Engineering topics

Rogers, Patrick R.

Publications and source records attributed to Rogers, Patrick R..

4 records

NASA NTRS2006

An Overview of Spray-On Foam Insulation Applications on the Space Shuttle's External Tank: Foam Applications and Foam Shedding Mechanisms

The Columbia Accident Investigation Board (CAIB) concluded that the cause of the tragic loss of the Space Shuttle Columbia and its crew was a breach in the thermal protection system on the leading edge of the left wing. The breach was initiated by a piece of insulating foam that separated from the left bipod ramp of the External Tank and struck the wing in the vicinity of the lower half of Reinforced Carbon-Carbon panel No. 8 at 81.9 seconds after launch. The CAIB conclusion has spawned numerous studies to identify the cause of and factors influencing foam shedding and foam debris liberation from the External Tank during ascent. The symposium on the Thermo-mechanics and Fracture of Space Shuttle External Tank Spray-On Foam Insulation is a collection of presentations that discuss the physics and mechanics of the ET SOFI with the objective of improving analytical and numerical methods for predicting foam thermo-mechanical and fracture behavior. This keynote presentation sets the stage for the presentations contained in this symposium by introducing the audience to the various types of SOFI applications on the Shuttle s External Tank and by discussing the various mechanisms that are believed to be the cause of foam shedding during the Shuttle s ascent to space

Sullivan, Roy M.↗

NASA NTRS2005

Structural Verification of the Redesigned Space Shuttle Bipod Foam Closeout

This document outlines the structural verification approach for the Space Shuttle External Tank Forward Bipod Foam Closeout. Due to the Space Shuttle Columbia accident, debris has become a major concern. The intent of the structural verification is to ensure that any debris shed from the bipod is within acceptable limits. Since cohesive failure due to internal defects was identified as the most likely cause of the STS-107 bipod ramp foam failure, verification for this failure mode receives particular emphasis. However, all failure modes for TPS are considered and appropriate verification rationale is developed for each failure mode. Figure 1 depicts the structural verification of a production design where analysis and test are the primary methods of verification. It can be seen that the successful completion of structural verification is dependent on three main areas: 1. Production process control and quality assurance must ensure that test articles and/or analytical models are representative of (or conservatively envelope) production hardware in terms of geometry, materials and processing. Variability and defects must be considered. 2. Flight environments must be sufficiently characterized to bound driving environments for all failure modes. Applied environments, either test or analytical, must be representative of flight environments and have a load factor that satisfies design requirements. 3. Structural verification must include all failure modes. A comprehensive list of failure modes and the underlying failure mechanisms has been generated based on flight and test experience. Verification tests and / or analyses must address each failure mode. ET TPS Verification is accomplished by a combination of analysis, test, and similarity.

Poole, Eric L.↗

NASA NTRS1998

Wide Panel Testing Technique for Evaluating Repair Weld Strengths

This paper describes a new tensile testing technique for evaluating the overall effect of a repair weld on the strength of a welded joint. Previously, repair weld strengths have been evaluated using one-inch width tensile specimens, but this technique does not capture all of the effects that result from a repair. The new technique involves testing of "wide panel" tensile specimens which contain the full length of a repair weld within a longer initial weld, allowing the specimen to capture the combined effects of residual stresses, local strength degradation, and load redistribution around a repair. The development of strains in the repair area of standard aluminum alloy specimens and new high-performance aluminum-lithium alloy specimens was observed and evaluated using photoelastic material. The results of this evaluation show an increased sensitivity to repair welding residual stresses in the aluminum-lithium alloy specimens.

Rogers, Patrick R.↗

NASA NTRS1993

Machined Structural Panels With Integral End Fittings

Flat, cylindrical, or otherwise-shaped unitary machined corrugated metal panels used as structural skins, according to proposal. Machined plates offer advantages over such conventional lightweight structural components as formed corrugated sheets, composite panels, and honeycomb panels. Include integrally machined end fittings and are lighter, less prone to failure, easier to design and analyze, and offer greater stiffness. No additional stringers or frames needed for reinforcement.

Redmon, John W., Jr.↗