Shuttle/Tug. Thus, a versatile stage is developed which competes effectively in performance with existing integrated spacecraft and promises considerable savings in total program costs.

Guttman, C. H.↗