Engineering topics

Rodriguez, Pete

Publications and source records attributed to Rodriguez, Pete.

4 records

NASA NTRS2001

Analysis of Proposed Fully Internal Compression Geometry for an RBCC Engine

A proposed fully internal compression geometry for rocket based combined cycle (RBCC) engine, STEPER (Space Transportation Engine Prototype for Engineering Research), was investigated numerically in this paper. The Steper-engine has been designed to power a reusable launch vehicle that may take-off horizontally, accelerate to Mach 2, sustain supersonic air-breathing combustion to Mach 10 while ascending to 50 km and then transition to full rocket propulsion to enter low earth orbit. The proposed engine geometry replaces the alternative conical center-body and supporting struts with a quasi-stationary upper and lower compression ramps. A cluster of thruster nozzles was embedded inside the ramp and provide thrust to the engine with additional fuel existing at the nozzle exit. The proposed geometry eases the problem of cooling hard to reach cavities. This design geometry was investigated numerically. Both perfect gas and finite rate chemistry analysis were performed. Results indicated that the emanating oblique shock waves produced by the upper and lower compression ramps intersect and the reflecting shocks do not reach the wall of the combustor but rather downstream. This effect allows the formation of two distinct regions that can be considered the core region and the surrounding flow region. The core region has higher pressure and higher temperature than the surrounding region. Therefore providing some reduction to the thermal loads to the inner walls.

Rojas-Oviedo, Ruben↗

NASA NTRS2000

Airbreathing Propulsion System Analysis Using Multithreaded Parallel Processing

In this paper, parallel processing is used to analyze the mixing, and combustion behavior of hypersonic flow. Preliminary work for a sonic transverse hydrogen jet injected from a slot into a Mach 4 airstream in a two-dimensional duct combustor has been completed [Moon and Chung, 1996]. Our aim is to extend this work to three-dimensional domain using multithreaded domain decomposition parallel processing based on the flowfield-dependent variation theory. Numerical simulations of chemically reacting flows are difficult because of the strong interactions between the turbulent hydrodynamic and chemical processes. The algorithm must provide an accurate representation of the flowfield, since unphysical flowfield calculations will lead to the faulty loss or creation of species mass fraction, or even premature ignition, which in turn alters the flowfield information. Another difficulty arises from the disparity in time scales between the flowfield and chemical reactions, which may require the use of finite rate chemistry. The situations are more complex when there is a disparity in length scales involved in turbulence. In order to cope with these complicated physical phenomena, it is our plan to utilize the flowfield-dependent variation theory mentioned above, facilitated by large eddy simulation. Undoubtedly, the proposed computation requires the most sophisticated computational strategies. The multithreaded domain decomposition parallel processing will be necessary in order to reduce both computational time and storage. Without special treatments involved in computer engineering, our attempt to analyze the airbreathing combustion appears to be difficult, if not impossible.

Schunk, Richard Gregory↗

NASA NTRS2000

Microgravity Disturbance Characterization of the Quench Module Insert (QMI) Phase Change Device (PCD)

The Materials Science Research Facility (MSRF) is a multi-user, multi-purpose facility for materials science research. One experiment within the MSRF will be the Quench Module Insert (QMI), a high-temperature furnace with unique capabilities for processing different classes of materials. The primary functions of the QMI furnace are to melt, directionally solidify, and quench metallic samples, providing data to aid in understanding the effects of the microgravity environment on the characteristics of these processed metals. The QMI houses sealed individual sample ampoules containing material to be processed. Quenching of the samples in the QMI furnace is accomplished by releasing low-melting-point metallic shoes into contact with the outside of the sample ampoule, dissipating heat and cooling the sample inside. The impact from this method of quench will induce sample vibrations which could be large enough to adversely affect sample quality. Utilizing breadboard hardware, the sample quench sequence, releasing the shoes, was conducted. Data was collected from accelerometers located on the breadboard sample cartridge, indicating the maximum acceleration achieved by the sample. The primary objective of the test described in this presentation was to determine the acceleration imparted on the sample by the shoe contact. From this information, the science community can better assess whether this method of quench will allow them to obtain the data they need.

Gattis, Christy↗

NASA NTRS1993

Spring-Tab Lock Washer

Improved spring-tab lock washer offers alternative to such positive-locking devices as cotter pins and lock wires and to conventional split-ring lock washers. Does not dig into fastened parts with sharp edges; less likely to inflict scratches causing cracks. Contains three winglike spring tabs and three alignment pips, pressed into mating dimples in surface of part to be fastened. Spring tabs on lock washer allow only clockwise rotation (tightening) of bolt or nut.

Finckenor, Jeff↗