Engineering topics

Rosen, B. W.

Publications and source records attributed to Rosen, B. W..

At least 19 records

NASA NTRS1992

Failure analysis of thick composite cylinders under external pressure

Failure of thick section composites due to local compression strength and overall structural instability is treated. Effects of material nonlinearity, imperfect fiber architecture, and structural imperfections upon anticipated failure stresses are determined. Comparisons with experimental data for a series of test cylinders are described. Predicting the failure strength of composite structures requires consideration of stability and material strength modes of failure using linear and nonlinear analysis techniques. Material strength prediction requires the accurate definition of the local multiaxial stress state in the material. An elasticity solution for the linear static analysis of thick anisotropic cylinders and rings is used herein to predict the axisymmetric stress state in the cylinders. Asymmetric nonlinear behavior due to initial cylinder out of roundness and the effects of end closure structure are treated using finite element methods. It is assumed that local fiber or ply waviness is an important factor in the initiation of material failure. An analytical model for the prediction of compression failure of fiber composites, which includes the effects of fiber misalignments, matrix inelasticity, and multiaxial applied stresses is used for material strength calculations. Analytical results are compared to experimental data for a series of glass and carbon fiber reinforced epoxy cylinders subjected to external pressure. Recommendations for pretest characterization and other experimental issues are presented. Implications for material and structural design are discussed.

Caiazzo, A.↗

NASA NTRS1983

Guidelines for composite materials research related to general aviation aircraft

Guidelines for research on composite materials directed toward the improvement of all aspects of their applicability for general aviation aircraft were developed from extensive studies of their performance, manufacturability, and cost effectiveness. Specific areas for research and for manufacturing development were identified and evaluated. Inputs developed from visits to manufacturers were used in part to guide these evaluations, particularly in the area of cost effectiveness. Throughout the emphasis was to direct the research toward the requirements of general aviation aircraft, for which relatively low load intensities are encountered, economy of production is a prime requirement, and yet performance still commands a premium. A number of implications regarding further directions for developments in composites to meet these requirements also emerged from the studies. Chief among these is the need for an integrated (computer program) aerodynamic/structures approach to aircraft design.

Dow, N. F.↗

NASA NTRS1981

Thermomechanical response of Gr/Pi composites

The effects of temperature changes upon the stresses and strains in composite laminates having carbon fibers in a polyimide matrix were evaluated. Composites having laminae in which there were nonlinear stress-strain relations for stresses transverse to the fibers and for axial shear stresses were treated. Material properties were considered to be temperature dependent. Separately, the effects of laminae viscoelastic response were also treated. The results suggest that, for this material, nonlinearities due either to stress or time dependent effects do not appear to be of major practical importance for conventional high temperature composite structures.

Rosen, B. W.↗

NASA NTRS1979

Development of a realistic stress analysis for fatigue analysis of notched composite laminates

A finite element stress analysis which consists of a membrane and interlaminar shear spring analysis was developed. This approach was utilized in order to model physically realistic failure mechanisms while maintaining a high degree of computational economy. The accuracy of the stress analysis predictions is verified through comparisons with other solutions to the composite laminate edge effect problem. The stress analysis model was incorporated into an existing fatigue analysis methodology and the entire procedure computerized. A fatigue analysis is performed upon a square laminated composite plate with a circular central hole. A complete description and users guide for the computer code FLAC (Fatigue of Laminated Composites) is included as an appendix.

Humphreys, E. A.↗

NASA NTRS1979

Nonlinear effects on composite laminate thermal expansion

Analyses of Graphite/Polyimide laminates shown that the thermomechanical strains cannot be separated into mechanical strain and free thermal expansion strain. Elastic properties and thermal expansion coefficients of unidirectional Graphite/Polyimide specimens were measured as a function of temperature to provide inputs for the analysis. The + or - 45 degrees symmetric Graphite/Polyimide laminates were tested to obtain free thermal expansion coefficients and thermal expansion coefficients under various uniaxial loads. The experimental results demonstrated the effects predicted by the analysis, namely dependence of thermal expansion coefficients on load, and anisotropy of thermal expansion under load. The significance of time dependence on thermal expansion was demonstrated by comparison of measured laminate free expansion coefficients with and without 15 day delay at intermediate temperature.

Hashin, Z.↗

NASA NTRS1977

Fatigue of notched fiber composite laminates - Analytical and experimental evaluation

Axial cracking in the load direction and transverse cracking across notched boron/epoxy laminate specimens subjected to tension/tension fatigue loading are studied both theoretically and experimentally. The fatigue analysis, which allows for the computation of residual strength and the determination of the preferred mode of crack propagation, is reviewed; static and fatigue data for boron/epoxy lamina are investigated with the aim of characterizing fatigue growth and residual strength as a function of the number of load cycles. It is suggested that correlation between the theory and the experiment may be limited by lack of a capability to predict the growth of delaminations.

Kulkarni, S. V.↗

NASA NTRS1975

An investigation of the compressive strength of Kevlar 49/epoxy composites

Tests were performed to evaluate the effect of a wide range of variables including matrix properties, interface properties, fiber prestressing, secondary reinforcement, and others on the ultimate compressive strength of Kevlar 49/epoxy composites. Scanning electron microscopy is used to assess the resulting failure surfaces. In addition, a theoretical study is conducted to determine the influence of fiber anisotropy and lack of perfect bond between fiber and matrix on the shear mode microbuckling. The experimental evaluation of the effect of various constituent and process characteristics on the behavior of these unidirectional composites in compression did not reveal any substantial increase in strength. However, theoretical evaluations indicate that the high degree of fiber anisotropy results in a significant drop in the predicted stress level for internal instability. Scanning electron microscope data analysis suggests that internal fiber failure and smooth surface debonding could be responsible for the measured low compressive strengths.

Kulkarni, S. V.↗

NASA NTRS1975

Fatigue of notched fiber composite laminates. Part 1: Analytical model

A description is given of a semi-empirical, deterministic analysis for prediction and correlation of fatigue crack growth, residual strength, and fatigue lifetime for fiber composite laminates containing notches (holes). The failure model used for the analysis is based upon composite heterogeneous behavior and experimentally observed failure modes under both static and fatigue loading. The analysis is consistent with the wearout philosophy. Axial cracking and transverse cracking failure modes are treated together in the analysis. Cracking off-axis is handled by making a modification to the axial cracking analysis. The analysis predicts notched laminate failure from unidirectional material fatique properties using constant strain laminate analysis techniques. For multidirectional laminates, it is necessary to know lamina fatique behavior under axial normal stress, transverse normal stress and axial shear stress. Examples of the analysis method are given.

Mclaughlin, P. V., Jr.↗

NASA NTRS1975

Failure and fatigue mechanisms in composite materials

A phenomenological description of microfailure under monotonic and cyclic loading is presented, emphasizing the significance of material inhomogeneity for the analysis. Failure in unnotched unidirectional laminates is reviewed for the cases of tension, compression, shear, transverse normal, and combined loads. The failure of notched composite laminates is then studied, with particular attention paid to the effect of material heterogeneity on load concentration factors in circular holes in such laminates, and a 'materials engineering' shear-lay type model is presented. The fatigue of notched composites is discussed with the application of 'mechanistic wearout' model for determining crack propagation as a function of the number of fatigue cycles.-

Rosen, B. W.↗

NASA NTRS1974

A study of RSI under combined stresses

The behavior of typical rigidized surface insulation material (RSI) under combined loading states was investigated. In particular, the thermal stress states induced during reentry of the space shuttle were of prime concern. A typical RSI tile was analyzed for reentry thermal stresses under computed thermal gradients for a model of the RSI material. The results of the thermal stress analyses were then used to aid in defining typical combined stress states for the failure analysis of RSI.

Kibler, J. J.↗

NASA NTRS1974

Non-linear behavior of fiber composite laminates

The non-linear behavior of fiber composite laminates which results from lamina non-linear characteristics was examined. The analysis uses a Ramberg-Osgood representation of the lamina transverse and shear stress strain curves in conjunction with deformation theory to describe the resultant laminate non-linear behavior. A laminate having an arbitrary number of oriented layers and subjected to a general state of membrane stress was treated. Parametric results and comparison with experimental data and prior theoretical results are presented.

Hashin, Z.↗

NASA NTRS1974

Analytical study of rigidized fibrous materials

Insulation systems composed of micrometer-sized fibers bonded together with small amounts of binder have been developed for aerospace applications. The materials have a very high volid content and low density and can be characterized as a rigidized network of fibers randomly oriented in three-dimensional space. Analytical models suitable for the evaluation of the mechanical behavior of rigidized fibrous materials have been developed. The models treat the material as a space frame structure and includes the effects of joint fixity and fiber curvature. The geometrical and material property variabilities are represented by a number of trusses oriented in five planes. Each truss may have different material and geometric properties. Techniques have been developed to describe the continuous material property and geometry functions as a series of descrete quantities that can be used to describe each of the trusses in the model. Parametric studies were performed to show the influence of material variables on the mechanical behavior of the material. Results of calculations show good agreement with measured properties.

Rosen, B. W.↗

NASA NTRS1973

An investigation of the compressive strength of PRD-49-3/Epoxy composites

The development of unidirectional fiber composite materials is discussed. The mechanical and physical properties of the materials are described. Emphasis is placed in analyzing the compressive behavior of composite materials and developing methods for increasing compressive strength. The test program for evaluating the various procedures for improving compressive strength are reported.

Kulkarni, S. V.↗

NASA NTRS1972

Tensile failure criteria for fiber composite materials

The analysis provides insight into the failure mechanics of these materials and defines criteria which serve as tools for preliminary design material selection and for material reliability assessment. The model incorporates both dispersed and propagation type failures and includes the influence of material heterogeneity. The important effects of localized matrix damage and post-failure matrix shear stress transfer are included in the treatment. The model is used to evaluate the influence of key parameters on the failure of several commonly used fiber-matrix systems. Analyses of three possible failure modes were developed. These modes are the fiber break propagation mode, the cumulative group fracture mode, and the weakest link mode. Application of the new model to composite material systems has indicated several results which require attention in the development of reliable structural composites. Prominent among these are the size effect and the influence of fiber strength variability.

Rosen, B. W.↗

NASA NTRS1971

A concept for improving the dimensional stability of filamentary composites in one direction

Investigation of filamentary composites having high strength and stiffness and a zero thermal coefficient of expansion in one direction shows that advanced filament materials, such as boron, have substantial advantages over conventional filamentary composites. Various other results are discussed, including guidelines and analysis methods for further evaluation.

Dow, N. F.↗

NASA NTRS1970

Design and evaluation of three-phase fibrous composite structures

Study reveals composite combination evaluations for boron binder reinforcements for unidirectly reinforced boron/epoxy, glass binder reinforcements for unidirectionally reinforced boron/epoxy, and glass binder reinforcements for unidrectionally reinforced glass/epoxy.

Dow, N. F.↗

NASA NTRS1970

Testing filamentary composites

NOL ring split-dee tensile test has the advantages that the specimen is readily fabricated by winding and the test is performed in a conventional testing machine without special fixtures. Strain gages cannot be mounted, however, and substantial bending moments are introduced.

Dow, N. F.↗

NASA NTRS1970

Unidirectional composite stiffening

Simple structural elements are explored with configurations selected to best utilize composite materials. Combination of the biaxial properties of beryllium or an isotropic composite with the uniaxial properties of one directional filamentary reinforcement is studied.

Dow, N. F.↗