Engineering topics

Rincon, Rafael

Publications and source records attributed to Rincon, Rafael.

At least 19 records

NASA NTRS2019

Tri-Frequency Synthetic Aperture Radar for the Measurements of Snow Water Equivalent

A new airborne synthetic aperture radar (SAR) system was recently developed for the estimation of snow water equivalent (SWE). The radar is part of the SWESARR (Snow Water Equivalent Synthetic Aperture Radar and Radiometer) instrument, an active passive microwave system specifically designed for the accurate estimation of SWE. The dual polarization (VV, VH) radar operates at three frequency bands (9.65 GHz, 13.6 GHz, and 17.25 GHz), with bandwidths of up to 200 MHz. The radar flew its first flight campaign in November 2019, along with SWESARR’s - already operational – radiometer. The radar collected comprehensive data sets over various terrains that show a successful system performance. The inst slated to participate in future SnowEx campaigns.

Rincon, Rafael↗

NASA NTRS2019

Tri-Frequency Synthetic Aperture Radar for the Measurements of Snow Water Equivalent

SWESARR (Snow Water Equivalent Synthetic Aperture Radar and Radiometer) is an airborne instrument developed at the NASA Goddard Space Flight Center for the retrieval of Snow Water Equivalent. SWESARR was specifically designed to measure co-located active and passive signals using a high resolution and multi-frequency Synthetic Aperture Radar (SAR) and a multifrequency radiometer. SWESARR’s Synthetic Aperture Radar (SAR) system is made up of three independent radar units that operate in the X, Ku-Low, and Ku-High bands with bandwidths up to 200 MHz, and acquires data in two polarizations (dual-polarization radar). The difference in sensitivity of the backscatter signals to snow microstructure, in conjunctions with radiometer measurements, permits an accurate estimation of the snow water equivalent (SWE).

Rincon, Rafael↗

NASA NTRS2019

Adaptive Antenna Pattern Notching of Interference in Synthetic Aperture Radar Data Using Digital Beamforming

Radio Frequency Interference (RFI) is a growing problem in Synthetic Aperture Radar (SAR)systems as scientific motivations push the radars to lower frequencies and as more wireless services share the frequency spectrum. New, advanced SAR instruments, such as NASA's EcoSAR, DBSAR and DLR's Tandem-L mission, employ a multichannel architecture capable of Digital Beamforming (DBF). Radars with DBF are capable of notching the antenna pattern in specific directions, which can be utilized to suppress RFI on board or in post-processing. A well-researched beamformer for this purpose is the Minimum Variance Distortionless Response (MVDR) Beamformer. However, the number of interferers that can be removed through notching is limited by the number of receive channels. It is therefore essential to adaptively change the antenna pattern notching throughout the image in time and frequency for the best results with a given number of receive channels. In this paper, we present several methods to achieve this notching by making use of the spatial SAR signal distribution in range time, range frequency, azimuth time and azimuth Doppler that is inherent to the SAR imaging geometry. Because this distribution is time-variable and yet predictable, it can be used to improve the angle of arrival estimation of the RFI and the adaptive notching. The presented methods can be applied to a Digital Beamforming (DBF) SAR signal with multiple channels in elevation and/or in azimuth. Simulations show that the proposed methods increase the ability to notch out-of-swath interference from multiple directions and lessen the impact on in-swath interference. The improvement of the interferometric coherence for a single-pass interferogram acquired by NASA's EcoSAR system (capable of DBF in elevation) is demonstrated. The removal of periodic RFI artifacts is achieved.

RFI↗

NASA NTRS2018

Forest Structure Retrieval from Ecosar P-Band Single-Pass Interferometry

EcoSAR is a single-pass (dual antenna) digital beamforming, P-band radar system that is designed for remote sensing of dense forest structure. Forest structure retrievals require the measurement related to the vertical dimension, for which several techniques have been developed over the years. These techniques use polarimetric and interferometric aspects of the SAR data, which can be collected using EcoSAR. In this paper we describe EcoSAR system in light of its interferometric capabilities and investigate forest structure retrieval techniques.

Osmanoglu, Batuhan↗

NASA NTRS2018

Spaceborne P-Band MIMO SAR for Planetary Applications

The Space Exploration Synthetic Aperture Radar (SESAR) is an advanced P-band beamforming radar instrument concept to enable a new class of observations suitable to meet Decadal Survey science goals for planetary exploration. The radar operates at full polarimetry and fine (meter scale) resolution, and achieves beam agility through programmable waveform generation and digital beamforming. The radar architecture employs a novel low power, lightweight design approach to meet stringent planetary instrument requirements. This instrument concept has the potential to provide unprecedented surface and near-subsurface measurements applicable to multiple Decadal Survey Science Goals.

Rincon, Rafael↗

NASA NTRS2018

Miniaturized P-Band Beamforming Synthetic Aperture Radar Transceiver

The next generation synthetic aperture radar (SAR) instruments for the study of Earth and planets will employ multiple-input multiple output architectures and advanced beamforming techniques to significantly enhance the capabilities of remote sensing radars. One key component in realizing these instruments is a compact, lightweight and power efficient radar transceiver. To this end a P-band radar transceiver was developed to advance the technical readiness level (TRL) level toward spaceborne SAR instruments at the NASA Goddard Space Flight Center (GSFC).

Polarimetry↗

NASA NTRS2017

Next Generation P-Band Planetary Synthetic Aperture Radar

The Space Exploration Synthetic Aperture Radar (SESAR) is an advanced P-band beamforming radar instrument concept to enable a new class of observations suitable to meet Decadal Survey science goals for planetary exploration. The radar operates at full polarimetry and fine (meter scale) resolution, and achieves beam agility through programmable waveform generation and digital beamforming. The radar architecture employs a novel low power, lightweight design approach to meet stringent planetary instrument requirements. This instrument concept has the potential to provide unprecedented surface and near- subsurface measurements applicable to multiple Decadal Survey Science Goals.

P-band↗

NASA NTRS2017

Forest Structure Retrieval From EcoSAR P-Band Single-Pass Interferometry

SAR↗

NASA NTRS2017

RFI Detected in EcoSAR Data in the 430 - 440 MHz Band

Informational slides to be shared with colleagues at the the European Space Agency (ESA).

RFI↗

NASA NTRS2016

Digital Beamforming Synthetic Aperture Radar Developments at NASA Goddard Space Flight Center

Advanced Digital Beamforming (DBF) Synthetic Aperture Radar (SAR) technology is an area of research and development pursued at the NASA Goddard Space Flight Center (GSFC). Advanced SAR architectures enhances radar performance and opens a new set of capabilities in radar remote sensing. DBSAR-2 and EcoSAR are two state-of-the-art radar systems recently developed and tested. These new instruments employ multiple input-multiple output (MIMO) architectures characterized by multi-mode operation, software defined waveform generation, digital beamforming, and configurable radar parameters. The instruments have been developed to support several disciplines in Earth and Planetary sciences. This paper describes the radars advanced features and report on the latest SAR processing and calibration efforts.

Wide band↗

NASA NTRS2016

Next Generation P-Band Planetary Synthetic Aperture Radar

The Space Exploration Synthetic Aperture Radar (SESAR) is an advanced P-band beamforming radar instrument concept to enable a new class of observations suitable to meet Decadal Survey science goals for planetary exploration. The radar operates at full polarimetry and fine (meter scale) resolution, and achieves beam agility through programmable waveform generation and digital beamforming. The radar architecture employs a novel low power, lightweight design approach to meet stringent planetary instrument requirements. This instrument concept has the potential to provide unprecedented surface and near- subsurface measurements applicable to multiple DecadalSurvey Science Goals.

Wide band↗

NASA NTRS2016

Development of RFI Mitigation Techniques with Digital Beamforming

Remote sensing radars with longer wavelengths penetrate deeper into the observed scene and are more suitable for the scientific observation of ice sheets or vegetation. Therefore, SAR systems are moving to lower frequencies like L- or P-band. However, as the frequency spectrum is a limited resource, this means that the occupied frequency band has to be shared with existing users. These users can have serious impact on the imaging quality. Radio frequency interference (RFI) that arrives at the antenna together with the SAR backscatter is causing a drop of the signal-to-noise ratio. Despite the high processing gain of the SAR signal, artifacts can appear in the image if the RFI is strong enough. This can lead to a corruption of the acquired data and make it unsuitable for scientific purposes. Hence, the investigation of methods for RFI mitigation is critical to the performance of radar missions and to ensure they meet their main task.

Digital Beamforming↗

NASA NTRS2016

First Image Products from EcoSAR - Osa Peninsula, Costa Rica

Designed especially for forest ecosystem studies, EcoSAR employs state-of-the-art digital beamforming technology to generate wide-swath, high-resolution imagery. EcoSARs dual antenna single-pass imaging capability eliminates temporal decorrelation from polarimetric and interferometric analysis, increasing the signal strength and simplifying models used to invert forest structure parameters. Antennae are physically separated by 25 meters providing single pass interferometry. In this mode the radar is most sensitive to topography. With 32 active transmit and receive channels, EcoSARs digital beamforming is an order of magnitude more versatile than the digital beamforming employed on the upcoming NISAR mission. EcoSARs long wavelength (P-band, 435 MHz, 69 cm) measurements can be used to simulate data products for ESAs future BIOMASS mission, allowing scientists to develop algorithms before the launch of the satellite. EcoSAR can also be deployed to collect much needed data where BIOMASS satellite wont be allowed to collect data (North America, Europe and Arctic), filling in the gaps to keep a watchful eye on the global carbon cycle. EcoSAR can play a vital role in monitoring, reporting and verification schemes of internationals programs such as UN-REDD (United Nations Reducing Emissions from Deforestation and Degradation) benefiting global society. EcoSAR was developed and flown with support from NASA Earth Sciences Technology Offices Instrument Incubator Program.

InSAR↗

NASA NTRS2014

Development of NASA's Next Generation L-Band Digital Beamforming Synthetic Aperture Radar (DBSAR-2)

NASA's Next generation Digital Beamforming SAR (DBSAR-2) is a state-of-the-art airborne L-band radar developed at the NASA Goddard Space Flight Center (GSFC). The instrument builds upon the advanced architectures in NASA's DBSAR-1 and EcoSAR instruments. The new instrument employs a 16-channel radar architecture characterized by multi-mode operation, software defined waveform generation, digital beamforming, and configurable radar parameters. The instrument has been design to support several disciplines in Earth and Planetary sciences. The instrument was recently completed, and tested and calibrated in a anechoic chamber.

SAR↗

NASA NTRS2013

NASA Computational Case Study SAR Data Processing: Ground-Range Projection

Radar technology is used extensively by NASA for remote sensing of the Earth and other Planetary bodies. In this case study, we learn about different computational concepts for processing radar data. In particular, we learn how to correct a slanted radar image by projecting it on the surface that was sensed by a radar instrument.

Synthetic Aperture Radar (SAR)↗

NASA NTRS2013

Compact Radar Transceiver with Included Calibration

The Digital Beamforming Synthetic Aperture Radar (DBSAR) is an eight-channel phased array radar system that employs solid-state radar transceivers, a microstrip patch antenna, and a reconfigurable waveform generator and processor unit. The original DBSAR transceiver design utilizes connectorized electronic components that tend to be physically large and heavy. To achieve increased functionality in a smaller volume, PCB (printed circuit board) transceivers were designed to replace the large connectorized transceivers. One of the most challenging problems designing the transceivers in a PCB format was achieving proper performance in the calibration path. For a radar loop-back calibration path, a portion of the transmit signal is coupled out of the antenna feed and fed back into the receiver. This is achieved using passive components for stability and repeatability. Some signal also leaks through the receive path. As these two signal paths are correlated via an unpredictable phase, the leakage through the receive path during transmit must be 30 dB below the calibration path. For DBSAR s design, this requirement called for a 100-dB isolation in the receiver path during transmit. A total of 16 solid-state L-band transceivers on a PCB format were designed. The transceivers include frequency conversion stages, T/R switching, and a calibration path capable of measuring the transmit power-receiver gain product during transmit for pulse-by-pulse calibration or matched filtering. In particular, this calibration path achieves 100-dB isolation between the transmitted signal and the low-noise amplifier through the use of a switching network and a section of physical walls achieving attenuation of radiated leakage. The transceivers were designed in microstrip PCBs with lumped elements and individually packaged components for compactness. Each transceiver was designed on a single PCB with a custom enclosure providing interior walls and compartments to isolate transceiver subsystems from radiated interference. The enclosure also acts as a heat sink for the voltage regulators and power amplifiers inside the system. The PCB transceiver design produces transmit pulses of 2 W with an arbitrary duty cycle. Each transceiver is fed by an external 120-MHz signal transmit and two 1,140-MHz local oscillator signals. The received signal is amplified and down-converted to 120 MHz and is fed to the data processor. The transceiver dimensions are approximately 3.5 11.5 0.6 in. (9 29 1.5 cm). The PCB transceiver design reduces the volume and weight of the DBSAR instrument while maintaining the functionality found in the original design. Both volume and weight are critical for airborne and flight remote sensing instrumentation.

McLinden, Matthew↗

NASA NTRS2012

The 2011 Eco3D Flight Campaign: Vegetation Structure and Biomass Estimation from Simultaneous SAR, Lidar and Radiometer Measurements

The Eco3D campaign was conducted in the Summer of 2011. As part of the campaign three unique and innovative NASA Goddard Space Flight Center airborne sensors were flown simultaneously: The Digital Beamforming Synthetic Aperture Radar (DBSAR), the Slope Imaging Multi-polarization Photon-counting Lidar (SIMPL) and the Cloud Absorption Radiometer (CAR). The campaign covered sites from Quebec to Southern Florida and thereby acquired data over forests ranging from Boreal to tropical wetlands. This paper describes the instruments and sites covered and presents the first images resulting from the campaign.

Fatoyinbo, Temilola↗

NASA NTRS2007

RadSTAR L-Band Imaging Scatterometer: Performance Assessment

RadSTAR is an instrument development program aimed at combining a radiometer and a scatterometer system into a highly compact configuration that uses a single, electronically scanned antenna to provide co-located and simultaneous measurements of emission and backscatter for airborne and spaceborne applications [I]. The program was designed to map soil moisture and ocean salinity, both important components of the water cycle, and to map sea ice density and thickness, an important factor in ocean-atmosphere heat exchange in Polar Regions. The accuracy in estimation of these and a number of other Earth science parameters can be greatly enhanced by providing the co-aligned radar/radiometer microwave measurements. For instance, radiometer estimates of soil moisture from soil emission are affected by emission from vegetation, and from the roughness of the surface. Complementary measurements using the scatterometer can be used to evaluate the vegetation and surface roughness effects. Hence, the combined observations can provide an improved estimate. As with soil moisture, the ocean salinity is a function of the microwave emission from the sea surface temperature (SST) and sea roughness. There, the addition of radar backscatter measurements of sea roughness enables the correction of the emissivity and provide more accurate estimates of ocean salinity. Similar arguments can be made for other important Earth science parameters. This paper discusses the RadSTAR program, the radar system design, calibration, and digital beamforming techniques, and presents preliminary analysis of the data collected during the test flights. The data sets obtained during the flights and during the radar calibration in the anechoic chamber are also employed to asses the performance of the radar. The paper also discusses the Digital Beamforming Synthetic Aperture Radar (DBSAR) processor, a real-time processor recently developed for the LIS instrument which enables beam synthesis, fine resolutions, and large swaths.

Rincon, Rafael↗