Search NASA⌕ Search

Engineering topics

Rodriguez, J.

Publications and source records attributed to Rodriguez, J..

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Explosive fragmentation of additively manufactured stainless steel

Properties of fragmentation from an explosively driven 316L stainless steel spherical shell section fabricated by a laser powder bed additive manufacturing process with minimal surface finishing are investigated. This shell is driven by an insensitive high explosive, resulting in high strain rate deformation (>8 × 10 3 s –1 ) and failure of the stainless steel. Photonic Doppler velocimetry measures the expansion rate; dynamic radiography and high-speed imaging capture the fracture behavior of the stainless steel. The fracture response of the additively manufactured stainless steel shell is compared to published experimental results on additively manufactured 316L stainless steel and conventionally manufactured wrought 316L and 304 stainless steel shell fragmentation. Despite preferred crack orientation, suggesting the influence of surface grooves on fracture time, fragment size is identical to that measured in a similar experiment on wrought 304 stainless steel. Further analysis indicates that the 316L additively manufactured stainless steel shell exhibits comparable spall strength and fragmentation toughness to conventionally manufactured stainless steel yet lower failure strain due to surface stress concentrations.

36 MATERIALS SCIENCE↗
DOE OSTI2020

SuperCam Calibration Targets: Design and Development

Abstract SuperCam is a highly integrated remote-sensing instrumental suite for NASA’s Mars 2020 mission. It consists of a co-aligned combination of Laser-Induced Breakdown Spectroscopy (LIBS), Time-Resolved Raman and Luminescence (TRR/L), Visible and Infrared Spectroscopy (VISIR), together with sound recording (MIC) and high-magnification imaging techniques (RMI). They provide information on the mineralogy, geochemistry and mineral context around the Perseverance Rover. The calibration of this complex suite is a major challenge. Not only does each technique require its own standards or references, their combination also introduces new requirements to obtain optimal scientific output. Elemental composition, molecular vibrational features, fluorescence, morphology and texture provide a full picture of the sample with spectral information that needs to be co-aligned, correlated, and individually calibrated. The resulting hardware includes different kinds of targets, each one covering different needs of the instrument. Standards for imaging calibration, geological samples for mineral identification and chemometric calculations or spectral references to calibrate and evaluate the health of the instrument, are all included in the SuperCam Calibration Target (SCCT). The system also includes a specifically designed assembly in which the samples are mounted. This hardware allows the targets to survive the harsh environmental conditions of the launch, cruise, landing and operation on Mars during the whole mission. Here we summarize the design, development, integration, verification and functional testing of the SCCT. This work includes some key results obtained to verify the scientific outcome of the SuperCam system.

Manrique, J. A. (ORCID:0000000220532819)↗
NASA NTRS2019

Thermal design and on-orbit performance of the ECOSTRESS instrument

The ECOSystem Spaceborne Thermal Radiometer Experiment on Space Station (ECOSTRESS) instrument, launched on June 29, 2018, has completed nine months of operation in space. ECOSTRESS is a multispectral thermal infrared imaging radiometer and its primary mission is to investigate and understand how climate change affects water and carbon usage on Earth. The thermal control subsystem consists of a combination of active and passive components to maintain instrument components within the allowable flight temperature limits. Its focal plane detector is cooled to 65K by a pair of mechanical cryocoolers and a third mechanical cryocooler cools an intermediate cold shield to 130K. The heat dissipation generated by cryocoolers and electronics, is removed through non-planar cold plates and tube-on plate heat exchanger, which are cooled by a circulating fluid -EF module. The heat collected by the JEM-EF fluid is exchanged with a fluid loop that circulates through radiators located on the exterior of the Space Station. This paper provides an overview of the thermal and cryogenic system design, thermal analysis results and reviews the on-orbit thermal performance.

Romero, M.↗
NASA NTRS2018

New Capabilities, Products and Usage of NASA Earth Imagery for Near Real Time Applications

NASA's Worldview and Global Imagery Browse Services (GIBS) have provided near real time (NRT) imagery to the public since 2011 and continue to add new capabilities and products. As a web map app for GIBS, Worldview (https://worldview.earthdata.nasa.gov) has recently added new features to support NRT applications such as a "before" and "after" comparison capability and support for geostationary imagery. As an open set of standards-based web map services, GIBS (https://earthdata.nasa.gov/gibs) has added several new NRT imagery products and will soon add new capabilities for better integration with Geographic Information System (GIS) clients. One of NASA's original NRT imagery systems and a long-running workhorse, Rapid Response, has been retired and replaced with a modern, mobile-friendly, and low-bandwidth app dubbed Worldview Snapshots (https://wvs.earthdata.nasa.gov). Finally, this presentation will demonstrate recent usage of these tools and services by those in the NRT community.

Boller, R.↗
DOE OSTI2018

Meta-equilibrium transition microstructure for maximum austenite stability and minimum hardness in a Ti-stabilized supermartensitic stainless steel

We report that the maximization of stable reverted austenite at room temperature through inter-critical tempering is a widely used method to reduce hardness in supermartensitic stainless steels. Nevertheless, partial martensitic transformation might occur due to insufficient compositional stabilization. In this work, we conducted a time-resolved triple-step inter-critical tempering, specially designed to obtain maximum austenite stability and minimum hardness through the progressive suppression of the martensitic transformation. The mechanism behind the progressive increase in stable reverted austenite was the generation of a meta-equilibrium state, which imposed a limit in both high temperature austenite reversion and room temperature austenite stabilization. Such limit corresponded to the high temperature volume fraction of austenite, obtained right before cooling from the first cycle. Additionally, this effect was associated to the Ni-rich fresh martensite laths acting as local Ni compositional pockets, providing site-specific austenite reversion; and to the suppression of any additional nucleation at the Ni-poor matrix as the T0 temperature for austenite reversion was strongly increased. The softening mechanism was mainly controlled by the carbon arrest effect by the precipitation of Ti (C, N), which was completed after the first tempering cycle. Nevertheless, maximizing reverted austenite and suppressing fresh martensite at room temperature did not result in additional hardness reductions.

36 MATERIALS SCIENCE↗
NASA NTRS2017

Exposing NASA's Earth Observations to the Applications Community and Public

NASA's Earth Observing System (EOS) generates a wealth of data products which are generally intended for scientific research. In recent years, however, this data has also become more accessible to the applications community and public through the Worldview app and Global Imagery Browse Services (GIBS). These mapping interfaces provide historical and near real time access to NASA's Earth observations for a wide range of uses. This presentation will focus on how the applications community, public, and media use these interfaces for decision-making, leisure, and anything in between.

web mappin↗
DOE OSTI2017

Compositional analysis on the reverted austenite and tempered martensite in a Ti-stabilized supermartensitic stainless steel: Segregation, partitioning and carbide precipitation

We present that controlling the amount of reverted austenite at room temperature allows for tailoring of mechanical properties in supermartensitic stainless steels. The austenite reversion and stabilization occurs during inter-critical tempering through partitioning of austenite-stabilizing elements. The degree of partitioning greatly depends on the reversion temperature, which dictates the local equilibrium conditions. Atom probe tomography and energy dispersive spectroscopy in transmission electron microscopy were used to study the austenite reversion mechanism in terms of the elemental distribution of austenite-stabilizing, ferrite-stabilizing and carbide forming elements. Synchrotron X-ray diffraction confirmed that the austenite equilibrium phase fraction was reached after 2.5 h of isothermal reversion at 625 °C, allowing for direct comparison with thermodynamic and kinetic calculations. However, such soaking time was not enough to produce compositional homogenization in the reverted austenite. The austenite reversion and stabilization mechanism was related mainly to strong partitioning of Ni. Negligible partitioning of Cr, Mo, Si and Ti were observed. Instead, these elements were strongly segregated at the reverted austenite/martensite interfaces. Carbon and Ti played a secondary role in the austenite stabilization through the precipitation of nano-sized Ti (C,N) with partial substitution of Ti by Mo. Finally, virtually carbon-free austenite and martensite were observed away from the interfaces and precipitates.

36 MATERIALS SCIENCE↗
NASA NTRS2017

Single-dish and VLBI Observations of Cygnus X-3 During the 2016 Giant Flare Episode

In 2016 September, the microquasar Cygnus X-3 underwent a giant radio flare, which was monitored for 6 d with the Medicina Radio Astronomical Station and the Sardinia Radio Telescope. Long observations were performed in order to follow the evolution of the flare on an hourly scale, covering six frequency ranges from 1.5 to 25.6 GHz. The radio emission reached a maximum of 13.2 +/- 0.7 Jy at 7.2 GHz and 10 +/- 1 Jy at 18.6 GHz. Rapid flux variations were observed at high radio frequencies at the peak of the flare, together with rapid evolution of the spectral index: α steepened from 0.3 to 0.6 (with Sν ∝ ν −α) within 5 h. This is the first time that such fast variations are observed, giving support to the evolution from optically thick to optically thin plasmons in expansion moving outward from the core. Based on the Italian network (Noto, Medicina and SRT) and extended to the European antennas (Torun, Yebes, Onsala), very long baseline interferometry (VLBI) observations were triggered at 22 GHz on five different occasions, four times prior to the giant flare, and once during its decay phase. Flux variations of 2 h duration were recorded during the first session. They correspond to a mini-flare that occurred close to the core 10 d before the onset of the giant flare. From the latest VLBI observation we infer that 4 d after the flare peak the jet emission was extended over 30 mas.

Egron, E.↗
NASA NTRS2016

Web Map Apps using NASA's Earth Observing Fleet

Through the miracle of open web mapping services for satellite imagery, a garden of new applications has sprouted to monitor the planet across a variety of domains. The Global Imagery Browse Services (GIBS) provide free and open access to full resolution imagery captured by NASAs Earth observing fleet. Spanning 15+ years and running through as recently as a few hours ago, GIBS aims to provide a general-purpose window into NASA's vast archive of the planet. While the vast nature of this archive can be daunting, many domain-specific applications have been built to meet the needs of their respective communities. This presentation will demonstrate a diverse set of these new applications which can take planetarium visitors into (virtual) orbit, guide fire resource managers to hotspots, help anglers find their next catch, illustrate global air quality patterns to local regulators, and even spur a friendly competition to find clouds which are shaped the most like cats. We hope this garden will continue to grow and will illustrate upcoming upgrades to GIBS which may open new pathways for development. data visualization, web services, open access

data visualization↗
DOE OSTI2016

GRS 1739-278 observed at very low luminosity with XMM-Newton and NuSTAR

We present a detailed spectral analysis of XMM-Newton and NuSTAR observations of the accreting transient black hole GRS 1739−278 during a very faint low hard state at ∼0.02% of the Eddington luminosity (for a distance of 8.5 kpc and a mass of 10 M{sub ⊙}). The broadband X-ray spectrum between 0.5 and 60 keV can be well-described by a power-law continuum with an exponential cutoff. The continuum is unusually hard for such a low luminosity, with a photon index of Γ = 1.39 ± 0.04. We find evidence for an additional reflection component from an optically thick accretion disk at the 98% likelihood level. The reflection fraction is low, with R{sub refl}=0.043{sub −0.023}{sup +0.033}. In combination with measurements of the spin and inclination parameters made with NuSTAR during a brighter hard state by Miller et al., we seek to constrain the accretion disk geometry. Depending on the assumed emissivity profile of the accretion disk, we find a truncation radius of 15–35 R{sub g} (5–12 R{sub ISCO}) at the 90% confidence limit. These values depend strongly on the assumptions and we discuss possible systematic uncertainties.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS2016

GRS 1739-278 Observed at Very Low Luminosity with XMM-Newton and NuSTAR

We present a detailed spectral analysis of XMM-Newton and NuSTAR observations of the accreting transient black hole GRS1739−278 during a very faint low hard state at ∼0.02% of the Eddington luminosity (for a distance of 8.5 kpc and a mass of 10 solar mass). The broadband X-ray spectrum between 0.5 and 60 keV can be well-described by a power-law continuum with an exponential cutoff. The continuum is unusually hard for such a low luminosity, with a photon index of Γ=1.39+/-0.04. We find evidence for an additional reflection component from an optically thick accretion disk at the 98% likelihood level. The reflection fraction is low, with R(sub refl) = 0.043(exp + 0.033)(sub - 0.023). In combination with measurements of the spin and inclination parameters made with NuSTAR during a brighter hard state by Miller et al., we seek to constrain the accretion disk geometry. Depending on the assumed emissivity profile of the accretion disk, we find a truncation radius of 15-35 R(sub g) (5-12 R(sub ISCO)) at the 90% confidence limit. These values depend strongly on the assumptions and we discuss possible systematic uncertainties.

Fürst, F.↗
DOE OSTI2016

High-energy gamma-ray observations of the accreting black hole V404 Cygni during its 2015 June outburst

In this paper, we report on Fermi/Large Area Telescope observations of the accreting black hole low-mass X-ray binary V404 Cygni during its outburst in 2015 June–July. Detailed analyses reveal a possible excess of γ-ray emission on 2015 26 June, with a very soft spectrum above 100 MeV, at a position consistent with the direction of V404 Cyg (within the 95 per cent confidence region and a chance probability of 4 × 10 -4 ). This emission cannot be associated with any previously known Fermi source. Its temporal coincidence with the brightest radio and hard X-ray flare in the light curve of V404 Cyg, at the end of the main active phase of its outburst, strengthens the association with V404 Cyg. If the γ-ray emission is associated with V404 Cyg, the simultaneous detection of 511 keV annihilation emission by INTEGRAL reqires that the high-energy γ-rays originate away from the corona, possibly in a Blandford–Znajek jet. Finally, the data give support to models involving a magnetically arrested disc where a bright γ-ray jet can re-form after the occurrence of a major transient ejection seen in the radio.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2016

Determination of the mechanical properties of blisters by nanoindentation

In light-water reactors, a zirconium oxide layer will be formed at the outer surface of the fuel cladding as a consequence of the chemical reaction which takes place between zirconium and the cooling water. This zirconium oxide layer is a good thermal insulator, but at some point, it may spall-out. As a consequence, a cold spot will be formed at the outer surface of the cladding. In this situation, the hydrogen will quickly migrate to this spot to form a highly-enriched hydride zone, known as blister. In this work, an experimental procedure has been devised to produce blisters with a similar shape to the ones reported in the literature for irradiated cladding with severe hydriding. Nano-indentation tests were performed on blisters prepared in laboratory. A numerical simulation by the finite element method was developed to fit the load versus penetration depth data from the aforementioned nano-indentation tests. By means of an inverse process which combines experimental data and numerical simulations, the constitutive equation of the blister was determined. The process has been used to calculate the plastic stress-strain curve of the blister under study at room temperature. The results show an almost perfect numerical fitting of the experimental data.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗