Search NASA⌕ Search

Engineering topics

Robertson, John

Publications and source records attributed to Robertson, John.

Repairing High γ’ Hot Section Gas Turbine Components Using Advanced Manufacturing

This article describes the ability to use laser-blown powder deposition to repair high γ' IN-100 superalloy gas turbine components. The influence of various process conditions on the ability to make crack-free IN-100 deposits over surrogate high γ' alloys was investigated to identify cracking mechanisms in the deposit and heat-affected zones (HAZs). The various crack formation mechanisms, such as solidification cracking and liquation cracking, were evaluated using multiscale characterization and numerical simulation. The cracking in the deposit region was predominantly solidification cracking, while those observed in the HAZ were liquation cracking. The results showed that controlling thermally induced residual stresses is the key to eliminating cracking, and the optimum preheat temperature was determined. In conclusion, the results were then contrasted with those in published literature and an approach to effectively repair hot section parts was presented.

36 MATERIALS SCIENCE↗

Field testing of a spectrum-splitting transmissive concentrator photovoltaic module

Hybrid photovoltaic-thermal systems can decouple IR light from visible light, allowing it to be collected separately by spectrum-optimized mechanisms for increased total efficiency. To demonstrate this, we have designed and prototyped a transmissive spectrum-splitting concentrator photovoltaic module that maximizes solar energy conversion by utilizing the entire solar spectrum. The system first collects visible light using IR-transmissive triple-junction photovoltaic cells to achieve an in-band module efficiency of η m I B = 34.7% for light of wavelengths λ < 870 nm. Simultaneously, 58.8% of light with λ > 870 nm is transmitted through the cells for collection by a thermal receiver. By combining electrical and thermal power collection, 75% of incident solar power is collected, far surpassing the collection capability of only photovoltaics. The module was tested on a dual-axis tracked parabolic concentrator dish at up to 160 suns for 60 cumulative on-sun hours while maintaining photovoltaic cell temperatures at an average of 50 °C via active cooling. The system performed as expected based on modeled values, and represents a cost-effective path forward for dual-generation of electricity and high-temperature heat with increased total efficiency. The capability is valuable in a wide range of commercial and industrial cogeneration applications.

14 SOLAR ENERGY↗

Repairing polycrystalline IN 100 using additive manufacturing (CRADA NFE-17-06791 Final Report)

The overall goal of this Manufacturing Demonstration Facility (MDF) technical collaboration project is to extend the use of the laser blown powder additive manufacturing process to enable the repair of polycrystalline high γ' Ni base super alloys, and to qualify the repaired parts for end use. The goal of phase 1 of this project was to evaluate the cracking susceptibility of Inconel 100 samples, and to identify parameters that would yield crack free repair deposits on representative geometries using a surrogate material as a substrate. A detailed design of experiments was performed in conjunction with thermomechanical modeling to determine processing conditions. A set of process parameters were identified which yielded minimal cracking. Further modeling was used to identify the preheat condition necessary to obtain crack free deposits. Following identification of the preheat, a furnace was integrated within the chamber of the blown powder Direct Energy Deposition (DED) system, and deposits were fabricated with on a preheated furnace. The results show that crack free deposits with dimensions 35x15x0.5 mm 3 can be fabricated. With this success obtained in phase 1 the goal of phase 2, if awarded, would be to fabricate the deposit on the actual IN 100 substrates develop heat treatment procedures and qualify the repair procedures.

36 MATERIALS SCIENCE↗

Transmissive microfluidic active cooling for concentrator photovoltaics

We present the design, fabrication, characterization, and field testing of transmissive active cooling for use in a point-focus spectrum-splitting hybrid concentrator photovoltaics/thermal (CPV/T) system. Seven parallel-path 100 μm thick microchannels are made using polydimethylsiloxane and attached to a CPV module containing a 6 × 6 array of 5.5 mm transmissive CPV cells on a sapphire substrate. Water is flowed through the microchannels to actively cool the CPV cells. The total transmittance of the CPV module reduces by 5.2% with the addition of the active cooling microchannels, relative to the module transmission with no microchannels. The peak cell temperature is measured as 69 °C with a thermal resistance of 9.35 K/W at 157 suns, well below the 110 °C maximum allowed temperature. A maximum flowrate of 16.7 g/s is achieved from a 13 psi pressure drop across the microchannels and manifold assembly. The flow characteristics within each microfluidic channel show maximum fluid velocity of 4.3 m/s (Re = 953) with a calculated convection coefficient of 1.7 × 10 4 W/m 2 K (Nu = 5.36). The CPV/T module and cooling system performance was validated during week-long outdoor tests under varying solar conditions up to 250 suns using a 2.7 m 2 parabolic dish collector mounted to a two-axis tracking system.

14 SOLAR ENERGY↗

Band engineering in transition metal dichalcogenides: Stacked versus lateral heterostructures

We calculate a large difference in the band alignments for transition metal dichalcogenide (TMD) heterojunctions when arranged in the stacked layer or lateral (in-plane) geometries, using direct supercell calculations. The stacked case follows the unpinned limit of the electron affinity rule, whereas the lateral geometry follows the strongly pinned limit of alignment of charge neutrality levels. TMDs therefore provide one of the few clear tests of band alignment models, whereas three-dimensional semiconductors give less stringent tests because of accidental chemical trends in their properties.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Ab-initio simulations of higher Miller index Si:SiO{sub 2} interfaces for fin field effect transistor and nanowire transistors

Models of three representative higher Miller index interfaces, Si(310):SiO{sub 2}, Si(410):SiO{sub 2}, and Si(331):SiO{sub 2}, have been built by an ab-initio molecular dynamics method. We show that each interface can be made as a fully bonded network without any defects and has a reasonable electronic structure for use in fin field effect transistors or gate-all-around nanowire devices. The differences in numbers of oxygen bridges are attributed to the intermediate sub-oxide components and the atomic step structure. The interface bonding schemes to passivate different densities of dangling bonds on different facets are also analyzed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Multifunctional oxides for integrated manufacturing of efficient graphene electrodes for organic electronics

Using multi-functional oxide films, we report on the development of an integration strategy for scalable manufacturing of graphene-based transparent conducting electrodes (TCEs) for organic electronics. A number of fundamental and process challenges exists for efficient graphene-based TCEs, in particular, environmentally and thermally stable doping, interfacial band engineering for efficient charge injection/extraction, effective wetting, and process compatibility including masking and patterning. Here, we show that all of these challenges can be effectively addressed at once by coating graphene with a thin (>10 nm) metal oxide (MoO{sub 3} or WO{sub 3}) layer. We demonstrate graphene electrode patterning without the need for conventional lithography and thereby achieve organic light emitting diodes with efficiencies exceeding those of standard indium tin oxide reference devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Materials selection for oxide-based resistive random access memories

The energies of atomic processes in resistive random access memories (RRAMs) are calculated for four typical oxides, HfO{sub 2}, TiO{sub 2}, Ta{sub 2}O{sub 5}, and Al{sub 2}O{sub 3}, to define a materials selection process. O vacancies have the lowest defect formation energy in the O-poor limit and dominate the processes. A band diagram defines the operating Fermi energy and O chemical potential range. It is shown how the scavenger metal can be used to vary the O vacancy formation energy, via controlling the O chemical potential, and the mean Fermi energy. The high endurance of Ta{sub 2}O{sub 5} RRAM is related to its more stable amorphous phase and the adaptive lattice rearrangements of its O vacancy.

36 MATERIALS SCIENCE↗

Light induced instability mechanism in amorphous InGaZn oxide semiconductors

A model of the negative bias illumination stress instability in InGaZn oxide is presented, based on the photo-excitation of electrons from oxygen interstitials. The O interstitials are present to compensate hydrogen donors. The O interstitials are found to spontaneously form in O-rich conditions for Fermi energies at the conduction band edge, much more easily that in related oxides. The excited electrons give rise to a persistent photoconductivity due to an energy barrier to recombination. The formation energy of the O interstitials varies with their separation from the H donors, which leads to a voltage stress dependence on the compensation.

36 MATERIALS SCIENCE↗

Carbon nanotube forests growth using catalysts from atomic layer deposition

We have grown carbon nanotubes using Fe and Ni catalyst films deposited by atomic layer deposition. Both metals lead to catalytically active nanoparticles for growing vertically aligned nanotube forests or carbon fibres, depending on the growth conditions and whether the substrate is alumina or silica. The resulting nanotubes have narrow diameter and wall number distributions that are as narrow as those grown from sputtered catalysts. The state of the catalyst is studied by in-situ and ex-situ X-ray photoemission spectroscopy. We demonstrate multi-directional nanotube growth on a porous alumina foam coated with Fe prepared by atomic layer deposition. This deposition technique can be useful for nanotube applications in microelectronics, filter technology, and energy storage.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Oxygen vacancy defects in Ta{sub 2}O{sub 5} showing long-range atomic re-arrangements

The structure, formation energy, and energy levels of the various oxygen vacancies in Ta{sub 2}O{sub 5} have been calculated using the λ phase model. The intra-layer vacancies give rise to unusual, long-range bonding rearrangements, which are different for each defect charge state. The 2-fold coordinated intra-layer vacancy is the lowest cost vacancy and forms a deep level 1.5 eV below the conduction band edge. The 3-fold intra-layer vacancy and the 2-fold inter-layer vacancy are higher cost defects, and form shallower levels. The unusual bonding rearrangements lead to low oxygen migration barriers, which are useful for resistive random access memory applications.

36 MATERIALS SCIENCE↗

Calculation of metallic and insulating phases of V{sub 2}O{sub 3} by hybrid density functionals

The electronic structure of vanadium sesquioxide V{sub 2}O{sub 3} in its different phases has been calculated using the screened exchange hybrid density functional. The hybrid functional accurately reproduces the experimental electronic properties of all three phases, the paramagnetic metal (PM) phase, the anti-ferromagnetic insulating phase, and the Cr-doped paramagnetic insulating (PI) phase. We find that a fully relaxed supercell model of the Cr-doped PI phase based on the corundum structure has a monoclinic-like local strain around the substitutional Cr atoms. This is found to drive the PI-PM transition, consistent with a Peierls-Mott transition. The PI phase has a calculated band gap of 0.15 eV, in good agreement with experiment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Diameter and wall number control of carbon nanotubes by chemical vapor deposition

We analyze the relationship between the average wall number (N) and the diameter (d) for carbon nanotubes (CNTs) grown by chemical vapour deposition. It is found that N depends linearly on d for diameters in the range of 2.5–10 nm, while single wall nanotubes predominate for diameters under about 2.1 nm. The linear relationship is found to depend somewhat on the growth conditions. It is also verified that the mean diameter depends on the diameter of the originating catalyst nanoparticle, and thus on the initial catalyst thickness where a thin film catalyst is used. This simplifies the characterisation of CNTs by electron microscopy. We also find a linear relationship between nanotube diameter and initial catalyst film thickness.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Low temperature growth of ultra-high mass density carbon nanotube forests on conductive supports

We grow ultra-high mass density carbon nanotube forests at 450 °C on Ti-coated Cu supports using Co-Mo co-catalyst. X-ray photoelectron spectroscopy shows Mo strongly interacts with Ti and Co, suppressing both aggregation and lifting off of Co particles and, thus, promoting the root growth mechanism. The forests average a height of 0.38 μm and a mass density of 1.6 g cm{sup −3}. This mass density is the highest reported so far, even at higher temperatures or on insulators. The forests and Cu supports show ohmic conductivity (lowest resistance ∼22 kΩ), suggesting Co-Mo is useful for applications requiring forest growth on conductors.

77 NANOSCIENCE AND NANOTECHNOLOGY↗