Search NASA⌕ Search

Engineering topics

Riedemann, Trevor

Publications and source records attributed to Riedemann, Trevor.

Synthesis and magnetic performance of gadolinium powder produced with rotating disk atomization

Spherical powder is key for achieving good heat transfer and maintaining low pressure drop for heat transfer fluid in magnetocaloric regenerator. Obtaining relatively large spherical powder of rare earth metals that are extremely sensitive to oxygen is challenging. Comparing to gas atomization and plasma rotating electrode methods, rotating disk atomization (RDA) method is more robust for obtaining a small amount of powder with a short turn-around time, thereby, more suitable for research and development of new magnetocaloric materials. In this work, commercially bulk gadolinium was successfully atomized to produce spherical powder in the targeted 150–250 μm range. The obtained powder exhibited the expected magnetocaloric performance with a maximum change of magnetic entropy of 12.1 J/kg K and a maximum adiabatic temperature change of 12.8 K with an applied magnetic field of 7 T.

36 MATERIALS SCIENCE↗

A deformation-processed Al-matrix/Ca-nanofilamentary composite with low density, high strength, and high conductivity

Light, strong materials with high conductivity are desired for many applications such as power transmission conductors, fly-by-wire systems, and downhole power feeds. However, it is difficult to obtain both high strength and high conductivity simultaneously in a material. In this study, an Al/Ca (20 vol%) nanofilamentary metal-metal composite was produced by powder metallurgy and severe plastic deformation. Fine Ca metal powders (~200 µm) were produced by centrifugal atomization, mixed with pure Al powder, and deformed by warm extrusion, swaging, and wire drawing to a true strain of 12.9. The Ca powder particles became fine Ca nanofilaments that reinforce the composite substantially by interface strengthening. The conductivity of the composite is slightly lower than the rule-of-mixtures prediction due to minor quantities of impurity inclusions. As a result, the elevated temperature performance of this composite was also evaluated by differential scanning calorimetry and resistivity measurements.

36 MATERIALS SCIENCE↗

Laser angle-resolved photoemission as a probe of initial state k z dispersion, final-state band gaps, and spin texture of Dirac states in the Bi 2 Te 3 topological insulator

Here, we have obtained angle-resolved photoemission (ARPES) spectra from single crystals of the topological insulator material Bi 2 Te 3 using tunable laser spectrometer. The spectra were collected for eleven different photon energies ranging from 5.57 to 6.70 eV for incident light polarized linearly along two different in-plane directions. Parallel first-principles, fully relativistic computations of photo-intensities were carried out using the experimental geometry within the framework of the one-step model of photoemission. Good overall accord between theory and experiment is used to gain insight into how properties of the initial and final state band structures as well as those of the topological surface states and their spin-textures are reflected in the laser-ARPES spectra. In conclusion, our analysis reveals that laser-ARPES is sensitive to both the initial state k z dispersion and the presence of delicate gaps in the final state electronic spectrum.

36 MATERIALS SCIENCE↗

Production of fine calcium powders by centrifugal atomization with rotating quench bath

Recently, a novel Al/Ca composite was produced by severe plastic deformation of Al powders and Ca granules for possible use as a high-voltage power transmission conductor. Since the strength of such composites is inversely proportional to the Ca filament size, fine Ca powders (less than ~250 μm) are needed to achieve the desired high strength for the powder metallurgy production of an Al-matrix composite reinforced by nano-scale Ca filaments. However, fine Ca powders are not commercially available. Therefore, we have developed a method to produce fine Ca powders via centrifugal atomization to supply Ca powder for prototype development of Al/Ca composite conductor. A secondary goal of the project was to demonstrate that Ca powder can be safely prepared, stored, and handled and could potentially be scaled for commercial production. Our results showed that centrifugal atomization can yield as much as 83 vol. % Ca powder particles smaller than 250 μm. The mean particle size sometimes matches, sometimes deviates substantially from the predictions of the Champagne & Anger equation likely due to unexpected secondary atomization. The particle size distribution is typical for a ligament-disintegration atomization mode. Scanning electron micrographs showed that the morphology of these Ca powders varied with powder size. Spark testing and auto-ignition tests indicated that the atomized powders were difficult to ignite, providing confidence that this material can be handled safely in air.

36 MATERIALS SCIENCE↗

Modeling the electrical resistivity of deformation processed metal-metal composites

Deformation processed metal–metal (matrix–reinforcement) composites (DMMCs) are high-strength, high-conductivity in situ composites produced by severe plastic deformation. The electrical resistivity of DMMCs is rarely investigated mechanistically and tends to be slightly higher than the rule-of-mixtures prediction. In this paper, we analyze several possible physical mechanisms (i.e. phonons, interfaces, mutual solution, grain boundaries, dislocations) responsible for the electrical resistivity of DMMC systems and how these mechanisms could be affected by processing conditions (i.e. temperature, deformation processing). As an innovation, we identified and assembled the major scattering mechanisms for specific DMMC systems and modeled their electrical resistivity in combination. From this analysis, it appears that filament coarsening rather than dislocation annihilation is primarily responsible for the resistivity drop observed in these materials after annealing and that grain boundary scattering contributes to the resistivity at least at the same magnitude as does interface scattering.

36 MATERIALS SCIENCE↗

Ames Lab 101: Lanthanum Decanting

Ames Laboratory scientist Trevor Riedemann explains the process that allows Ames Laboratory to produce some of the purest lanthanum in the world. This and other high-purity rare-earth elements are used to create alloys used in various research projects and play a crucial role in the Planck satellite mission.

36 MATERIALS SCIENCE↗