Search NASA⌕ Search

Engineering topics

Roberts, Leonard

Publications and source records attributed to Roberts, Leonard.

32 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Numerical study of the effect of tangential leading edge blowing on delta wing vortical flow

A numerical simulation of tangential blowing along the leading edge of a delta wing is analyzed as a means of controlling the position and strength of the leading-edge vortices. The computation is done by numerical solutions of the three-dimensional thin-layer Navier-Stokes equations. Numerical results are shown to compare favorably with experimental measurements. It is found that the use of tangential leading-edge blowing at low to moderate angles of attack tends to reduce the pressure peaks associated with leading-edge vortices and to increase the suction peak around the leading edge, such that the integrated value of the surface pressure remains about the same.

Yeh, David T.↗
NASA NTRS1988

An experimental study of an adaptive-wall wind tunnel

A series of adaptive wall ventilated wind tunnel experiments was carried out to demonstrate the feasibility of using the side wall pressure distribution as the flow variable for the assessment of compatibility with free air conditions. Iterative and one step convergence methods were applied using the streamwise velocity component, the side wall pressure distribution and the normal velocity component in order to investigate their relative merits. The advantage of using the side wall pressure as the flow variable is to reduce the data taking time which is one the major contributors to the total testing time. In ventilated adaptive wall wind tunnel testing, side wall pressure measurements require simple instrumentation as opposed to the Laser Doppler Velocimetry used to measure the velocity components. In ventilated adaptive wall tunnel testing, influence coefficients are required to determine the pressure corrections in the plenum compartment. Experiments were carried out to evaluate the influence coefficients from side wall pressure distributions, and from streamwise and normal velocity distributions at two control levels. Velocity measurements were made using a two component Laser Doppler Velocimeter system.

Celik, Zeki↗
NASA NTRS1988

Numerical study of delta wing leading edge blowing

Spanwise and tangential leading edge blowing as a means of controlling the position and strength of the leading edge vortices are studied by numerical solution of the three-dimensional Navier-Stokes equations. The leading edge jet is simulated by defining a permeable boundary, corresponding to the jet slot, where suitable boundary conditions are implemented. Numerical results are shown to compare favorably with experimental measurements. It is found that the use of spanwise leading edge blowing at moderate angle of attack magnifies the size and strength of the leading edge vortices, and moves the vortex cores outboard and upward. The increase in lift primarily comes from the greater nonlinear vortex lift. However, spanwise blowing causes earlier vortex breakdown, thus decreasing the stall angle. The effects of tangential blowing at low to moderate angles of attack tend to reduce the pressure peaks associated with leading edge vortices and to increase the suction peak around the leading edge, so that the integrated value of the surface pressure remains about the same. Tangential leading edge blowing in post-stall conditions is shown to re-establish vortical flow and delay vortex bursting, thus increasing C sub L sub max and stall angle.

Yeh, David↗
NASA NTRS1988

Navier Stokes computation of the flow field over delta wings with spanwise leading edge blowing

The concept of spanwise leading edge blowing, a means of controlling the position and strength of leading edge vortices, is analyzed by numerical solutions of the three-dimensional Thin-Layer Navier Stokes equations. The leading edge jet is simulated by defining a permeable boundary, corresponding to the jet slot, where suitable boundary conditions are implemented. Numerical results agree favorably with experimental measurements. It is found that the use of spanwise leading edge blowing not only magnifies the size and strength of the leading edge vortices, but also moves the vortex cores outboard and upward. As a result, the increase in lift comes primarily from the greater nonlinear vortex lift. The presence of the leading edge jet stream displaces the flow outboard, thereby increasing the effective aspect ratio of the delta wing. However, blowing causes earlier vortex breakdown, thus decreasing the stall angle.

Yeh, David T.↗
NASA NTRS1987

Control of vortical separation on conical bodies

In a variety of aeronautical applications, the flow around conical bodies at incidence is of interest. Such applications include, but are not limited to, highly maneuverable aircraft with delta wings, the aerospace plane and nose portions of spike inlets. The theoretical model used has three parts. First, the single line vortex model is used within the framework of slender body theory, to compute the outer inviscid field for specified separation lines. Next, the three dimensional boundary layer is represented by a momentum equation for the cross flow, analogous to that for a plane boundary layer; a von Karman Pohlhausen approximation is applied to solve this equation. The cross flow separation for both laminar and turbulent layers is determined by matching the pressure at the upper and lower separation points. This iterative procedure yields a unique solution for the separation lines and consequently for the position of the vortices and the vortex lift on the body. Lastly, control of separation is achieved by blowing tangentially from a slot located along a cone generator. It is found that for very small blowing coefficients, the separation can be postponed or suppressedy completely.

Mourtos, Nikos J.↗
NASA NTRS1987

A computational study of thrust augmenting ejectors based on a viscous-inviscid approach

A viscous-inviscid interaction technique is advocated as both an efficient and accurate means of predicting the performance of two-dimensional thrust augmenting ejectors. The flow field is subdivided into a viscous region that contains the turbulent jet and an inviscid region that contains the ambient fluid drawn into the device. The inviscid region is computed with a higher-order panel method, while an integral method is used for the description of the viscous part. The strong viscous-inviscid interaction present within the ejector is simulated in an iterative process where the two regions influence each other en route to a converged solution. The model is applied to a variety of parametric and optimization studies involving ejectors having either one or two primary jets. The effects of nozzle placement, inlet and diffuser shape, free stream speed, and ejector length are investigated. The inlet shape for single jet ejectors is optimized for various free stream speeds and Reynolds numbers. Optimal nozzle tilt and location are identified for various dual-ejector configurations.

Lund, Thomas S.↗
NASA NTRS1987

A theory for turbulent curved wall jets

An attempt is made to formulate the simplest possible model for the flow of a wall jet emanating from a two dimensional source into quiescent surroundings in the presence of a wall of arbitrary shape. The method used self similar profiles for the mean velocity together with a simple eddy viscosity model. The streamwise and radial momentum equations are integrated across the wall jet flow to give an expression for the momentum balance including the effect of the pressure gradient induced by the rate of change of surface curvature. The streamwise momentum equation is also evaluated at the point of maximum velocity to provide a second equation and thereby permit a solution for the two unknown quantities, the jet half width and the maximum velocity. This approach provides approximate closed form solutions for the flow of the wall jet over surfaces of various shapes, and in particular permits a direct comparison with the available experimental results for plane, cylindrical or logarithmic spiral surfaces.

Roberts, Leonard↗
NASA NTRS1986

A theory for turbulent curved wall jets

A simple theoretical model is proposed to describe the flow of a turbulent wall jet along a curved surface into a quiescent atmosphere. An integral method is used to solve the momentum equation and identifies three contributions to the spreading rate of the wall jet: (1) turbulent diffusion in the wall jet; (2) wall curvature; and (3) rate of change of wall curvature. Closed from approximate solutions are found for the case of a plane wall, a circular cylinder, and a logarithmic spiral surface. Comparison with experimental data for these three cases is made showing good agreement.

Roberts, Leonard↗
NASA NTRS1960

An Analysis of Ablation-Shield Requirements for Manned Reentry Vehicles

The problem of sublimation of material and accumulation of heat in an ablation shield is analyzed and the results are applied to the reentry of manned vehicles into the earth's atmosphere. The parameters which control the amount of sublimation and the temperature distribution within the ablation shield are determined and presented in a manner useful for engineering calculation. It is shown that the total mass loss from the shield during reentry and the insulation requirements may be given very simply in terms of the maximum deceleration of the vehicle or the total reentry time.

Roberts, Leonard↗
NASA NTRS1959

Mass Transfer Cooling Near The Stagnation Point

A simplified analysis is made of mass transfer cooling, that is, injection of a foreign gas, near the stagnation point for two-dimensional and axisymmetric bodies. The reduction in heat transfer is given in terms of the properties of the coolant gas and it is shown that the heat transfer may be reduced considerably by the introduction of a gas having appropriate thermal and diffusive properties. The mechanism by which heat transfer is reduced is discussed.

Roberts, Leonard↗
NASA NTRS1959

A Theoretical Study of Stagnation-Point Ablation

A simplified analysis is made of ablation cooling near the stagnation point of a two-dimensional or axisymmetric body which occurs as the body vaporizes directly from the solid state. The automatic shielding mechanism Is discussed and the important thermal properties required by a good ablation material are given. The results of the analysis are given in terms of dimensionless parameters.

Roberts, Leonard↗
NASA NTRS1959

Stagnation-Point Shielding by Melting and Vaporization

An approximate theoretical analysis was made of the shielding mechanism whereby the rate of heat transfer to the forward stagnation point of blunt bodies is reduced by melting and evaporation. General qualitative results are given and a numerical example, the melting and evaporation of ice, is presented and discussed in detail.

Roberts, Leonard↗