Search NASA⌕ Search

Engineering topics

Richmond, David J.

Publications and source records attributed to Richmond, David J..

Assessment of Technical Information Needs and Considerations for Front-End Activities for Molten Salt Fuel Types

This report details an assessment of the hazards and safety impacts related to front-end operations of molten salt reactors (MSR) as well as an assessment of existing safety guidance. Publicly available information was evaluated to make recommendations to the U.S. Nuclear Regulatory Commission (NRC) for guidance development and information gathering needs. Five different MSR technologies were evaluated along with information from 1960’s about the Atomic Energy Commission programs for the Aircraft Reactor Experiment and Molten Salt Reactor Experiment. Primary areas of evaluation include fuel cycle facilities, transportation and at reactor fuel mixing operations up to reactor startup. In general, there was difficulty synthesizing publicly available information due to the early stage of the MSR development and proprietary information associated with the reactor technology companies analyzed. There are a few specific recommendations from this report. One overarching paradigm shift that the NRC needs to evaluate is the possibility of collocating fuel cycle facilities with operating MSRs. Although there is no specific prohibition to this in the NRC regulations, the collocation of the fuel cycle facilities with the operating MSR presents a novel approach compared to the light water reactor baseline. More guidance and research into thorium operations and regulation is needed. The hazards associated with the stability of stored fuel constituents need to be evaluated. Some reactor fuel cycles use beryllium, and its use and the associated hazards need further analysis. NRC-approved designs for transportation packages for shipping molten salt fuels and factory-built and fueled reactors are not available.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Technical Information Needs and Regulatory Considerations for Front-End Transportation Activities of HALEU Fuel Feed Material

This report fulfills task order number 31310022F0033 Task 1 Assessment of technical information needs and considerations for front-end transportation activities for HALEU fuel feed material. This assessment primarily focuses on the transportation outlook and packaging requirements for transporting high-assay low-enriched uranium (HALEU) fuel feed material. The regulatory framework is described in section 3.0. In section 4.0 the specific issues associated with reviewing HALEU feed material packages are discussed. The rest of the report discusses the need for new packages and Department of Energy progress on HALEU production. Through this evaluation it is shown that the 5% enrichment barrier between low-enriched uranium and HALEU is a significant challenge to transportation packaging. However, there are licensed designs and concepts that can be used to transport HALEU feedstock. No significant issues were identified through the HALEU range up to 20% enriched.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Temperature-Time Modeling of Spent Fuel Cladding in Dry Storage Casks

This report uses thermal and decay heat modeling to investigate spent fuel performance and the potential for cladding to anneal in dry storage conditions. Annealing is an important feature to investigate in SNF cladding because it has a direct relationship to cladding response in storage, transportation and disposal conditions. Annealed cladding may have lower strength than unannealed cladding, however its increased ductility would provide better protection against rupture in high strain rate situations such as severe accidents. These consequences are the driver for this work however are outside of the scope of this report. The modeling focused on three representative storage systems, the TN-32B, MAGNASTOR with TSC-37 canister, and NUHOMS AHSM with a 32PTH2 canister. This covers the vertical dual-purpose, vertical ventilated and horizontal ventilated casks respectively. Decay heat modeling using high and low enrichment assemblies was used to bound the decay heat curves that might be expected in dry storage. To bound the temperature relationship, the storage casks were modeled starting at the design basis heat loads with heat decaying through time. Although the results are bounding there is not an attempt to maximize conservatism, rather the intent to form a reasonable upper limit on temperature that will be broadly applicable to the U.S. cask fleet. This will allow materials testing to focus on relevant conditions for annealing that may affect the U.S. spent fuel inventory. The results show a clear dependence on heat load pattern in time in Figure S-1 and Figure S-2. This dependence is due to the different assembly decay heat curves for different assemblies in preferentially loaded casks. It shows the need for careful decay heat modeling when examining in service fuel temperatures that are less than the cask design basis heat load. The body of the report shows percent cladding cutoffs of 300°C and 350 °C as well. These results can be used to inform testing and conclusions about cladding performance through time and the potential for cladding annealing during dry storage.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

COBRA-SFS Version 6.2.1 User Guide: A Thermal Hydraulic Analysis Code for Spent Fuel Storage and Transportation Casks

This document is an updated and reduced version of the complete documentation of the COBRA-SFS thermal analysis code (COolant Boiling in Rod Arrays – Spent Fuel Storage) (Michener et al. 1995). This manual provides the analyst with input instructions and fundamental guidelines for contrasting models using COBRA-SFS. COBRA-SFS is designed to analyze the dry storage and transportation casks that house spent or used nuclear fuel. The primary focus and application is on square light water reactor fuel assemblies, however the code also has the capability to model hexagonal assemblies and is will suited to any geometry that can be defined as an extruded 2-D map.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Uncertainty in Thermal Modeling of Spent Nuclear Fuel Casks

Uncertainty is a key metric in computational modeling that must be evaluated for results to have wide ranging applicability. A well characterized uncertainty range is ideal with clear error bars on results that can be presented to stakeholders. In the field of spent fuel cask modeling, this ideal has been historically difficult to achieve in practice because of the computationally intensive nature of the models used and the difficulty assigning reasonable uncertainties to quantities in as-built systems. The work in this report has been conducted to evaluate the overall state of uncertainty and sensitivity in spent fuel cask models and develop methodologies for evaluating these uncertainties. These methodologies must be practical for engineering applications. They should not require excessive computational resources or calendar time to achieve results. In engineering, the model must be on a scale such that it can be changed and adapted throughout a project as new information is discovered and project goals evolve. This report covers three major modeling task areas that provide an overview of the types of sensitivity and uncertainty present in a spent fuel storage and transportation system. Section 3 discusses sensitivity and uncertainty analysis in the effective thermal conductivity model for the fuel region and applies these results to a single assembly model. Section 4 shows sensitivity analysis of a full cask model in the TN-32B and Section 5 demonstrates the overall uncertainty workflow using Coolant Boiling in Rod Arrays – Spent Fuel Storage and STAR-CCM+ developed from the sensitivity work in the preceding sections.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

FAST-1.1: Integral Assessment

An integral assessment has been performed to quantify the predictive capabilities of FAST, a thermal-mechanical nuclear fuel performance code designed to analyze fuel behavior from beginning of life to burnup levels allowed by the U.S. Nuclear Regulatory Commission (NRC). FAST code calculations are shown to compare satisfactorily to a preselected set of experimental data with both steady-state and anticipated operating occurrence (AOO) conditions and design basis accident (DBA) transient operating conditions. This document describes the assessment of FAST-1.1, the latest version of FAST, released April 2022. Abstract

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

TRANSIENT THERMAL MODELING OF THE HIGH BURNUP DEMONSTRATION RESEARCH PROJECT CASK USING STAR-CCM+ AND COBRA-SFS

The Department of Energy in collaboration with the Electric Power Research Institute is in the process of conducting the High Burnup Demonstration Project. Where the objective is to characterize the performance of high-burnup fuel in long term storage. As part of this demonstration, a TN-32B dry storage cask was instrumented and loaded with spent nuclear fuel at North Anna Nuclear Generating Station in November 2017. The project cask provides a unique opportunity to gain information on spent fuel and cask performance from an in-service operational system. The cask was instrumented with thermocouples inside of the fuel assemblies, then loaded and dried using normal procedures. After the drying process a thermal soak period where the cask was left indoors was used to obtain steady temperatures for model comparison along with surface temperatures. This paper details thermal modeling validation work that was done to model both the steady state and transient cases. Two modeling tools were used to predict temperatures in the cask. The general purpose CFD and heat transfer code STAR-CCM+ was used with both a detailed pin-by-pin model was used along with a more efficient k-effective simplification. The other code is COBRA-SFS, a purpose-built detailed thermal modeling tool developed and maintained at PNNL. Results from all the modeling tools were compared blind to the test data. Each model utilized general design information and compared reasonably well to the blind steady state data using convection and surface temperature boundary conditions. Post-test adjustments were later made to better reflect the “as built” conditions of the cask. Based on lessons learned from the steady state analysis the vacuum drying process was modeled in both codes. Utilizing the measured loading conditions the transient models were able to compare very well with the measured data. Overall the project showed an ability to model spent fuel storage conditions very well and future work is planned to generalize the methodology used for vacuum drying.

Thermal Analysis, Spent Fuel, Dry Storage↗

Sensitivity of Spent Fuel Temperatures to Variable Canister Backfills

This report describes thermal modeling done to understand the effects of a hypothetical loss of backfill to a spent fuel storage canister. A NAC MAGNASTOR system was analyzed using STAR-CCM+ and COBRA-SFS at various heat loads, helium pressures, and air environments. When helium was lost later in life the results showed no safety impact to the thermal performance of the cask system and fuel cladding. However, there were other results of interest from this study. The potential to detect helium leaks using external temperature measurement was considered and found to be a potential area for future technology development. The other major result of interest was the significant change in flow velocities with an air environment. This data will be useful in understanding the potential impacts of a breached canister.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Blind Modeling Validation Exercises Using the Horizontal Dry Cask Simulator

The U.S. Department of Energy (DOE) established a need to understand the thermal-hydraulic properties of dry storage systems for commercial spent nuclear fuel (SNF) in response to a shift towards the storage of high-burnup (HBU) fuel (> 45 gigawatt days per metric ton of uranium, or GWd/MTU). This shift raises concerns regarding cladding integrity, which faces increased risk at the higher temperatures within spent fuel assemblies present within HBU fuel compared to low-burnup fuel (≤ 45 GWd/MTU). A dry cask simulator (DCS) was built at Sandia National Laboratories (SNL) in Albuquerque, New Mexico to produce validation-quality data that can be used to test the accuracy of the modeling used to predict cladding temperatures. These temperatures are critical to evaluating cladding integrity throughout the storage cycle of commercial spent nuclear fuel. A model validation exercise was previously carried out for the DCS in a vertical configuration. Lessons learned during the previous validation exercise have been applied to a new, blind study using a horizontal dry cask simulator (HDCS). Three modeling institutions – the Nuclear Regulatory Commission (NRC), Pacific Northwest National Laboratory (PNNL), and Empresa Nacional del Uranio, S.A., S.M.E. (ENUSA) – were granted access to the input parameters from the DCS Handbook, SAND2017-13058R, and results from a limited data set from the horizontal BWR dry cask simulator tests reported in the HDCS update report, SAND2019-11688R. With this information, each institution was tasked to calculate peak cladding temperatures and air mass flow rates for ten HDCS test cases. Axial as well as vertical and horizontal transverse temperature profiles were also calculated. These calculations were done using modeling codes (ANSYS/Fluent, STAR-CCM+, or COBRA-SFS), each with their own unique combination of modeling assumptions and boundary conditions. For this validation study, the ten test cases of the horizontal dry cask simulator were defined by three independent variables – fuel assembly decay heat (0.5 kW, 1 kW, 2.5 W, and 5 kW), internal backfill pressure (100 kPa and 800 kPa), and backfill gas (helium and air). The plots provided in Chapter 3 of this report show the axial, vertical, and horizontal temperature profiles obtained from the dry cask simulator experiments in the horizontal configuration and the corresponding models used to describe the thermal-hydraulic behavior of this system. The tables provided in Chapter 3 illustrate the closeness of fit of the model data to the experiment data through root mean square (RMS) calculations of the error in peak cladding temperatures (PCTs), PCT axial locations, axial temperature profiles, vertical and horizontal temperature profiles at two different axial locations, and air mass flow rates for the ten test cases, normalized by the experimental results. The model results are assigned arbitrary model numbers to retain anonymity. Due to the relatively flat axial temperature profiles, small temperature gradients resulted in large deviations of all models’ PCT axial location from the experimental PCT axial location. When the PCT axial location error is excluded in the calculation of the combined RMS of the normalized errors that considers PCT, the temperature profiles, and the air mass flow rates, the model data fits the experimental data to within 5%. When the vault information is excluded, the model data fits the experimental data to within 2.5%. An error analysis was developed further for one model, using the model and experimental uncertainties in each validation parameter to calculate validation uncertainties. The uncertainties for each parameter were used to define quantifiable validation criteria. For this analysis, the model was considered validated for a given comparison metric if the normalized error in that metric divided by the validation uncertainty was less than or equal to 1. When considering the combined RMS of the normalized errors of all metrics divided by their validation uncertainties, the model was found to have satisfied the criterion for model validation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Thermal Analysis Evaluations Using the Dry Cask Simulator

Different thermal analysis models were developed to simulate the dry cask simulator (DCS). The DCS is an experiment designed to simulate dry storage of a single boiling water reactor fuel assembly under a variety of heat loads and internal pressures. The DCS was set up and tested in both a vertical and horizontal configuration to determine cladding temperatures in vertical and horizontal dry cask storage systems. The models included a detailed STAR-CCM+ model with the fuel assembly geometry explicitly modeled, a porous STAR-CCM+ model with the fuel assembly geometry modeled as porous media region with calculated effective properties, and a COBRA-SFS model. COBRA-SFS is a thermal-hydraulic code developed for steady-state and transient analysis of multi assembly spent-fuel storage and transportation systems. STAR-CCM+ is a commercial computation fluid dynamics (CFD) code. Both a detailed and porous STARCCM+ model were developed to look at the effective thermal conductivity (keff) approach to modeling a fuel assembly. A keff fuel model is typically model in CFD thermal analyses due to its significantly lower computational costs. The models were run for a combination of low and high canister pressures (100 kPa and 800 kPa) and low and high internal heat loads (0.5 kW and 5 kW). Results from all three models were compared against experimental data taken from the DCS for the peak cladding temperature (PCT) and inlet air mass flow.

Suffield, Sarah R.↗

FAST-1.0: Integral Assessment: Developed under NQA-1-2017

An integral assessment has been performed to quantify the predictive capabilities of FAST, a thermal-mechanical nuclear fuel performance code designed to analyze fuel behavior from beginning of life to burnup levels allowed by the U.S. Nuclear Regulatory Commission (NRC). FAST code calculations are shown to compare satisfactorily to a preselected set of experimental data with both steady-state, anticipated operating occurrence (AOO) and design basis transient operating conditions. This document describes the assessment of FAST-1.0, which is the latest version of FAST, released February 2020.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

High-Burnup Demonstration: Thermal Modeling of TN-32B Vacuum Drying and ISFSI Transients

This report describes thermal modeling done for the High-Burnup Spent Fuel Data Project that is being performed by the U.S. Department of Energy’s Spent Fuel and Waste Science and Technology research and development program. The purpose of this project is to investigate the performance of high-burnup spent nuclear fuel in dry storage. Part of this project is a demonstration test being performed with a storage module in the North Anna Nuclear Power Station’s Independent Spent Fuel Storage Installation (ISFSI). The storage module selected for this demonstration is an Orano TN-32B High-Burnup cask which has been loaded with fuel assemblies from the North Anna spent fuel pool.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Thermal Modeling of the TN-32B Cask for the High Burnup Spent Fuel Data Project

This report describes thermal modeling done for the High Burnup Dry Storage Research Project that is being performed by the U.S. Department of Energy’s Spent Fuel and Waste Science and Technology (SFWST) research and development (R&D) program. The purpose of this project to investigate the performance of high-burnup spent nuclear fuel in dry storage. Part of this project is a demonstration test being performed with a storage module in the North Anna Nuclear Power Station’s Independent Spent Fuel Storage Installation (ISFSI). The storage module selected for this demonstration is an Orano TN-32B High Burnup cask (Fig. S-1) which has been loaded with fuel assemblies from the North Anna spent fuel pool. The main goals of this test are to provide confirmatory data for model validation and potential improvement, support license renewals and new licenses for ISFSIs, and support transportation licensing for high burnup spent nuclear fuel (EPRI 2014).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

FRAPCON analysis of cladding performance during dry storage operations

There is an increasing need in the U.S. and around the world to move used nuclear fuel from wet storage in fuel pools to dry storage in casks stored at independent spent fuel storage installations (ISFSI) or interim storage sites. The NRC limits cladding temperature to 400°C while maintaining cladding hoop stress below 90 MPa in an effort to avoid radial hydride reorientation. An analysis was conducted with FRAPCON-4.0 on three modern fuel designs with three representative used nuclear fuel storage temperature profiles that peaked at 400 °C. Results were representative of the majority of U.S. LWR fuel. They conservatively showed that hoop stress remains below 90 MPa at the licensing temperature limit. Results also show that the limiting case for hoop stress may not be at the highest rod internal pressure in all cases but will be related to the axial temperature and oxidation profiles of the rods at the end of life and in storage.

Dry Storage↗

Thermal Modeling of a Loaded Magnastor Storage System at Catawba Nuclear Station

This report represents fulfillment of the M2 Milestone M2FT-16PN080203031, “High Heat Load Thermal Analyses,” under Work Package FT-16PN08020303. The report documents the analysis of the NAC International, Inc. (NAC) Modular, Advanced Generation, Nuclear All-purpose STORage (MAGNASTOR) module at Duke’s Catawba Nuclear Station. As part of the Used Fuel Disposition Campaign of the U.S. Department of Energy, a high-burnup fuel storage demonstration is planned for a storage module in the North Anna Nuclear Station’s Independent Spent Fuel Storage Installation (ISFSI). The storage module selected for this demonstration is an AREVA TN-32B High Burnup cask. The main goals of this proposed test are to provide confirmatory data for model validation and potential improvement, support license renewals and new licenses for ISFSIs, and support transportation licensing for high burnup spent nuclear fuel (EPRI 2014). The focus of the Demonstration test is the performance of the high-burnup fuel. To support the High Burnup Spent Fuel Data Project, Pacific Northwest National Laboratory (PNNL) staff performed a detailed thermal analysis (Fort et al. 2016) of the TN-32B cask. It was found that when conservatisms were removed from the thermal models and especially from the calculated decay heats, the predicted peak cladding temperatures (PCTs) were significantly below the 400°C (752°F) regulatory guidance limit, as specified in Interim Staff Guidance 11, Revision 3, (U.S. NRC 2003).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A Preliminary Evaluation of Using Fill Materials to Stabilize Used Nuclear Fuel During Storage and Transportation

This report contains a preliminary evaluation of potential fill materials that could be used to fill void spaces in and around used nuclear fuel contained in dry storage canisters in order to stabilize the geometry and mechanical structure of the used nuclear fuel during extended storage and transportation after extended storage. Previous work is summarized, conceptual descriptions of how canisters might be filled were developed, and requirements for potential fill materials were developed. Elements of the requirements included criticality avoidance, heat transfer or thermodynamic properties, homogeneity and rheological properties, retrievability, material availability and cost, weight and radiation shielding, and operational considerations. Potential fill materials were grouped into 5 categories and their properties, advantages, disadvantages, and requirements for future testing were discussed. The categories were molten materials, which included molten metals and paraffin; particulates and beads; resins; foams; and grout. Based on this analysis, further development of fill materials to stabilize used nuclear fuel during storage and transportation is not recommended unless options such as showing that the fuel remains intact or canning of used nuclear fuel do not prove to be feasible.

Storage↗