Engineering topics

Romberg, Stian K.

Publications and source records attributed to Romberg, Stian K..

4 records

DOE OSTI2022

Large-scale reactive thermoset printing: Complex interactions between temperature evolution, viscosity, and cure shrinkage

Thermoset composites are strong candidates for large-scale material extrusion additive manufacturing (AM). However, uncured thermoset composites become unstable as print height increases. Here, chemical initiation of vinyl ester immediately before deposition was used to suppress collapse and enable large-scale thermoset printing. Structural stability was assessed by printing thin walls at various layer times and monitoring thermal gradients with an infrared camera. Stable printing was observed at a layer time of 4.50 min, approximately half the gel time of the material (8 min). Self-weight collapse occurred at short layer time (0.68 min), whereas warpage occurred at long layer time (6.50 min). Here, a new behavior was discovered at intermediate layer time (2.25 min) where the heat generated by the reaction causes new, un-gelled layers to flow. Forced convection eliminates this behavior, stabilizing the 2.25-min layer time print. These findings motivated development of a less exothermic material system, which was used to print a large-scale mold and demonstrate the value of this understanding. By presenting these challenges of large-scale reactive thermoset AM for the first time, this work motivates focused studies of the complex interplay between rheological, thermal, and chemical behaviors to improve the feasibility of large-scale thermoset AM. Tensile properties of the printed material were also measured. Longitudinal and transverse elastic moduli are 3.79 and 2.95 GPa, respectively, and corresponding tensile strengths are 36.11 and 18.83 MPa. The glass transition temperature is 93.13 °C.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Structural stability of thin overhanging walls during material extrusion additive manufacturing of thermoset-based ink

Recent developments have enabled material extrusion additive manufacturing of thermoset-based composite inks on the large scale. In addition, printing out-of-plane components is of broad interest to the polymer material extrusion community. Here, we address some of the challenges associated with both large-scale and out-of-plane thermoset material extrusion additive manufacturing by studying the height at which thin overhanging walls collapse. Walls at a range of overhang angles were printed until they collapsed. An optical camera captured the profile of each wall throughout the print, allowing the collapse height to be identified and the geometric fidelity to the programmed angle to be evaluated. Using previously measured rheological properties, predictive models were generated to approximate the collapse height and profile of the deflected walls. First, an analytical model was created to predict the height at which the walls would yield. The analytical model assumes the walls exhibit a perfectly linear profile; however, experiments proved this assumption to be false. Therefore, a finite element simulation was developed to account for the elastic deflection that occurs during printing. The finite element simulation predicts both the yield height and the deflected profile after the deposition of each layer. For the properties of the thermoset ink used here, the yield height predicted by the analytical model and finite element simulation are virtually identical. These predictions match experimental data reasonably well, but minor errors are observed. Accounting for the fully plastic moment appears to explain the small mismatch between experimental data and predictions. Additionally, the finite element simulation provides an excellent prediction of the deflected profile before the wall begins to collapse. Finally, by demonstrating that the collapse height and deflected profile of thin overhanging walls can be predicted, this work illustrates how the soft viscoelastic properties of thermoset-based composite inks limit the scale of a key feature required to print some nonplanar components. It also provides a basis to tailor in-process curing systems to suppress deflection and collapse of thin overhanging walls.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Carbon Fiber and Syntactic Foam Hybrid Materials via Core–Shell Material Extrusion Additive Manufacturing

Abstract Biological materials often employ hybrid architectures, such as the core–shell (C–S) motif present in porcupine quills and plant stems, to achieve unique specific properties and performance. Drawing inspiration from these natural materials, a new method to fabricate lightweight and stiff C–S architected filaments is reported. Specifically, a C–S printhead conducive to printing highly loaded fiber‐filled inks, as well as a new low‐density syntactic foam ink, are utilized to 3D‐print C–S architectures consisting of a syntactic epoxy foam core surrounded by a stiff carbon fiber‐reinforced epoxy composite shell. Effective printing of test specimens and structures with controlled geometry, composition, and architecture is demonstrated. The new foam ink exhibits density as low as 0.68 g cm −3 and C–S structures exhibit up to 25% higher specific flexural stiffness ( E 1/3 /ρ) than either constituent alone. Finally, a new mechanical model is presented to predict this performance improvement while accounting for potential eccentricity of the core.

Pack, Robert C.↗

DOE OSTI2020

Linking thermoset ink rheology to the stability of 3D-printed structures

Thermoset polymer composites show promise for additive manufacturing (AM) applications to address some of the limitations of the more widely used thermoplastic feedstock materials. Thermosets offer attractive mechanical properties while providing excellent interlayer bonding, high thermal and chemical stability, and reduced energy consumption as a result of deposition at room temperature. However, since thermoset resins rely on a crosslinking reaction to solidify, rather than quickly cooling like thermoplastics, viscoelastic properties must be relied upon to maintain deposited shape after deposition until crosslinking can occur. This fact has not impeded development and characterization of new thermoset feedstocks on the small scale, but recent efforts to increase scale of thermoset printing have highlighted issues with structural stability under self-weight. This study addresses issues of self-weight by investigating the mechanisms that cause collapse of tall, thin printed walls. Using nanoclay- and fumed silica-filled epoxy feedstocks, this work compares the collapse height for printed walls to stability models based on yielding and buckling mechanics. Inputs for these models – shear yield stress and storage modulus – were taken directly from parallel plate rheometry measurements. Model predictions were found to be in good agreement with experimental results, where both yielding and buckling behavior were observed, provided the rheological properties after a shear excursion were used as inputs. This work establishes a direct link between basic rheological properties of the feedstock, geometry of the printed object, and achievable height. Overall, the results presented highlight the importance of understanding recovery behavior in thermoset feedstocks and provide valuable guidance on the development of more effective direct-ink writing feedstock materials.

36 MATERIALS SCIENCE↗