Engineering topics

Roberts, W. B.

Publications and source records attributed to Roberts, W. B..

10 records

NASA NTRS1985

Modeling the 3-D flow effects on deviation angle for axial compressor middle stages

A model of the spanwise variation of the three-dimensional flow effects on deviation is proposed for middle-stage rotors and stators. This variation is taken as the difference above or below that predicted by blade element theory at any spanwise location. It was found that the stator variation is strongly affected by the end-wall boundary-layer thickness as well as camber, solidity, and blade channel aspect ratio. Rotor variation was found to depend on end-wall boundary layer thickness and tip clearance normalized by blade span. If these parameters are known or can be calculated, the models provide a reasonable approximation to the spanwise variation of deviation for middle compressor stages operating at low to high subsonic inlet Mach numbers.

Roberts, W. B.↗

NASA NTRS1984

Secondary flow spanwise deviation model for the stators of NASA middle compressor stages

A model of the spanwise variation of deviation for stator blades is presented. Deviation is defined as the difference between the passage mean flow angle and the metal angle at the outlet of a blade element of an axial compressor stage. The variation of deviation is taken as the difference above or below that predicted by blade element, (i.e., two-dimensional) theory at any spanwise location. The variation of deviation is dependent upon the blade camber, solidity and inlet boundary layer thickness at the hub or tip end-wall, and the blade channel aspect ratio. If these parameters are known or can be calculated, the model provides a reasonable approximation of the spanwise variation of deviation for most compressor middle stage stators operating at subsonic inlet Mach numbers.

Roberts, W. B.↗

NASA NTRS1982

An experimental investigation of internal area ruling for transonic and supersonic channel flow

A simulated transonic rotor channel model was examined experimentally to verify the flow physics of internal area ruling. Pressure measurements were performed in the high speed wind tunnel at transonic speeds with Mach 1.5 and Mach 2 nozzle blocks to get an indication of the approximate shock losses. The results showed a reduction in losses due to internal area ruling with the Mach 1.5 nozzle blocks. The reduction in total loss coefficient was of the order of 17 percent for a high blockage model and 7 percent for a cut-down model.

Roberts, W. B.↗

NASA NTRS1980

Off-design correlation for losses due to part-span dampers on transonic rotors

Experimental data from 10 transonic fan rotors were used to correlate losses created by part-span dampers located near the midchord position on the rotor blades. The design tip speed of these rotors varied from 419 to 425 m/sec, and the design pressure ratio varied from 1.6 to 2.0. Additional loss caused by the dampers for operating conditions between 50 and 100 percent of design speed were correlated with relevant aerodynamic and geometric parameters. The resulting correlation predicts the variation of total-pressure-loss coefficient in the damper region to a good approximation.

Roberts, W. B.↗

NASA NTRS1979

An off-design correlation of part span damper losses through transonic axial fan rotors

The experimental performance of 10 transonic fan rotors was used to correlate losses caused by midchord part-span dampers (PSD) during off-design operation between 50 and 100 percent of design speed. The design tip speed for the rotors used varied from 419 to 425 m/s and the design pressure ratios from 1.6 to 2.0. The loss attributable to the damper and the region influenced along the blade height was correlated with relevant aerodynamic and geometric parameters. The losses at the design point were estimated by a previously reported correlation (Roberts, 1978). Using this as a base, the off-design losses were correlated with variation in blade suction surface incidence. A check with independent data showed that the prediction of damper losses and region of influence was fair to good for most of the off-design data examined.

Roberts, W. B.↗

NASA NTRS1979

Low-turbulence high-speed wind tunnel for the determination of cascade shock losses

A low turbulence high-speed wind tunnel, using anti-turbulence screening and a 100:1 contraction ratio, has been found suitable for high-speed smoke flow visualization. The location and strength of normal, oblique, and curved shock waves generated by transonic or supersonic wind tunnel flow over airfoils or through axial compressor cascades is determined by combined shadowgraph and smokelines visualization techniques without the interference effects caused by intrusive probes. The Reynolds number based on chord varied between 50,000 and 1,000,000. Preliminary results are compared with the relevant theory and data gathered using a total pressure probe.

Slovisky, J. A.↗

NASA NTRS1979

High speed smoke flow visualization for the determination of cascade shock losses

A flow visualization technique has been developed by which quantitative cascade shock loss data can be ascertained without the interference effects of intrusive probes. The technique is first proven feasible by studying the high speed wind tunnel flow around a variety of two-dimensional shapes. Applicability is demonstrated by the testing of a 5% thick sharp-edged flat plate cascade at an upstream Mach number of about 1.3. Results are compared with the relevant theory and total pressure probe data.

Slovisky, J. A.↗

NASA NTRS1978

A design point correlation for losses due to part-span dampers on transonic rotors

The design-point losses caused by part-span dampers were correlated for 21 transonic axial-flow fan rotors that had tip speeds varying from 350 to 488 meters per second and design pressure ratios of 1.5 to 2.0. The additional loss attributable to the damper and the total region along the blade height influenced were correlated with selected aerodynamic and geometric parameters. The maximum damper loss correlated well with the mean inlet Mach number at the damper location, the geometric parameters of leading- and trailing-edge damper radius normalized by mean passage height and damper aerodynamic chord, respectively, and the aerodynamic loading parameter of the blade camber divided by the solidity at the damper location. The region of damper influence extended over a mean passage height of the order of 10 to 15 times the maximum damper thickness.

Roberts, W. B.↗

NASA NTRS1978

A study of axial compressor blade optimization for operation in the low Reynolds number regime

Original and previously published experimental data is presented in this study of axial compressor blade optimization for use in the subcritical Reynolds number region. Three methods of increasing cascade performance at these low Rc are presented, discussed, and compared: (1) use of sharp-leading-edge profiles, (2) trip wires or roughness elements, and (3) high free-stream turbulence. The original data was collected in the VKI C-1 cascade wind tunnel; during these tests blade chord Reynolds number was varied from 250,000 down to about 17,000. Each technique demonstrated an increase in low Reynolds number (based on chord) performance for certain profiles, with the sharp-leading-edge profile as the potential optimum. Axial compressors or pumps that must operate for a significant amount of their design life under low Reynolds number conditions might benefit substantially from these methods.

Roberts, W. B.↗

NASA NTRS1977

Correlation of part-span damper losses through transonic rotors operating near design point

The design-point losses caused by part-span dampers (PSD) were correlated for 21 transonic axial flow fan rotors that had tip speeds varying from 350 to 488 meters per second and design pressure ratios of 1.5 to 2.0. For these rotors a correlation using mean inlet Mach number at the damper location, along with relevant geometric and aerodynamic loading parameters, predicts the variation of total pressure loss coefficient in the region of the damper to a good approximation.

Roberts, W. B.↗