Engineering topics

Roberts, Benjamin Q.

Publications and source records attributed to Roberts, Benjamin Q..

7 records

DOE OSTI2024

Characterizing Interference in a Wave-Powered Buoy

Oceanographic measurement buoys are power constrained by the capacity of their batteries and the available solar power. Many buoys are in locations with abundant wave energy, but wave energy converters are not being used to power them. One reason wave energy converters may not have not been developed for wave measurement buoys is that many buoys measure waves by precisely following the wave motion. Wave energy converters may inhibit this wave-following ability by altering a buoy's response to incoming waves. In this report, we present the results of field tests that measured the extent to which buoy motion was changed by modifications to the buoy for wave energy harvesting. The motion of the buoy was significantly modified by the addition of the hardware components necessary for harvesting wave energy. The ratio of the mass of the wave energy converter to the mass of the buoy was high for the system tested, which strongly affected buoy motion. A lower value for this ratio would decrease the effect of the wave energy converter on the motion of the buoy, thereby decreasing the impact on the buoy's ability to measure waves but also decreasing the power production capabilities. Therefore, the use of wave energy converters to power wave measurement buoys may be feasible for large buoys that measure low-frequency waves and have low power requirements.

16 TIDAL AND WAVE POWER↗

DOE OSTI2023

Hardware-in-the-Loop Efficiency Analysis of Tidal Power Systems

Marine renewable energy presents an opportunity for sustainable power in areas located near and in the marine environment. In particular, tidal energy offers a consistent and reliable resource. However, tidal energy harvesting systems seeking to take advantage of this resource face challenges associated with power electronics. Power conversion electronics struggle with low efficiencies, lack of off-the-shelf options for small-scale energy harvesting systems, and limited opportunities for testing with deployed turbines. This work demonstrates a hardware-in-the-loop experimental design and methodology for characterizing efficiency of tidal turbine power electronics and control methods. The suggested method removes barriers to testing these power electronics by eliminating the need for a physical tidal turbine and generator to produce accurate harvested tidal power profiles.

tidal turbine, hardware-in-the-loop, energy conver↗

DOE OSTI2022

Real-Time Seismic System for Monitoring, Imaging, and Characterization (RT-SEISMIC)

The goal of this Laboratory Directed Research and Development (LDRD) project was to develop a borehole seismic source and sensor array to enable real-time seismic imaging at scales and conditions relevant to the energy industry including both fossil-energy and geothermal. In FY21 and FY22, we designed, built, and tested both a prototype impulse source module for generating seismic energy and a sensing module for recording ground motions generated by the source module array. A pneumatically driven vibratory source was also designed. The source modules were fabricated with all high temperature components and the team has worked to incorporate the current RT-SEISMIC electronics design into a commercially available, high temperature silicon-on-insulator chip integrated circuit. Several issues were identified during fabrication and lab testing that led to redesign of several system components and subsequent retesting. The final round of testing showed that while metal/graphite-based seals worked quite well for static seals, they were unable to provide an adequate gas seal for dynamic, reciprocating part movements which necessitated a final redesign using Kalrez. This change will result in a continuous temperature rating of approximately 275 degrees C for the system. While a field test of the RT-SEISMIC system was targeted in FY22, due to the extended lab testing and redesign efforts, field testing was not achieved. As a result of this LDRD investment, several sponsors have expressed interest in RT-SEISMIC and we expect to continue towards a field demonstration of the full system in the future.

58 GEOSCIENCES↗

DOE OSTI2021

Modeling heat transport processes in enhanced geothermal systems: Validation study from EGS Collab Experiment 1

Heat recovery from enhanced geothermal systems (EGS) is a complex process involving heat transport in both fracture networks and rock formations. A comprehensive understanding of and the ability to model the underlying heat transport mechanisms is important for the success of EGS but remains challenging in practice due to the generally insufficient characterization of EGS reservoirs. In the present study, we analyze an extensively monitored intermediate-scale EGS field experiment performed in a well-characterized testbed. The high-resolution, high-quality measurements from the field experiment enable the development of a high-fidelity model incorporating a well-constrained fracture network. Based on the field experiment, we investigate the complex heat transport processes in an EGS-relevant environment and validate the capability of a numerical approach in simulating these inherently coupled heat transport processes. A series of numerical simulations were performed to study the effects of different heat transport mechanisms, including thermal convection with fracture flow, thermal conduction in rock formations, and the Joule-Thomson effect. The agreement of thermal responses between field measurements and simulation results indicates that our numerical approach can appropriately model the heat transport processes pertaining to heat recovery from EGS reservoirs.

Wu, Hui↗

DOE OSTI2020

In Situ Catalytic Fast Pyrolysis using Red Mud Catalyst: Impact of catalytic fast pyrolysis temperature and biomass feedstocks

Catalytic fast pyrolysis (CFP) has been considered as a very promising approach for converting lignocellulosic biomass into higher-quality bio-oils followed by hydrotreating to produce fuelrange products. A reactive, robust, and low-cost catalyst is required to drive the CFP process. Red mud, a side-product produced during the refining of bauxite to alumina, appears to be an effective catalyst for in situ CFP of biomass. In this paper, we report the impact of CFP reaction temperature on the conversion of a pinyon juniper feedstock to bio-oils using red mud as the catalyst and then to fuel-range hydrocarbons by hydrotreating of the produced bio-oil. The yield and quality of the CFP bio-oil produced and the yield and quality of hydrotreated final products were determined. When the CFP process temperature was lowered from 450 to 400ºC, the bio-oil yield increased with minimal differences in the oxygen content, hydrogen-to-carbon ratio, water content, etc. In addition, CFP bio-oils at both temperatures were processed in a single-stage continuous hydrotreater without reactor plugging during the testing period (i.e., ~100 hours on stream). The yield of CFP bio-oil produced at 400ºC was lower than the yield at 450ºC. However, the overall yield, from biomass to hydrocarbon fuel, was still higher for CFP processing at 400ºC than for processing at 450ºC. This indicates the potential for enhancing overall carbon efficiency, including CFP processing and hydrotreating, by employing red mud catalysts for biomass pyrolysis and tuning the CFP parameters. Detailed analysis of bio-oil and hydrotreated products showed a lower content of lignin-derived species in both samples. Furthermore, CFP processing of three different biomass feedstocks corroborated red mud catalyst development for producing improved quality bio-oil and, when combined with hydrotreating, for the production of fuel range hydrocarbons.

Santosa, Daniel M.↗

DOE OSTI2018

Advanced Monitoring Systems for Deep Vadose Zone Applications Interim Status Report

The vadose zone within the Hanford Central Plateau contains large quantities of mobile contaminants that have not yet reached the groundwater. Deep vadose zone (DVZ) contamination is located below the depth of direct contaminant exposure potential, but may be a current and/or potential future source of groundwater contamination. Monitoring to observe subsurface processes and driving forces related to contaminant transport or to directly observe contaminant movement in the DVZ provide remedy performance information prior to contaminants reaching the groundwater and thereby are important elements of a remedy implementation.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2018

Heavy fossil hydrocarbon conversion and upgrading using radio-frequency or microwave energy

Conversion of heavy fossil hydrocarbons (HFH) to a variety of value-added chemicals and/or fuels can be enhanced using microwave (MW) and/or radio-frequency (RF) energy. Variations of reactants, process parameters, and reactor design can significantly influence the relative distribution of chemicals and fuels generated as the product. In one example, a system for flash microwave conversion of HFH includes a source concentrating microwave or RF energy in a reaction zone having a pressure greater than 0.9 atm, a continuous feed having HFH and a process gas passing through the reaction zone, a HFH-to-liquids catalyst contacting the HFH in at least the reaction zone, and dielectric discharges within the reaction zone. The HFH and the catalyst have a residence time in the reaction zone of less than 30 seconds. In some instances, a plasma can form in or near the reaction zone.

Strohm, James J.↗