Engineering topics

Rizk, Y. M.

Publications and source records attributed to Rizk, Y. M..

11 records

NASA NTRS1996

Computed Flow About The Integrated Space Shuttle, Revisited

Report discusses numerical simulations of flow of air about integrated space shuttle (complete space shuttle assembly including orbiter, solid rocket boosters, and external tank) in ascent. Updated version of report described in "Computed Flow About The Integrated Space Shuttle" (ARC-12685). Goal of studies to improve understanding of, and ability to predict how integrated space shuttle performs during both nominal and aborted ascent under various conditions.

Buning, P. G.↗

NASA NTRS1991

Computed Flow About The Integrated Space Shuttle

Report discusses numerical simulations of flow of air about integrated Space Shuttle in ascent. Goal: to improve understanding of, and ability to predict, how integrated Space Shuttle will perform during both nominal and aborted ascent under various conditions. These and other numerical simulations intended both to supplement wind-tunnel data, corrupted to some extent by scaling and wall-interference effects, and to compensate for scarcity of valid flight data.

Buning, P. G.↗

NASA NTRS1988

Numerical simulation of the integrated space shuttle vehicle in ascent

A simulation of the flow about the integrated space shuttle vehicle in ascent mode has been undertaken for various flight conditions using the Chimera composite grid discretization approach. Overset body-conforming grids were used to represent each geometric component, and an implicit approximately factored finite-difference procedure was used to solve the three-dimensional thin-layer Navier-Stokes equations. The computational results have been compared with both wind tunnel and flight test data. Although relatively good agreement is obtained with the experimental data, further refinement and evaluation of numerical error is under way.

Buning, P. G.↗

NASA NTRS1985

Use of a hyperbolic grid generation scheme in simulating supersonic viscous flow about three-dimensional winged configuration

The present paper describes a numerical mesh generation technique to be used with an implicit finite difference method for simulating visous supersonic flow about low-aspect-ratio wing body configurations using a single grid strategy. The computational domain is segmented into multiple regions, with borders located in supersonic areas to avoid the otherwise costly interfacing procedure between adjacent segments. The numerical procedure is applied to calculate the turbulent flow around the shuttle orbiter and a canard projectile at supersonic free stream Mach number.

Rizk, Y. M.↗

NASA NTRS1985

Generation of three-dimensional body-fitted coordinates using hyperbolic partial differential equations

An efficient numerical mesh generation scheme capable of creating orthogonal or nearly orthogonal grids about moderately complex three dimensional configurations is described. The mesh is obtained by marching outward from a user specified grid on the body surface. Using spherical grid topology, grids have been generated about full span rectangular wings and a simplified space shuttle orbiter.

Steger, J. L.↗

NASA NTRS1984

Viscous computation of a space shuttle flow field

A procedure is presented, as well as some results, to calculate the flow over the winged orbiter. This necessitates the use of two computer codes. A parabolized marching Navier-Stokes code is used to obtain the solution up to the bow shock-wing shock interaction region and for the region after the interaction. An unsteady Navier-Stokes code is to be used in the region of the shock interaction. Only resuls for the marching code are presented. For the flow conditions calculated, M infinity = 7.9, alpha = 25 deg, T(wall) = 540 R, Re(L) = 60728 per inch, laminar or turbulent, the PNS code was marched up to an X/L = 0.7 which is where the bow shock-wing shock interaction region occurs.

Chaussee, D. S.↗

NASA NTRS1983

Calculation of viscous supersonic flows over finned bodies

The parabolized Navier-Stokes (PNS) equations are used to calculate the viscous, supersonic flow fields about a six-finned projectile and a generic four-finned missile at angles of attack. Since current computer speeds and storage preclude a fully three-dimensional calculation using the unsteady, Reynolds-averaged, Navier-Stokes equations, the applicability of the PNS equations to the above flow fields is of considerable interest. Two important aspects of the calculation are grid generation and the type of smoothing used to prevent nonphysical solutions. This paper includes a description of the grid-generation process. Results in the form of density contours and velocity vector plots are presented for the two configurations. The applicability of the PNS equations to the complicated flow fields considered is successfully demonstrated.

Rai, M. M.↗

NASA NTRS1983

Three-dimensional viscous-flow computations using a directionally hybrid implicit-explicit procedure

A new, directionally dependent, hybrid numerical algorithm for solving the unsteady, three-dimensional Navier-Stokes equations has been developed and used to compute the viscous supersonic flow over complex configurations, which may generate local regions of embedded subsonic or streamwise separated flows or both. The new hybrid implicit-explicit algorithm is derived from the more general implicit Beam-Warming algorithm and is particularly suitable for viscous computations in which the grid spacing in the direction outward from the body is considerably smaller than the spacing in the other two directions. Numerical results obtained from both the hybrid and implicit schemes are presented and compared on the basis of numerical stability, convergence history, and computer and core memory requirements.

Rizk, Y. M.↗

NASA NTRS1982

Computation of viscous hypersonic flow over control surfaces

A parabolized Navier-Stokes (PNS) computer code has been used to compute hypersonic flow over control surfaces located on the aft end of generic re-entry configurations. The Beam-Warming implicit numerical algorithm as modified by Schiff and Steger is used to march in the spatial direction. The outer bow shock is treated as a sharp discontinuity; within the shock layer discontinuities are captured. Several different turbulent flow solutions were generated for flap angles varying from -7 deg to 15 deg and angles of attack varying from 0 deg to 20 deg. The present results are qualitatively correct when compared with previous compression corner studies.

Chaussee, D. S.↗

NASA NTRS1982

Numerical simulation of viscous-inviscid interactions on indented nose tips

An implicit numerical algorithm to solve the unsteady thin-layer Navier-Stokes equations in a strong conservative form has been used to compute the viscous flow over indented nose tips placed in a supersonic free stream. Numerical solutions are presented for axisymmetric and three-dimensional indented configurations for laminar flow conditions. Results demonstrate the capability of the present numerical procedure to predict flow fields that contain strong viscous-inviscid interactions, including boundary-layer separation, reattachment, and embedded discontinuities. Comparisons with available experimental data for the shock shape and surface pressure are also given.

Rizk, Y. M.↗

NASA NTRS1981

Computation of hypersonic viscous flow around three-dimensional bodies at high angles of attack

A parabolized Navier-Stokes code capable of predicting steady viscous supersonic flows with cross-flow separation is applied to three-dimensional arbitrary geometries at high angles of attack. The numerical procedure, which is implicit, noniterative, and of second-order accuracy in the marching direction, has been used to compute complicated flow fields containing a relatively thick sonic layer and regions of strong viscous-inviscid interaction. A consistent and accurate procedure has also been developed to provide the necessary starting data through timewise integration of the equations of motion near the nose-tip region of the body. Numerical results obtained from the present method compare well with experiment for both the surface pressures and heat transfer.

Rizk, Y. M.↗