Search NASA⌕ Search

Engineering topics

Rodriguez, Mark A.

Publications and source records attributed to Rodriguez, Mark A..

At least 19 records

Characterization of MoS 2 films via simultaneous grazing incidence X-ray diffraction and grazing incidence X-ray fluorescence (GIXRD/GIXRF)

Physical vapor deposited (PVD) molybdenum disulfide (nominal composition MoS 2 ) is employed as a thin film solid lubricant for extreme environments where liquid lubricants are not viable. The tribological properties of MoS 2 are highly dependent on morphological attributes such as film thickness, orientation, crystallinity, film density, and stoichiometry. These structural characteristics are controlled by tuning the PVD process parameters, yet undesirable alterations in the structure often occur due to process variations between deposition runs. Nondestructive film diagnostics can enable improved yield and serve as a means of tuning a deposition process, thus enabling quality control and materials exploration. Grazing incidence X-ray diffraction (GIXRD) for MoS 2 film characterization provides valuable information about film density and grain orientation (texture). However, the determination of film stoichiometry can only be indirectly inferred via GIXRD. The combination of density and microstructure via GIXRD with chemical composition via grazing incidence X-ray fluorescence (GIXRF) enables the isolation and decoupling of film density, composition, and microstructure and their ultimate impact on film layer thickness, thereby improving coating thickness predictions via X-ray fluorescence. We have augmented an existing GIXRD instrument with an additional X-ray detector for the simultaneous measurement of energy-dispersive X-ray fluorescence spectra during the GIXRD analysis. This combined GIXRD/GIXRF analysis has proven synergetic for correlating chemical composition to the structural aspects of MoS 2 films provided by GIXRD. We present the usefulness of the combined diagnostic technique via exemplar MoS 2 film samples and provide a discussion regarding data extraction techniques of grazing angle series measurements.

MoS2↗

Refining Microstructures in Additively Manufactured Al/Cu Gradients Through TiB 2 Inclusions

Here, the additive manufacture of compositionally graded Al/Cu parts by laser engineered net shaping (LENS) is demonstrated. The use of a blue light build laser enabled deposition on a Cu substrate. The thermal gradient and rapid solidification inherent to selective laser melting enabled mass transport of Cu up to 4 mm from a Cu substrate through a pure Al deposition, providing a means of producing gradients with finer step sizes than the printed layer thicknesses. Divorcing gradient continuity from layer or particle size makes LENS a potentially enabling technology for the manufacture of graded density impactors for ramp compression experiments. Printing graded structures with pure Al, however, was prevented by the growth of Al 2 Cu 3 dendrites and acicular grains amid a matrix of Al 2 Cu. A combination of adding TiB 2 grain refining powder and actively varying print layer composition suppressed the dendritic growth mode and produced an equiaxed microstructure in a compositionally graded part. Material phase was characterized for crystal structure and nanoindentation hardness to enable a discussion of phase evolution in the rapidly solidifying melt pool of a LENS print.

36 MATERIALS SCIENCE↗

Tunable negative coefficient thermal expansion materials and composites

The present disclosure is directed to variable composition ceramics. Zr (2−x) Hf (x) WP 2 O 12 and Hf 2 WP 2 O 12 exhibit large negative thermal expansion that is linear over a large temperature range up to at least 900° C., These new ceramic material particles may be mixed with polymers to make a composite suitable for use in backsheets for photovoltaic modules or in other applications. The thermal expansion coefficient of the composite can be tailored to match that of the solar cell in order to reduce stress resulting from daily thermal cycling.

Gordon, Margaret Ellen↗

Fabrication and characterization of net-shaped iron nitride-amine-epoxy soft magnetic composites

Soft magnetic composites (SMCs) offer a promising alternative to electrical steels and soft ferrites in high performance motors and power electronics. They are ideal for incorporation into passive electronic components such as inductors and transformers, which require a non-permanent magnetic core to rapidly switch magnetization. As a result, there is a need for materials with the right combination of low coercivity, low magnetic remanence, high relative permeability, and high saturation magnetization to achieve these goals. Iron nitride is an attractive soft magnetic material for incorporation into an amine/epoxy resin matrix. This permits the synthesis of net-shaped SMCs using a “bottom-up” approach for overcoming the limitations of current state-of-the-art SMCs made via conventional powder metal processing techniques. In this work we present the fabrication of various net-shaped, iron nitride-based SMCs using two different amine/epoxy resin systems and their magnetic characterization. The maximum volume loading of iron nitride reached was ~77% via hot pressing, which produced SMCs with a saturation magnetic polarization (J s ) of ~0.9 T, roughly 2–3 times the J s of soft ferrites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electrical Shock During Phone Assisted Troubleshooting of Laboratory Equipment

We report researchers have the potential to be exposed to a wide variety of hazards inherent to the equipment they use and maintain. When equipment does not function as expected, researchers sometimes reach out to their vendors for assistance. Early diagnostic or troubleshooting interactions between researcher and vendor are often conducted over the telephone and can lead to researchers performing work outside of their area of expertise and exposure to unknown hazards. This type of interaction significantly contributed to an incident where during diagnostic activities a researcher accidentally contacted, and discharged, a capacitor in an X-ray diffraction instrument. While this incident did not produce a serious injury, if the capacitor discharge path had occurred hand-to-hand across the heart, a serious injury may have been possible.

47 OTHER INSTRUMENTATION↗

Li-ion and Na-ion intercalation in layered MnO 2 cathodes enabled by using bismuth as a cation pillar

Low-cost batteries based on Earth-abundant materials are needed for large-scale electrical storage for the grid. Cathodes based almost entirely on Mn oxides would reduce overall battery cost but cycling of Mn oxides is often not stable. In Li-ion cells, most polymorphs of MnO 2 undergo irreversible transformation to spinel LiMn 2 O 4 during cycling, causing capacity loss. Doping MnO 2 with Bi is known to stabilize the structure, but previous reports have relied on low-crystallinity material making it impossible to pinpoint the Bi location in the structure or its mechanism. In this work, we report a series of hydrated Bi-doped layered MnO 2 compounds and characterize their structures as a function of Bi amount. Bi is shown to reside in the material interlayer, provoking higher long-range structural order even at a low doping level of 1.3%. Doped material improves the specific capacity and stability of cycling in both Li-ion and Na-ion cells. A high level of Bi doping, 4.3%, causes loss of the interlayer crystal water in non-aqueous electrolyte, and this reduces the interlayer distance. Crystal water is shown to be beneficial in a Na-ion system, while its loss improves Li-ion cycling. This provides fundamental insight into how pillaring by a heavy, multivalent cation stabilizes layered oxides.

25 ENERGY STORAGE↗

Improved quantum yield in geometrically constrained tetraphenylethylene-based metal–organic frameworks

In this paper we report the synthesis of a novel, tetraphenylethylene-based ligand for metal–organic frameworks (MOFs). Incorporation of this ligand into a Zn- or Eu-based MOF increased the quantum yield (QY) by almost 2.5× compared to the linker alone. Furthermore, the choice of guest solvent impacted the QY and solvatochromatic response. These shifts are consistent with solvent dielectric constant as well as molecular polarizability.

36 MATERIALS SCIENCE↗

Uncovering microstructure and composition susceptibility of high permittivity ceramic granules to plasma-induced arc breakdown

Effective diversion of surge currents is vital to prevent unwanted damage to sensitive electronics. Among the most successful and efficient strategies relies on a dielectric stimulated arc breakdown mechanism with high permittivity ceramic granules in a spark-gap geometry. Although generally regarded as a self-healing process, substantial energy deposition may occur that, over time, diminishes the ability to withstand repeated electrical assaults. We investigate the susceptibility of lead–magnesium–niobate–lead titanate (PMN–PT) granule microstructure and composition changes following many exposures to high voltage impulses resulting in arc breakdown. Scanning electron microscopy and energy-dispersive spectroscopy mapping reveal a broad range of thermal and mechanical defects entailing thermal reduction of constituent PMN–PT metal ions and recasting due to rapid eruption of volatile species. Additionally, evidence of local melting and microcracking are apparent that can have deleterious impact on the proper function of the granules, namely, the ability to concentrate electric fields across air gaps to establish and sustain discharge pathways. We propose that the localized nature of damage and stochasticity associated with the dielectric stimulated breakdown mechanism may allow granules to maintain functionality provided no permanent conduction paths are established.

36 MATERIALS SCIENCE↗

Sodium electrochemical interfaces with NaSICON-type ceramics

The present invention is directed to the modification of sodium electrochemical interfaces to improve performance of NaSICON-type ceramics in a variety of electrochemical applications. Enhanced mating of the separator-sodium interface by means of engineered coatings or other surface modifications results in lower interfacial resistance and higher performance at increased current densities, enabling the effective operation of molten sodium batteries and other electrochemical technologies at low and high temperatures.

36 MATERIALS SCIENCE↗

Crystal structures of polymerized lithium chloride and dimethyl sulfoxide in the form of {2LiCl·3DMSO} n and {LiCl·DMSO} n

Two novel LiCl·DMSO polymer structures were created by combining dry LiCl salt with dimethyl sulfoxide (DMSO), namely, catena-poly[[chlorido­lithium(I)]-μ-(dimethyl sulfoxide)-κ 2 O:O-[chlorido­lithium(I)]-di-μ-(dimethyl sulfoxide)-κ 4 O:O], [Li 2 Cl 2 (C 2 H 6 OS) 3 ]n, and catena-poly[lithium(I)-μ-chlorido-μ-(dimethyl sulfoxide)-κ 2 O:O], [LiCl(C 2 H 6 OS)]n. The initial synthesized phase had very small block-shaped crystals (<0.08 mm) with monoclinic symmetry and a 2 LiCl: 3 DMSO ratio. As the solution evaporated, a second phase formed with a plate-shaped crystal morphology. After about 20 minutes, large (>0.20 mm) octa­hedron-shaped crystals formed. The plate crystals and the octa­hedron crystals are the same tetra­gonal structure with a 1 LiCl: 1 DMSO ratio. These structures are reported and compared to other known LiCl·solvent compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Trends in Siting of Metals in Heterometallic Nd–Yb Metal–Organic Frameworks and Molecular Crystals

Several studies suggest that metal ordering within metal–organic frameworks (MOFs) is important for understanding how MOFs behave in relevant applications; however, these siting trends can be difficult to determine experimentally. To garner insight into the energetic driving forces that may lead to nonrandom ordering within heterometallic MOFs, we employ density functional theory (DFT) calculations on several bimetallic metal–organic crystals composed of Nd and Yb metal atoms. We also investigate the metal siting trends for a newly synthesized MOF. Our DFT-based energy of mixing results suggest that Nd will likely occupy sites with greater access to electronegative atoms and that local homometallic domains within a mixed-metal Nd–Yb system are favored. We also explore the use of less computationally extensive methods such as classical force fields and cluster expansion models to understand their feasibility for large system sizes. Here, this study highlights the impact of metal ordering on the energetic stability of heterometallic MOFs and crystal structures.

energy of mixing↗

Processing and properties of PSZT 95/5 ceramics with varying Ti and Nb substitution

Niobium doped lead-tin-zirconate-titanate ceramics near the PZT 95/5 orthorhombic AFE – rhombohedral FE morphotropic phase boundary Pb 1-0.5y (Zr 0.865-x Ti x Sn 0.135 ) 1-y Nb y O 3 were prepared according to a 2 2+1 factorial design with x = 0.05, 0.07 and y = 0.0155, 0.0195. The ceramics were prepared by a traditional solid-state synthesis route and sintered to near full density at 1250°C for 6 hours. All compositions were ~98% dense with no detectable secondary phases by XRD. The ceramics exhibited equiaxed grains with intergranular porosity and grain size was ~5 μm, decreasing with niobium substitution. Compositions exhibited remnant polarization values of ~32 μC/cm 2 , increasing with Ti substitution. Depolarization by the hydrostatic pressure induced FE-AFE phase transition was drastically affected by variation of the Ti and Nb substitution, increasing at a rate of 113 MPa / 1% Ti and 21 MPa / 1% Nb. Total depolarization output was insensitive to the change in Ti and Nb substitution, ~32.8 μC/cm 2 for the PSZT ceramics. The R3c-R3m and R3m-Pm3m phase transition temperatures on heating ranged from 90 to 105°C and 183 to 191°C, respectively. Ti substitution stabilized the R3c and R3m phases to higher temperatures, while Nb substitution stabilized the Pm3m phase to lower temperatures. Thermal hysteresis of the phase transitions was also observed in the ceramics, with transition temperature on cooling being as much as 10°C lower.

36 MATERIALS SCIENCE↗

Processing, structure, and thermal properties of ZrW 2 O 8 , HfW 2 O 8 , HfMgW 3 O 12 , Al(HfMg) 0.5 W 3 O 12 , and Al 0.5 Sc 1.5 W 3 O 12 negative and zero thermal expansion coefficient ceramics

Negative and zero coefficient of thermal expansion (CTE) materials are of interest for developing polymer composites in electronic circuits that match the expansion of Si and in zero CTE supports for optical components, e.g., mirrors. In this work, the processing challenges and stability of ZrW 2 O 8 , HfW 2 O 8 , HfMgW 3 O 12 , Al(HfMg) 0.5 W 3 O 12 , and Al 0.5 Sc 1.5 W 3 O 12 negative and zero thermal expansion coefficient ceramics are discussed. Al 0.5 Sc 1.5 W 3 O 12 is demonstrated to be a relatively simple oxide to fabricate in large quantity and is shown to exhibit single phase up to 1300 °C in air and inert N 2 environments. The negative and zero CTE behavior was confirmed with dilatometry. Thermal conductivity and heat capacity were reported for the first time for HfMgW 3 O 12 and Al 0.5 Sc 1.5 W 3 O 12 and thermal conductivity was found to be very low (~0.5 W/mK). Grüneisen parameter is also estimated. Methods for integration of Al 0.5 Sc 1.5 W 3 O 12 with other materials was examined and embedding 50 vol% of the ceramic powder in flexible epoxy was demonstrated with a commercial vendor.

36 MATERIALS SCIENCE↗