Lithium sputtering from lithium-coated plasma facing components in the NSTX divertor
Not Available
Engineering topics
Publications and source records attributed to Roquemore, A L.
Not Available
Rutherford backscattering of energetic particles can be used to determine the thickness of a coating of a low-Z material over a heavier substrate. Simulations indicate that 5 MeV alpha particles from an {sup 241}Am source can be used to measure the thickness of a Li coating on Mo tiles between 0.5 and 15 μm thick. Using a 0.1 mCi source, a thickness measurement can be accomplished in 2 h of counting. This technique could be used to measure any thin, low-Z material coating (up to 1 mg/cm{sup 2} thick) on a high-Z substrate, such as Be on W, B on Mo, or Li on Mo. By inserting a source and detector on a moveable probe, this technique could be used to provide an in situ measurement of the thickness of Li coating on NSTX-U Mo tiles. A test stand with an alpha source and an annular solid-state detector was used to investigate the measurable range of low-Z material thicknesses on Mo tiles.
Abstract not provided
Abstract not provided
Experimental results from NSTX indicate that the snowflake divertor (D. Ryutov, Phys. Plasmas 14, 064502 (2007)) may be a viable solution for outstanding tokamak plasma-material interface issues. Steady-state handling of divertor heat flux and divertor plate erosion remains to be critical issues for ITER and future concept devices based on conventional and spherical tokamak geometry with high power density divertors. Experiments conducted in 4-6 MW NBI-heated H-mode plasmas in NSTX demonstrated that the snowflake divertor is compatible with high-confinement core plasma operation, while being very effective in steady-state divertor heat flux mitigation and impurity reduction. A steady-state snowflake divertor was obtained in recent NSTX experiments for up to 600 ms using three divertor magnetic coils. The high magnetic flux expansion region of the scrape-off layer (SOL) spanning up to 50% of the SOL width {lambda}{sub q} was partially detached in the snowflake divertor. In the detached zone, the heat flux profile flattened and decreased to 0.5-1 MW/m{sup 2} (from 4-7 MW/m{sup 2} in the standard divertor) indicative of radiative heating. An up to 50% increase in divertor, P{sub rad} in the snowflake divertor was accompanied by broadening of the intrinsic C III and C IV radiation zones, and a nearly order of magnitude increase in divertor high-n Balmer line emission indicative of volumetric recombination onset. Magnetic reconstructions showed that the x-point connection length, divertor plasma-wetted area and divertor volume, all critical parameters for geometric reduction of deposited heat flux, and increased volumetric divertor losses were significantly increased in the snowflake divertor, as expected from theory.
A novel imaging adaptor providing the capability to extend a standard single-band infrared (IR) camera into a two-color or dual-band device has been developed for application to high-speed IR thermography on the National Spherical Tokamak Experiment (NSTX). Temperature measurement with two-band infrared imaging has the advantage of being mostly independent of surface emissivity, which may vary significantly in the liquid lithium divertor installed on NSTX as compared to that of an all-carbon first wall. In order to take advantage of the high-speed capability of the existing IR camera at NSTX (1.6-6.2 kHz frame rate), a commercial visible-range optical splitter was extensively modified to operate in the medium wavelength and long wavelength IR. This two-band IR adapter utilizes a dichroic beamsplitter, which reflects 4-6 {mu}m wavelengths and transmits 7-10 {mu}m wavelength radiation, each with >95% efficiency and projects each IR channel image side-by-side on the camera's detector. Cutoff filters are used in each IR channel, and ZnSe imaging optics and mirrors optimized for broadband IR use are incorporated into the design. In-situ and ex-situ temperature calibration and preliminary data of the NSTX divertor during plasma discharges are presented, with contrasting results for dual-band vs. single-band IR operation.
Abstract not provided
Small, nonaxisymmetric magnetic perturbations generated by external coils have been found to break the axisymmetry of heat and particle flux deposition pattern in the divertor area in the National Spherical Torus Experiment (NSTX). This breaking by the applied 3-D field causes strike point splitting that is represented as local peaks and valleys in the divertor profiles. In case of n = 3 fields application, the broken toroidal symmetry of the divertor profile shows 120 deg. of spatial periodicity while data for n = 1 fields provide a fully nonaxisymmetric heat and particle deposition. Field line tracing showed good agreement with the measured heat and particle flux profiles. Higher toroidal mode number (n = 3) of the applied perturbation produced more and finer striations in the divertor profiles than in the lower mode number (n = 1) case. Following the previous result of the intrinsic strike point splitting by the n = 3 error fields [Nucl. Fusion 50, 045010 (2010); J. Nucl. Mater. (2011), doi:10.1016/j.jnucmat.2011.01.115], result of the connection length profile from field line tracing identifies intrinsic error field as a possible source of the intrinsic splitting. In determining the strike point splitting pattern, q{sub 95} is found to play an important role; higher q{sub 95} produces finer striations and induces higher fraction of heat flux to flow through the split strike point channels. Higher pedestal electron collisionality also made the striations in the D{sub {alpha}} profile more pronounced in the given range of collisionality variation. The radial location of local peaks in the profiles during the triggered edge localized modes (ELMs) by the applied n = 3 fields stays similar before and after the application. This shows that the heat flux from the triggered ELMs follows the mode number of the applied perturbation. The external magnetic perturbation can reattach detached divertor plasma, but this can be overcome by detaching the plasma with additional divertor gas puffing.
The ability to manage inventories of carbon, tritium, and high-Z elements in fusion plasmas depends on means for effective dust removal. A dust conveyor, based on a moving electrostatic potential well, was tested with particles of tungsten, carbon, glass, and sand. A digital microscope imaged a representative portion of the conveyor, and dust particle size and volume distributions were derived before and after operation. About 10 mm{sup 3} volume of carbon and tungsten particles were moved in under 5 s. The highest driving amplitude tested of 3 kV was the most effective. The optimal driving frequency was 210 Hz (maximum tested) for tungsten particles, decreasing to below 60 Hz for the larger sand particles. Measurements of particle size and volume distributions after 10 and 100 cycles show the breaking apart of agglomerated carbon and the change in particle distribution over short timescales (<1 s).
Discharges formed by transient coaxial helicity injection (CHI) in the National Spherical Torus Experiment (NSTX) have attained peak currents of 300 kA for the first time. CHI-started discharges are coupled to induction, and ramped up to over 1 MA. Up to an additional 400 kA of toroidal current is produced, compared with discharges with the same inductive drive without CHI. These CHI-inductively coupled discharges demonstrate flux savings over standard NSTX inductive-only discharges, requiring significantly less transformer flux to reach 1 MA of toroidal current, as well as exhibiting higher elongation and lower internal inductance. These results indicate the potential for substantial current generation capability by CHI in NSTX and in future toroidal devices.
Fast cameras already installed on the National Spherical Torus Experiment (NSTX) have be equipped with near-infrared (NIR) filters in order to measure the surface temperature in the lower divertor region. Such a system provides a unique combination of high speed (> 50 kHz) and wide fi eld-of-view (> 50% of the divertor). Benchtop calibrations demonstrated the system's ability to measure thermal emission down to 330 oC. There is also, however, signi cant plasma light background in NSTX. Without improvements in background reduction, the current system is incapable of measuring signals below the background equivalent temperature (600 - 700 oC). Thermal signatures have been detected in cases of extreme divertor heating. It is observed that the divertor can reach temperatures around 800 oC when high harmonic fast wave (HHFW) heating is used. These temperature profiles were fi t using a simple heat diffusion code, providing a measurement of the heat flux to the divertor. Comparisons to other infrared thermography systems on NSTX are made.
Divertor heat and particle flux profiles are modified by externally imposed non-axisymmetric magnetic perturbations in the National Spherical Torus Experiment. The applied 3-D field causes strike point splitting that is represented as local peaks and valleys in the divertor profiles. The plasma response in an ideal perturbed equilibrium approach was included in the field line tracing by taking account of the B-field generated by the plasma current up to a certain fraction of normalized flux inside the separatrix and being superposed to the vacuum field. The inclusion of this type of plasma response does not significantly affect the location and spacing of the split strike points at the divertor surface. A modest level of divertor profile modification is found to occur even without the application of 3-D fields in certain high triangularity (delta = 0.65-0.8) discharges, with the location of local peaks and valleys same before and after the application. The intrinsic error field from the non-circularity of PF5 coil is known to have primarily n = 3 component in NSTX and was modeled to be included in the vacuum field line tracing. The produced puncture plot of the field line along with the connection length profile shows that the radial location of local peaks agrees well with the measurement, identifying intrinsic error field as a possible source of intrinsic strike point splitting. The radial location of local peaks in the profiles during the triggered ELM by the applied n = 3 field is the same before and after the 3-D field application. This shows that the heat flux from the triggered ELMs appears to follow the imposed n = 3 field structure.
NSTX experiments have explored lithium evaporated on a graphite divertor and other plasma-facing components in both L- and H- mode confinement regimes heated by high-power neutral beams. Improvements in plasma performance have followed these lithium depositions, including a reduction and eventual elimination of the HeGDC time between discharges, reduced edge neutral density, reduced plasma density, particularly in the edge and the SOL, increased pedestal electron and ion temperature, improved energy confinement and the suppression of ELMs in the H-mode. However, with improvements in confinement and suppression of ELMs, there was a significant secular increase in the effective ion charge Z(eff) and the radiated power in H-mode plasmas as a result of increases in the carbon and medium-Z metallic impurities. Lithium itself remained at a very low level in the plasma core, < 0.1%. Initial results are reported from operation with a Liquid Lithium Divertor (LLD) recently installed. (C) 2010 Elsevier B.V. All rights reserved.
The first real-time detection of surface dust inside a tokamak was made using an electrostatic dust detector. A fine grid of interlocking circuit traces was installed in the NSTX vessel and biased to 50 V. Impinging dust particles created a temporary short circuit and the resulting current pulse was recorded by counting electronics. The techniques used to increase the detector sensitivity by a factor of x10 000 to match NSTX dust levels while suppressing electrical pickup are presented. The results were validated by comparison to laboratory measurements, by the null signal from a covered detector that was only sensitive to pickup, and by the dramatic increase in signal when Li particles were introduced for wall conditioning purposes.
This paper describes the first observations in the National Spherical Torus Experiment (NSTX) [S. M. Kaye et al., Phys. Plasmas 8, 1977 (2001)] of ''quiet periods'' in the edge turbulence preceding the low-to-high (L-H) mode transition, as diagnosed by the gas puff imaging (GPI) diagnostic near the outer midplane separatrix. During these quiet periods the GPI D{sub {alpha}}light emission pattern was transiently similar to that seen during H-mode, i.e., with a relatively small fraction of the GPI light emission located outside the separatrix. These quiet periods had a frequency of {approx}3 kHz for at least 30 ms before the L-H transition, and were correlated with changes in the direction of the local poloidal velocity. The GPI turbulence images were also analyzed to obtain an estimate for the dimensionless poloidal shearing S=(dV{sub p}/dr)(L{sub r}/L{sub p}){tau}. The values of S were strongly modulated by the quiet periods but did not significantly vary during the {approx}30 ms preceding the L-H transition. Since neither the quiet periods nor the shear flow increased immediately preceding the L-H transition, neither of these appears to be the trigger for this transition, at least for these cases in NSTX.
The use of lithium-coated plasma facing components for plasma density control is studied in the National Spherical Torus Experiment (NSTX). A recently installed liquid lithium divertor (LLD) module has a porous molybdenum surface, separated by a stainless steel liner from a heated copper substrate. Lithium is deposited on the LLD from two evaporators. Two new spectroscopic diagnostics are installed to study the plasma surface interactions on the LLD: (1) A 20-element absolute extreme ultraviolet (AXUV) diode array with a 6 nm bandpass filter centered at 121.6 nm (the Lyman-{alpha} transition) for spatially resolved divertor recycling rate measurements in the highly reflective LLD environment, and (2) an ultraviolet-visible-near infrared R=0.67 m imaging Czerny-Turner spectrometer for spatially resolved divertor D I, Li I-II, C I-IV, Mo I, D{sub 2}, LiD, CD emission and ion temperature on and around the LLD module. The use of photometrically calibrated measurements together with atomic physics factors enables studies of recycling and impurity particle fluxes as functions of LLD temperature, ion flux, and divertor geometry.
A high-resolution x-ray imaging crystal spectrometer, whose concept was tested on NSTX and Alcator C-Mod, is being designed for the large helical device (LHD). This instrument will record spatially resolved spectra of helium-like Ar{sup 16+} and will provide ion temperature profiles with spatial and temporal resolutions of <2 cm and {>=}10 ms, respectively. The spectrometer layout and instrumental features are largely determined by the magnetic field structure of LHD. The stellarator equilibrium reconstruction codes, STELLOPT and PIES, will be used for the tomographic inversion of the spectral data.
The recent availability of broadband microwave quadrature mixers in the Ka-band (28-40 GHz) of frequencies has allowed the fabrication of low-cost direct-conversion detection circuits for use in the variable-frequency correlation reflectometer on the National Spherical Torus eXperiment (NSTX). The quadrature receiver in this case can be implemented as a simple homodyne circuit, without the complication of a single-sideband modulator or a feedforward tracking circuit present in more typical designs. A pair of direct-conversion receivers is coupled with broadband microwave voltage-controlled oscillators to construct a flexible dual-channel radar system with a fast frequency settling time of {approx}160 {mu}s. A detailed description of the design and a full characterization of the hardware are provided. Examples of turbulence measurements from radial and poloidal correlation reflectometry on NSTX using a poloidal array of antennas (oriented normal to the magnetic flux surfaces for conventional reflectometry) are presented.