Engineering topics

Robinson, J. C.

Publications and source records attributed to Robinson, J. C..

At least 19 records

DOE OSTI2014

The Search for Electromagnetic Alteration of 235m U Decay

Electromagnetic modification of the 235m U isomer has been tested by placing the decaying system in a number of different environments. The isomer decays by internal conversion, which involves the electromagnetic transfer of energy from the nucleus to an atomic electron, and it is expected that this process can be altered by changing the photon density of states available to the nucleus. The two approaches pursued during this work included direct detection of the electron produced by the isomer decay using a micro-channel plate detector, and detection of the scintillation light produced when the electron interacted with various scintillators. With direct electron detection, variations in the isomer population were observed before and after covering the isomer, but this effect is attributed to systematic errors associated with the implantation and covering process. With the scintillator approach, scintillation light from the decay of the isomer was measured for the first time, and the decay half-life was directly identified while the isomer was embedded in a bulk material. No modification was observed, which leads to the conclusion that internal conversion of 235m U does not depend on the index of refraction of the surrounding environment in the way that spontaneous photon emission of an atomic system does. This result excludes many of the interesting applications of electromagnetic alteration of nuclear decay.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

NASA NTRS1991

Chemical vapor deposition coatings for oxidation protection of titanium alloys

Results of an experimental investigation of the oxidation protection afforded to Ti-14Al-21Nb and Ti-14Al-23Nb-2V titanium aluminides and Ti-17Mo-3Al-3Nb titanium alloy by aluminum-boron-silicon and boron-silicon coatings are presented. These coatings are applied by a combination of physical vapor deposition (PVD) and chemical vapor deposition (CVD) processes. The former is for the application of aluminum, and the latter is for codeposition of boron and silicon. Coating thickness is in the range of 2 to 7 microns, and coating weights are 0.6 to 2.0 mg/sq cm. Oxidation testing was performed in air at temperatures to 1255 K in both static and hypersonic flow environments. The degree of oxidation protection provided by the coatings is determined from weight change measurements made during the testing and post test compositional analyses. Temperature-dependent total normal emittance data are also presented for four coating/substrate combinations. Both types of coatings provided excellent oxidation protection for the exposure conditions of this investigation. Total normal emittances were greater than 0.80 in all cases.

Cunnington, G. R.↗

NASA NTRS1990

Non-catalytic coatings for hypersonic vehicle applications

CVD coatings of boron-oxygen-silicon and aluminum-boron-oxygen and silicon compositions were applied to alpha 2 and gamma titanium-aluminide alloys, and tested under simulated earth reentry conditions to evaluate oxidation protection, recombination effifiency and total emittance under cyclic exposures between temperatures of 300 and 1255 K. The degree of oxidation protection afforded to the alloys was evaluated from the amount of specimen weight gain after a 100 hour exposure to air at atmospheric pressure and at a temperature of 1255 K. Data are presented for two types of coatings, a monolithic and a multilayer, which have recombination efficiencies from 0.005 to 0.020 after ten one-half hour long simulated reentry cycles. Total normal emittance was 0.80 or greater and weight gain was less than 10 g/sq m both coating types. Compositional and morphological changes resulting from the exposures are discussed in relation to time-dependent variations in recombination efficiency.

Cunnington, G. R.↗

NASA NTRS1985

Vapor deposited emittance/catalysis coatings for superalloys in heatshield applications

Statically oxidized Inconel 617 and MA 956 superalloys were prepared with vapor deposited aluminosilicate layers and exposed to temperatures which simulated reentry conditions. The aluminosilicate layers were 1-2 microns thick. The trials consisted of exposures to 1500-2300 F heat while surface temperatures were monitored with pyrometers. Analyses were then performed of the catalytic activity, oxidation phenomena, and radiative properties after thermal cycling the specimens for 8 hr. Both alloys were found to be catalytic to the recombination processes of dissociated species in the reentry environment. The coatings reduced the catalytic activity by 40 percent for both alloys but did not change the emittance. An enhanced Cr depletion zone was detected in the Inconel samples, implying that the coating did not prevent diffusion loss of Cr. The coated MA 956, on the other hand, gained weight over the course of the trials.

Clark, R. K.↗

NASA NTRS1983

Application of a systematic finite-element model modification technique to dynamic analysis of structures

For abstract see A82-30178.

Robinson, J. C.↗

NASA NTRS1982

Studies of implicit and explicit solution techniques in transient thermal analysis of structures

Studies aimed at an increase in the efficiency of calculating transient temperature fields in complex aerospace vehicle structures are reported. The advantages and disadvantages of explicit and implicit algorithms are discussed and a promising set of implicit algorithms with variable time steps, known as GEARIB, is described. Test problems, used for evaluating and comparing various algorithms, are discussed and finite element models of the configurations are described. These problems include a coarse model of the Space Shuttle wing, an insulated frame tst article, a metallic panel for a thermal protection system, and detailed models of sections of the Space Shuttle wing. Results generally indicate a preference for implicit over explicit algorithms for transient structural heat transfer problems when the governing equations are stiff (typical of many practical problems such as insulated metal structures). The effects on algorithm performance of different models of an insulated cylinder are demonstrated. The stiffness of the problem is highly sensitive to modeling details and careful modeling can reduce the stiffness of the equations to the extent that explicit methods may become the best choice. Preliminary applications of a mixed implicit-explicit algorithm and operator splitting techniques for speeding up the solution of the algebraic equations are also described.

Adelman, H. M.↗

NASA NTRS1982

The SPAR thermal analyzer: Present and future

The SPAR thermal analyzer, a system of finite-element processors for performing steady-state and transient thermal analyses, is described. The processors communicate with each other through the SPAR random access data base. As each processor is executed, all pertinent source data is extracted from the data base and results are stored in the data base. Steady state temperature distributions are determined by a direct solution method for linear problems and a modified Newton-Raphson method for nonlinear problems. An explicit and several implicit methods are available for the solution of transient heat transfer problems. Finite element plotting capability is available for model checkout and verification.

Marlowe, M. B.↗

NASA NTRS1982

Some aspects of algorithm performance and modeling in transient thermal analysis of structures

The status of an effort to increase the efficiency of calculating transient temperature fields in complex aerospace vehicle structures is described. The advantages and disadvantages of explicit and implicit algorithms are discussed. A promising set of implicit algorithms with variable time steps, known as the GEAR package is described. Four test problems, used for evaluating and comparing various algorithms, were selected and finite element models of the configurations are described. These problems include a space shuttle frame component, an insulated cylinder, a metallic panel for a thermal protection system, and a model of the space shuttle orbiter wing. Results generally indicate a preference for implicit oer explicit algorithms for solution of transient structural heat transfer problems when the governing equations are stiff.

Adelman, H. M.↗

NASA NTRS1982

Evaluation of the SPAR thermal analyzer on the CYBER-203 computer

The use of the CYBER 203 vector computer for thermal analysis is investigated. Strengths of the CYBER 203 include the ability to perform, in vector mode using a 64 bit word, 50 million floating point operations per second (MFLOPS) for addition and subtraction, 25 MFLOPS for multiplication and 12.5 MFLOPS for division. The speed of scalar operation is comparable to that of a CDC 7600 and is some 2 to 3 times faster than Langley's CYBER 175s. The CYBER 203 has 1,048,576 64-bit words of real memory with an 80 nanosecond (nsec) access time. Memory is bit addressable and provides single error correction, double error detection (SECDED) capability. The virtual memory capability handles data in either 512 or 65,536 word pages. The machine has 256 registers with a 40 nsec access time. The weaknesses of the CYBER 203 include the amount of vector operation overhead and some data storage limitations. In vector operations there is a considerable amount of time before a single result is produced so that vector calculation speed is slower than scalar operation for short vectors.

Robinson, J. C.↗

NASA NTRS1982

Structural modeling of high Reynolds number wind tunnel models

A solid uninstrumented wing and a pressure instrumented wing having a tongue and groove type joint have been structurally modeled by using SPAR Structural Analysis System. The solid wing model can be analyzed by SPAR, using either solid elements or plate elements with reasonable accuracy. The instrumented wing models with tongue and groove joint can be modeled by using solid elements. A solid model representation for the wing with tongue and groove joint can be used for the cases where an error of 6 percent in deflections is acceptable.

Mehrotra, S. C.↗

NASA NTRS1982

Application of a systematic finite-element model modification technique to dynamic analysis of structures

A systematic finite-element model modification technique has been applied to two small problems and a model of the main wing box of a research drone aircraft. The procedure determines the sensitivity of the eigenvalues and eigenvector components to specific structural changes, calculates the required changes and modifies the finite-element model. Good results were obtained where large stiffness modifications were required to satisfy large eigenvalue changes. Sensitivity matrix conditioning problems required the development of techniques to insure existence of a solution and accelerate its convergence. A method is proposed to assist the analyst in selecting stiffness parameters for modification.

Robinson, J. C.↗

NASA NTRS1981

Some aspects of algorithm performance and modeling in transient thermal analysis of structures

The status of an effort to increase the efficiency of calculating transient temperature fields in complex aerospace vehicle structures is described. The advantages and disadvantages of explicit and implicit algorithms are discussed. A promising set of implicit algorithms with variable time steps, known as the GEAR package is described. Four test problems, used for evaluating and comparing various algorithms, have been selected and finite-element models of the configurations are described. These problems include a Space Shuttle frame component, an insulated cylinder, a metallic panel for a thermal protection system, and a model of the Space Shuttle Orbiter wing. Results generally indicate a preference for implicit over explicit algorithms for solution of transient structural heat transfer problems when the governing equations are 'stiff' (typical of many practical problems such as insulated metal structures).

Adelman, H. M.↗

NASA NTRS1981

Some aspects of algorithm performance and modeling in transient analysis of structures

The status of an effort to increase the efficiency of calculating transient temperature fields in complex aerospace vehicle structures is described. The advantages and disadvantages of explicit algorithms with variable time steps, known as the GEAR package, is described. Four test problems, used for evaluating and comparing various algorithms, were selected and finite-element models of the configurations are described. These problems include a space shuttle frame component, an insulated cylinder, a metallic panel for a thermal protection system, and a model of the wing of the space shuttle orbiter. Results generally indicate a preference for implicit over explicit algorithms for solution of transient structural heat transfer problems when the governing equations are stiff (typical of many practical problems such as insulated metal structures).

Adelman, H. M.↗

NASA NTRS1980

Analysis and design of a ceramic nozzle insert for the Langley 8-foot high temperature structures tunnel

An analysis is presented of various ceramic design concepts intended to improve nozzle throat life and tunnel performance in the hypersonic Langley 8-Foot High-Temperature Structures Tunnel, which uses methane-air combustion products as the wind-tunnel test medium. Calculations of the axial pressure distribution and heating rates in the air-cooled nozzle throat are presented, and desirable characteristics of a ceramic material to be used in the nozzle throat are outlined, including high-temperature strength, thermal shock and erosion resistance, low conductivity and low thermal expansion. Ceramic nozzle throat design concepts are then examined, with attention given to monolithic and layered constructions of cast ceramics, reaction-bonded materials and a fiber-reinforced silica-silica ceramic. Results of a finite element analysis of the temperatures and stresses characteristic of the various concepts are then presented which indicate the monolithic silica-silica and the layered silica-silica/reaction bonded silicon nitride concepts to be the most promising of those investigated.

Robinson, J. C.↗

NASA NTRS1979

Analysis methods and preliminary design study

The shuttle orbiter body flap was studied to define loads and temperatures and to assess various structural concepts. Laminated-structure analysis capability was required. An appraisal of the available structural analysis programs, NASTRAN and SPAR, indicates that neither had all the capabilities required. The thermal analysis program, MITAS solved the problem once a model was generated but model generation and verification was laborious and transfer of temperatures to the structural program usually required interpolation. Therefore it was decided to incorporate both capabilities in the SPAR finite element program.

Blackburn, C. L.↗

NASA NTRS1979

Simplified and refined finite element approaches for determining stresses and internal forces in geometrically nonlinear structural analysis

Two methods for determining stresses and internal forces in geometrically nonlinear structural analysis are presented. The simplified approach uses the mid-deformed structural position to evaluate strains when rigid body rotation is present. The important feature of this approach is that it can easily be used with a general-purpose finite-element computer program. The refined approach uses element intrinsic or corotational coordinates and a geometric transformation to determine element strains from joint displacements. Results are presented which demonstrate the capabilities of these potentially useful approaches for geometrically nonlinear structural analysis.

Robinson, J. C.↗

NASA NTRS1978

Evaluation of a hybrid, anisotropic, multilayered, quadrilateral finite element

A multilayered finite element with bending-extensional coupling is evaluated for: (1) buckling of general laminated plates; (2) thermal stresses of laminated plates cured at elevated temperatures; (3) displacements of a bimetallic beam; and (4) displacement and stresses of a single-cell box beam with warped cover panels. Also, displacements and stresses for flat and spherical orthotropic and anisotropic segments are compared with results from higher order plate and shell finite-element analyses.

Robinson, J. C.↗

NASA NTRS1978

Recent advances in thermal-structural analysis and design

A continuing effort to develop a comprehensive capability for thermal-structural analysis and automated design (sizing) is reviewed. A principal role in the activity is played by the finite element program SPAR which contains both an efficient structural and thermal analysis capability. The benefit of having thermal and structural analyses in the same finite element program is illustrated by the application of SPAR to design calculations for the National Transonic Facility - a cryogenic wind tunnel under construction at Langley. Some experience with large-scale thermal structural analysis problems, particularly the space shuttle orbiter, has led to the identification of some analysis needs. Those needs include automated model generation and data output for lumped parameter thermal analysis, faster solution methods for nonlinear transient heat transfer, automated interpolation of temperature data from a thermal finite element model to a dissimilar structural finite model, and automated techniques to identify the times at which the critical combinations of transient heating and loads occur on a structure.

Adelman, H. M.↗