Engineering topics

Rojas, R. G.

Publications and source records attributed to Rojas, R. G..

12 records

NASA NTRS1994

Electromagnetic on-aircraft antenna radiation in the presence of composite plates

The UTD-based NEWAIR3 code is modified such that it can model modern aircraft by composite plates. One good model of conductor-backed composites is the impedance boundary condition where the composites are replaced by surfaces with complex impedances. This impedance-plate model is then used to model the composite plates in the NEWAIR3 code. In most applications, the aircraft distorts the desired radiation pattern of the antenna. However, test examples conducted in this report have shown that the undesired scattered fields are minimized if the right impedance values are chosen for the surface impedance plates.

Kan, S. H-T.↗

NASA NTRS1993

Performance of traffic-alert collision avoidance (TCAS) antennas in the presence of scatterers

The performance of two TCAS systems is studied in the presence of electromagnetic scatterers. TCAS is an aircraft mounted angle of arrival (AOA) system, which estimates the bearing of a signal transmitted from a mode-S transponder on another nearby aircraft (intruder). Two systems are studied: (1) Comparison of Relative Amplitude system (CRA), and (2) Spiral Phase Antenna (SPA). The CRA antenna receives the reply via four switched beams. The bearing is estimated by comparing the amplitudes of the received signal. The SPA is based on the phase interferometer, which utilizes the received phase via sum and difference beams. The AOA is computed by comparing the reply with similar values on a calibration table, which is generated by modeling the TCAS antenna on the bare fuselage of a Boeing 727-200. The antenna patterns for the TCAS are found via high frequency methods based on the Uniform Geometric theory of Diffraction (UTD). By minimizing the standard deviation of the bearing error in a specified angular sector, optimal locations for top and bottom mounted TCAS antennas are found on the Boeing 727-200, 737-300 and 747-200 airframes. It will be shown that the overall bearing errors of the amplitude system are consistently smaller than the spiral phase TCAS. The effect of two types of nearby scatterers--antennas, and engine inlets--is studied. The AT741 L-band blade, DMC60-1 VHF Communication antenna were chosen as being representative antenna interference examples. Models are derived for the blades via a moment method analysis followed by a least squares procedure to synthesize the scattering patterns. Studies were conducted to estimate the minimum separation between the two antennas for acceptable operation. It will be shown that the spiral phase TCAS is adversely affected by the presence of a blade antenna. The amplitude system does not suffer from this limitation, especially for the forward look angles which are of most interest here. A model to represent the inlet scattering is based on the multiple scattering method and UTD. The engine on top of the B727-200 fuselage is modeled by a terminated circular waveguide. Then, the effect of moving the antenna forward on the fuselage is studied. It is again shown that the performance of the amplitude system is superior.

Sampath, K. S.↗

NASA NTRS1993

Operation of the helicopter antenna radiation prediction code

HARP is a front end as well as a back end for the AMC and NEWAIR computer codes. These codes use the Method of Moments (MM) and the Uniform Geometrical Theory of Diffraction (UTD), respectively, to calculate the electromagnetic radiation patterns for antennas on aircraft. The major difficulty in using these codes is in the creation of proper input files for particular aircraft and in verifying that these files are, in fact, what is intended. HARP creates these input files in a consistent manner and allows the user to verify them for correctness using sophisticated 2 and 3D graphics. After antenna field patterns are calculated using either MM or UTD, HARP can display the results on the user's screen or provide hardcopy output. Because the process of collecting data, building the 3D models, and obtaining the calculated field patterns was completely automated by HARP, the researcher's productivity can be many times what it could be if these operations had to be done by hand. A complete, step by step, guide is provided so that the researcher can quickly learn to make use of all the capabilities of HARP.

Braeden, E. W.↗

NASA NTRS1991

Automated composite ellipsoid modelling for high frequency GTD analysis

The preliminary results of a scheme currently being developed to fit a composite ellipsoid to the fuselage of a helicopter in the vicinity of the antenna location are discussed under the assumption that the antenna is mounted on the fuselage. The parameters of the close-fit composite ellipsoid would then be utilized as inputs into NEWAIR3, a code programmed in FORTRAN 77 for high frequency Geometrical Theory of Diffraction (GTD) Analysis of the radiation of airborne antennas.

Sze, K. Y.↗

NASA NTRS1990

The Helicopter Antenna Radiation Prediction Code (HARP)

The first nine months effort in the development of a user oriented computer code, referred to as the HARP code, for analyzing the radiation from helicopter antennas is described. The HARP code uses modern computer graphics to aid in the description and display of the helicopter geometry. At low frequencies the helicopter is modeled by polygonal plates, and the method of moments is used to compute the desired patterns. At high frequencies the helicopter is modeled by a composite ellipsoid and flat plates, and computations are made using the geometrical theory of diffraction. The HARP code will provide a user friendly interface, employing modern computer graphics, to aid the user to describe the helicopter geometry, select the method of computation, construct the desired high or low frequency model, and display the results.

Klevenow, F. T.↗

NASA NTRS1990

Modelling and performance analysis of four and eight element TCAS

This semi-annual report describes the work performed during the period September 1989 through March 1990. The first section presents a description of the effect of the engines of the Boeing 737-200 on the performance of a bottom mounted eight-element traffic alert and collision avoidance system (TCAS). The second section deals exclusively with a four element TCAS antenna. The model obtained to simulate the four element TCAS and new algorithms developed for studying its performance are described. The effect of location on its performance when mounted on top of a Boeing 737-200 operating at 1060 MHz is discussed. It was found that the four element TCAS generally does not perform as well as the eight element TCAS III.

Sampath, K. S.↗

NASA NTRS1989

Improved computer simulation of the TCAS 3 circular array mounted on an aircraft

The Traffic advisory and Collision Avoidance System (TCAS) is being developed by the Federal Aviation Administration (FAA) to assist aircraft pilots in mid-air collision avoidance. This report concentrates on the computer simulation of the enchanced TCAS 2 systems mounted on a Boeing 727. First, the moment method is used to obtain an accurate model for the enhanced TCAS 2 antenna array. Then, the OSU Aircraft Code is used to generate theoretical radiation patterns of this model mounted on a simulated Boeing 727 model. Scattering error curves obtained from these patterns can be used to evaluate the performance of this system in determining the angular position of another aircraft with respect to the TCAS-equipped aircraft. Finally, the tracking of another aircraft is simulated when the TCAS-equipped aircraft follows a prescribed escape curve. In short, the computer models developed in this report have generality, completeness and yield reasonable results.

Rojas, R. G.↗

NASA NTRS1987

A study of the TCAS 2 collision avoidance system mounted on a Boeing 737 aircraft

The purpose of this report is to determine the effects of scattering from major aircraft structures on the TCAS 2 collision avoidance system mounted on a Boeing 737. It is found that the major source of scattering for angles of observation above the horizon is the vertical stabilizer and that its effect may be greatly reduced by mounting the TCAS 2 array close to the nose of the aircraft. In addition, by mounting the array close to the nose, the effects of fuselage blockage on the array patterns at elevation angles below the horizon may be greatly reduced in the forward direction.

Grandchamp, B.↗

NASA NTRS1987

Simulation of an enhanced TCAS 2 system in operation

Described is a computer simulation of a Boeing 737 aircraft equipped with an enhanced Traffic and Collision Avoidance System (TCAS II). In particular, an algorithm is developed which permits the computer simulation of the tracking of a target airplane by a Boeing 373 which has a TCAS II array mounted on top of its fuselage. This algorithm has four main components: namely, the target path, the noise source, the alpha-beta filter, and threat detection. The implementation of each of these four components is described. Furthermore, the areas where the present algorithm needs to be improved are also mentioned.

Rojas, R. G.↗

NASA NTRS1986

A study of a collision avoidance system mounted on a curved ground plane

Research conducted on a traffic advisory and collision avoidance system (TCAS 2) mounted on a curved ground plane is described. It is found that a curved finite ground plane can be used as a good simulation model for the fuselage of an aircraft but may not be good enough to model a whole aircraft due to the shadowing of the vertical stabilizer, wings, etc. The surface curvature of this curved disc significantly affects the monopulse characteristics in the azimuth plane but not as much in the elevation plane. These variations of the monopulse characteristics verify the need of a lookup table for the 64 azimuth beam positions. The best location of a TCAS 2 array on a Boeing 737 is to move it as far from the vertical stabilizer as possible.

Law, P. H.↗

NASA NTRS1985

Simulation of the enhanced traffic alert and collision avoidance system (TCAS 2)

The OSU aircraft code is used to analyze and simulate the TCAS 2 circular array which is mounted on the fuselage of a Boeing 737 aircraft. It is shown that the sum and difference patterns radiated by the circular array are distorted by the various structures of the aircraft, i.e., wings, tail, etc. Furthermore, monopulse curves are calculated and plotted for several beam positions and THETA angles. As expected, the worst cases of distortion occur when the beams are pointed toward the tail of the aircraft.

Rojas, R. G.↗

NASA NTRS1982

Analysis of airborne antenna patterns

The status of various efforts in support of the development of computer codes to analyze the radiation patterns of general aviation aircraft and simulate private aircraft is reported. Because of the significant amount of energy scattered by the windshield of private aircraft, a method is being developed to treat high frequency scattering by thin dielectric layers. To treat such aircraft at lower frequencies, i.e., where the aircraft surface area is less than 10 square wavelengths, a moment method code is being modified. The problem of plane (or surface) wave diffraction by the dielectric half plane is constructed and discussed.

Rojas, R. G.↗