Search NASA⌕ Search

Engineering topics

Riley, Michael F.

Publications and source records attributed to Riley, Michael F..

10 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Improved first order approximation method for structural optimization

This paper examines various first order approximation methods commonly used in structural optimization. It considers several attempts at improving the approximation by using previous analytical results and introduces an adaptation of a first order approximation method using an exponent adjusted to better fit the constraints and reduce the overall number of iterations needed to attain the optimum.

Fadel, Georges M.↗
NASA NTRS1989

Integrated aerodynamic/dynamic optimization of helicopter rotor blades

An integrated aerodynamic/dynamic optimization procedure is used to minimize blade weight and 4 per rev vertical hub shear for a rotor blade in forward flight. The coupling of aerodynamics and dynamics is accomplished through the inclusion of airloads which vary with the design variables during the optimization process. Both single and multiple objective functions are used in the optimization formulation. The Global Criteria Approach is used to formulate the multiple objective optimization and results are compared with those obtained by using single objective function formulations. Constraints are imposed on natural frequencies, autorotational inertia, and centrifugal stress. The program CAMRAD is used for the blade aerodynamic and dynamic analyses, and the program CONMIN is used for the optimization. Since the spanwise and the azimuthal variations of loading are responsible for most rotor vibration and noise, the vertical airload distributions on the blade, before and after optimization, are compared. The total power required by the rotor to produce the same amount of thrust for a given area is also calculated before and after optimization. Results indicate that integrated optimization can significantly reduce the blade weight, the hub shear and the amplitude of the vertical airload distributions on the blade and the total power required by the rotor.

Chattopadhyay, Aditi↗
NASA NTRS1989

Integrated aerodynamic/dynamic optimization of helicopter rotor blades

An integrated aerodynamic/dynamic optimization procedure is used to minimize blade weight and 4/rev vertical shear of a rotor blade in forward flight. Both single and multiple objective functions are used, with constraints imposed on the first four coupled natural frequencies (elastic modes only), the blade aerorotational inertia, and the centrifugal stress. The global criteria approach is used for the multiple objective formulation, and the results are compared with those obtained from single objective function formulations. Optimum designs are compared against a reference blade, and it is shown that optimum results can be obtained in 7-10 cycles.

Chattopadhyay, Aditi↗
NASA NTRS1987

Application of formal optimization techniques in thermal/structural design of a heat-pipe-cooled panel for a hypersonic vehicle

Nonlinear mathematical programming methods are used to design a radiantly cooled and heat-pipe-cooled panel for a Mach 6.7 transport. The cooled portion of the panel is a hybrid heat-pipe/actively cooled design which uses heat pipes to transport the absorbed heat to the ends of the panel where it is removed by active cooling. The panels are optimized for minimum mass and to satisfy a set of heat-pipe, structural, geometric, and minimum-gage constraints. Two panel concepts are investigated: cylindrical heat pipes embedded in a honeycomb core and an integrated design which uses a web-core heat-pipe sandwich concept. The latter was lighter and resulted in a design which was less than 10 percent heavier than an all actively cooled concept. The heat-pipe concept, however, is redundant and can sustain a single-point failure, whereas the actively cooled concept cannot. An additional study was performed to determine the optimum number of coolant manifolds per panel for a minimum-mass design.

Camarda, Charles J.↗
NASA NTRS1987

Optimization methods applied to the aerodynamic design of helicopter rotor blades

Described is a formal optimization procedure for helicopter rotor blade design which minimizes hover horsepower while assuring satisfactory forward flight performance. The approach is to couple hover and forward flight analysis programs with a general-purpose optimization procedure. The resulting optimization system provides a systematic evaluation of the rotor blade design variables and their interaction, thus reducing the time and cost of designing advanced rotor blades. The paper discusses the basis for and details of the overall procedure, describes the generation of advanced blade designs for representative Army helicopters, and compares design and design effort with those from the conventional approach which is based on parametric studies and extensive cross-plots.

Walsh, Joanne L.↗
NASA NTRS1987

An evaluation of higher-order model methods for calculating transient structural response

A higher-order modal method proposed by Leung for transient structural analysis entitled the force-derivative method is evaluated. This method repeatedly integrates by parts with respect to time the convolution-integral form of the structural response to produce successively better approximations to the contribution of the higher modes which are neglected in the modal summation. Comparisons are made of the force-derivative, the mode-displacement, and the mode-acceleration methods for several numerical example problems for various times, levels of damping, and forcing functions. The example problems include a tip-loaded cantilevered beam and a simply-supported multispan beam. The force-derivative method is shown to converge to an accurate solution in fewer modes than either the mode-displacement or the mode-acceleration methods. In addition, for problems in which there are a large number of closely-spaced frequencies whose mode shapes have a negligible contribution to the response, the force-derivative method is very effective in representing the effect of the important, but otherwise neglected, higher modes.

Camarda, Charles J.↗
NASA NTRS1987

An evaluation of higher-order modal methods for calculating transient structural response

The present study evaluates a higher-order modal method proposed by Leung for transient structural analysis entitled the force-derivative method. This method repeatedly integrates by parts with respect to time the convolution-integral form of the structural response to produce successively better approximations to the contribution of the higher modes which are neglected in the modal summation. Comparisons are made of the force-derivative, the mode-displacement, and the mode-acceleration methods for several numerical example problems for various times, levels of damping, and forcing functions. The example problems include a tip-loaded cantilevered beam and a simply-supported multispan beam. The force-derivative method is shown to converge to an accurate solution in fewer modes than either the mode-displacement or the mode-acceleration methods. In addition, for problems in which there are a large number of closely-spaced frequencies whose mode shapes have a negligible contribution to the response, the force derivative method is very effective in representing the effect of the important, but otherwise neglected, higher modes.

Camarda, Charles J.↗