Search NASA⌕ Search

Engineering topics

Rodriguez, Mark

Publications and source records attributed to Rodriguez, Mark.

36 records · Page 2

Photocatalytic Material Surfaces for SARS-CoV-2 Virus Inactivation

Severe acute respiratory syndrome coronavirus 2 (SARS-COV-2) can be spread through close contact or through fomite mediated transmission. This study details the fabrication and analysis of a photocatalyst surface which can rapidly inactivate SARS-COV-2 to limit spread of the virus by fomite mediated transmission. The surface being developed at Sandia for this purpose is a minimally hazardous Ag-Ti0 2 nanomaterial which is engineered to have high photocatalytic activity. Initial results at Sandia California in a BSL-2 safe surrogate virus- Vesicular Stomatitis Virus (VSV) show a significant difference between the photocatalyst material under exposure to visible light than controls. Additionally, UV-A light (365 nm) was found to eliminate SARS-COV-2 after 9 hours on all tested surfaces with irradiance of 15 mW/cm 2 equivalent to direct circumsolar irradiance.

59 BASIC BIOLOGICAL SCIENCES↗

Thickness dependence of Al 0.88 Sc 0.12 N thin films grown on silicon

The thickening behavior of aluminum scandium nitride (Al 0.88 Sc 0.12 N) films grown on Si(111) substrates has been investigated experimentally using X-ray diffraction (XRD), transmission electron microscopy (TEM), atomic force microscopy, and residual stress measurement. Al 0.88 Sc 0.12 N films were grown with thicknesses spanning 14 nm to 1.1 um. TEM analysis shows that the argon sputter etch used to remove the native oxide prior to deposition produced an amorphous, oxygen-rich surface, preventing epitaxial growth. XRD analysis of the films show that the A1ScN(002) orientation improves as the films thicken and the XRD A1ScN(002) rocking curve full width half maximum decreases to 1.34 q for the 1.1 pm thick film. XRD analysis shows that the unit cell is expanded in both the a- and c-axes by Sc doping; the a-axis lattice parameter was measured to be 3.172 ± 0.007 A and the c-axis lattice parameter was measured to be 5.000 ± 0.001 A, representing 1.96% and 0.44% expansions over aluminum nitride lattice parameters, respectively. The grain size and roughness increase as the film thickness increases. A stress gradient forms through the film; the residual stress grows more tensile as the film thickens, from -1.24 GPa to +8.5MPa.

36 MATERIALS SCIENCE↗

MOF-Sensitized Solar Cells Enabled by a Pillared Porphyrin Framework

Metal–organic frameworks (MOFs) are highly ordered, functionally tunable supramolecular materials with the potential to improve dye-sensitized solar cells (DSSCs). Several recent reports have indicated that photocurrent can be generated in Grätzel-type DSSC devices when MOFs are used as the sensitizer. However, the specific role(s) of the incorporated MOFs and the potential influence of residual MOF precursor species on device performance are unclear. Herein, we describe the assembly and characterization of a simplified DSSC platform in which isolated MOF crystals are used as the sensitizer in a planar device architecture. We selected a pillared porphyrin framework (PPF) as the MOF sensitizer, taking particular care to avoid contamination from light-absorbing MOF precursors. Photovoltaic and electrochemical characterization under simulated 1-sun and wavelength-selective illumination revealed photocurrent generation that is clearly ascribable to the PPF MOF. In conclusion, continued refinement of highly versatile MOF structure and chemistry holds promise for dramatic improvements in emerging photovoltaic technologies.

14 SOLAR ENERGY↗

In situ observation of ErD2 formation during D-2 loading via neutron diffraction

In an effort to better understand the structural changes occurring during hydrogen loading of erbium target materials, we have performed in situ D{sub 2} loading of erbium metal (powder) at temperature (450 C) with simultaneous neutron diffraction analysis. This experiment tracked the conversion of Er metal to the {alpha} erbium deuteride (solid-solution) phase and then into the {beta} (fluorite) phase. Complete conversion to ErD{sub 2.0} was accomplished at 10 Torr D{sub 2} pressure with deuterium fully occupying the tetrahedral sites in the fluorite lattice.

08 HYDROGEN↗