Search NASA⌕ Search

Engineering topics

Rossettos, J. N.

Publications and source records attributed to Rossettos, J. N..

9 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1997

Nondestructive Evaluation of Adhesively Bonded Joints

The final report consists of 5 published papers in referred journals and a technical letter to the technical monitor. These papers include the following: (1) Comparison of the effects of debonds and voids in adhesive; (2) On the peak shear stresses in adhesive joints with voids; (3) Nondestructive evaluation of adhesively bonded joints by acousto-ultrasonic technique and acoustic emission; (4) Multiaxial fatigue life evaluation of tubular adhesively bonded joints; (5) Theoretical and experimental evaluation of the bond strength under peeling loads. The letter outlines the progress of the research. Also included is preliminary information on the study of nondestructive evaluation of composite materials subjected to localized heat damage. The investigators studied the effects of localized heat on unidirectional fiber glass epoxy composite panels. Specimens of the fiber glass epoxy composites were subjected to 400 C heat for varying lengths of time. The specimens were subjected to nondestructive tests. The specimens were then pulled to their failure and acoustic emission of these specimens were measured. The analysis of the data was continuing as of the writing of the letter, and includes a finite element stress analysis of the problem.

Nayeb-Hashemi, Hamid↗
NASA NTRS1997

Comparison of the Effects of Debonds and Voids in Adhesive Joints

An analytical model is developed to compare the effects of voids an debonds on the interfacial shear stresses between the adherends and the adhesive in simple lap joints. Since the adhesive material above the debond may undergo some extension (either due to applied load or thermal expansion or both), a modified shear lag model, where the adhesive can take an extensional as well as shear deformation, is used in the analysis. The adherends take on only axial loads and act as membranes. Two coupled nondimensional differential equations are derived, and in general, five parameters govern the stress distribution in the overlap region. As expected, the major differences between the debond and the void occur for the stresses near the edge of the defect itself. Whether the defect is a debond or a void, is hardly discernible by the stresses at the overlap region. If the defect occurs precisely at or very close to either end of the overlap, however, differences of the order of 20 percent in the peak stresses can be obtained.

Rossettos, J. N.↗
NASA NTRS1997

Nondestructive Evaluation of Adhesively Bonded Joints by Acousto-Ultrasonic Technique and Acoustic Emission

Reliable applications of adhesively bonded joints require an effective nondestructive evaluation technique for their bond strength prediction. To properly evaluate factors affecting bond strength, effects of defects such as voids and disbonds on stress distribution in the overlap region must be understood. At the same time, in order to use acousto-ultrasonic (AU) technique to evaluate bond quality, the effect of these defects on dynamic response of single lap joints must be clear. The stress distribution in a single lap joint with and without defects (void or disbond) is analyzed. A bar-Theta parameter which contains adherend and adhesive thickness and properties is introduced. It is shown for bonded joints with bar-Theta greater than 10, that a symmetric void or disbond in the middle of overlap up to the 70 percent of overlap length has negligible effect on bond strength. In contrast frequency response analyses by a finite element technique showed that the dynamic response is affected significantly by the presence of voids or disbonds. These results have direct implication in the interpretations of AU results. Through transmission attenuation and a number of AU parameters for various specimens with and without defects are evaluated. It is found that although void and disbond have similar effects on bond strength (stress distribution), they have completely different effects on wave propagation characteristics. For steel-adhesive-steel specimens with voids, the attenuation changes are related to the bond strength. However, the attenuation changes for specimens with disbond are fairly constant over a disbond range. In order to incorporate the location of defects in AU parameters, a weighting function is introduced. Using an immersion system with focused transducers, a number of AU parameters are evaluated. It is found that by incorporating weighting functions in these parameters better sensitivities (AU parameters vs. bond strength) are achieved. Acoustic emission (AE) activities of steel-adhesive-steel specimens with bar-Theta equal to 3.4 are monitored. Two different formats of energy vs. time have resulted, each corresponding to the perfect specimens or the specimens with void or disbond. The relative acoustic energy and the number of events at failure are found to be a means for predicting the bond strength.

Nayeb-Hashemi, Hamid↗
NASA NTRS1974

Finite-element analysis of vibration and flutter of cantilever anisotropic plates

The hybrid stress finite element method is used to study the effects of filament angle and orthotropicity parameter on the vibration and flutter characteristics of cantilevered anisotropic plates. The results indicate a generally strong lack of monotonic dependence on filament angle. Also, the natural frequency in certain cases involving the first few modes, can become relatively insensitive to both filament angle and orthotropicity parameter for a range of filament angle beyond 70 deg. Values of critical dynamic pressure are obtained by a modal approach, in which the mode shapes are obtained by the hybrid stress method. Convergence of the modal method is rather rapid for the configurations analyzed, and a comparison of the method with an exact solution for the case of an isotropic simply supported plate shows that use of six modes gives excellent agreement.

Rossettos, J. N.↗
NASA NTRS1973

Modes and frequencies of transversely isotropic slightly curved Timoshenko beams.

An analysis of the vibration of transversely isotropic Timoshenko beams, which have small constant initial curvature, is presented, and a closed-form general solution to the governing equations is derived. Natural modes and frequencies are determined for both clamped and simply supported end conditions, and comparisons are made. The combined effects of initial curvature, transverse shear deformation, and boundary conditions are evaluated and discussed. Specifically, it is shown in what manner the clamped beam tends to be more sensitive to shear deformation than the simply supported beam, and how initial curvature reduces the difference. Calculations also show how, in cases where shear deformation becomes more important, the initial curvature has a correspondingly smaller influence on the results.

Rossettos, J. N.↗