Search NASA⌕ Search

Engineering topics

Rossi, Ruggero

Publications and source records attributed to Rossi, Ruggero.

7 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Impact of reactor architecture and design parameters on the performance of microbial electrolysis cells revealed by the electrode potential slope analysis

Microbial electrolysis cells (MECs) are appealing for recovering the chemical energy contained in domestic and industrial liquid wastes as hydrogen gas. Despite several years of research in the field, there is still a lack of critical analysis of how the reactor architecture dictates the electrochemical performance of the cell. In this study, internal resistance and onset voltage from the electrode potential slope analysis (EPS) were used in combination with current density, hydrogen production rate, reactor packing density, electrode spacing, membrane type and composition from 23 different studies to identify the reactor design parameters that primarily govern electrochemical performance of MECs. Using anion exchange membranes resulted in smaller internal resistances (AEM R int = 41± 40 mΩ m 2 ) and larger current density (18 ± 14 A m −2 ) compared to single chamber reactors (SC R int = 68 ± 58 mΩ m 2 ; 22 ± 16 A m −2 ) or MECs with cation exchange membranes (CEM R int = 376 ± 280 mΩ m 2 ; 3.0 ± 2.1 A m −2 ). Higher electrochemical performance for AEM- and SC-MECs translated in larger hydrogen gas production rates (0.122 mL H 2 C −1 for AEM vs 0.117 mL H 2 C −1 for SC), but only when inhibitors against hydrogen scavengers were added in single chamber systems (0.080 mL H 2 C −1 for SC without inhibitors). Following membrane type and composition, maintaining a small electrode spacing was the most critical parameter to improve MEC performance, indicating that the low conductivity of the media primarily limit performance by increasing ohmic resistance. Here, reactor volume and electrode surface area negatively correlated with internal resistance and current density, indicating that better performance of scaled-up reactors can likely be obtained by stacking multiple smaller units rather than just increasing reactor size. Although challenges remain in the implementation of MECs for hydrogen production from liquid wastes, advances in electrochemical engineering of the reactors can facilitate scale up and performance prediction at scale.

Electrochemistry↗
DOE OSTI2024

Hydrogen production in microbial electrolysis cells with biocathodes

Electroautotrophic microbes at biocathodes in microbial electrolysis cells (MECs) can catalyze the hydrogen evolution reaction with low energy demand, facilitating long-term stable performance through specific and renewable biocatalysts. However, MECs have not yet reached commercialization due to a lack of understanding of the optimal microbial strains and reactor configurations for achieving high performance. Here, we critically analyze the criteria for the inocula selection, with a focus on the effect of hydrogenase activity and microbe–electrode interactions. We also evaluate the impact of the reactor design and key parameters, such as membrane type, composition, and electrode surface area on internal resistance, mass transport, and pH imbalances within MECs. Furthermore, this analysis paves the way for advancements that could propel biocathode-assisted MECs toward scalable hydrogen gas production.

Biotechnology & Applied Microbiology↗
DOE OSTI2023

Increasing the Electrolyte Salinity to Improve the Performance of Anion Exchange Membrane Water Electrolyzers

Direct operation of anion exchange membrane water electrolyzers (AEMWEs) with near-neutral pH feeds avoids the use of highly alkaline and corrosive solutions. However, using neutral pH solutions currently faces fundamental operational challenges that diminish performance and reduce long-term stability due to poor solution conductivity and low hydroxide ion concentration. Here, we showed that amending near-neutral pH solutions with low concentrations of alkali metal salts in a dry-cathode configuration substantially improved performance and stability. Adding NaClO 4 (10 mM) to the anolyte reduced the operating voltage by 0.19 to 2.58 V at 500 mA/cm 2 compared to non-saline solutions (2.77 V). However, further increases in the feed salt concentration (100 mM NaClO 4 ) reduced performance (2.64 V) due to a greater co-ion diffusion through the anion exchange membrane. Electrolyzer performance was further improved by utilizing salts with high conductivity such as KNO 3 . Using a saline anolyte reduced ohmic resistance, resulting in smaller applied voltage and energy consumption for hydrogen generation, while the combined effect of the membrane charge and the electric field direction in the dry-cathode feed configuration minimized ion crossover. Thus, increasing the salinity of near-neutral pH solutions represents a cost-effective strategy to improve the performance of AEMWE compared to ultrapure electrolytes, minimizing risks and costs associated with recirculating highly alkaline solutions.

anion exchange membrane water electrolyzer↗
DOE OSTI2023

Using nickel-molybdenum cathode catalysts for efficient hydrogen gas production in microbial electrolysis cells

A low-cost cathode catalyst based on a NiMo alloy was examined here to replace noble metals for the hydrogen production in microbial electrolysis cells (MECs). Two NiMo catalysts were synthesized through either an electrochemical assisted (NiMo Elec) or a hydrothermal (NiMo Ht) approach. The NiMo Ht method enriched the electrocatalyst with Mo atoms compared to the NiMo Elec approach, producing a similar current density with a minimal overpotential of 50mV compared to Pt. Further, in MEC tests using the NiMo Ht catalyst, H 2 was generated at a highest rate of 81±3 L H2 /L-d (current density of 44.4 ± 0.9 A/m 2 ) at a cell voltage of -0.86 V, and a Coulombic efficiency of >97%. Modifying the closely stacked MEC design to include a reference electrode, and analysis of the electrode potentials using the electrode potential slope method, revealed a large contribution of the cathode resistance (5.3±0.5mΩm 2 ) compared to the anode (1.4±0.2mΩm 2 ) and ohmic resistance (0.83mΩm 2 ) for a total internal resistance of 7.6±0.5mΩm 2 . The high performance of the NiMo Ht catalyst coupled with its low cost provides an economically viable approach to advance the generation of biohydrogen in MECs.

25 ENERGY STORAGE↗
DOE OSTI2021

Vapor-Fed Cathode Microbial Electrolysis Cells with Closely Spaced Electrodes Enables Greatly Improved Performance

Hydrogen can be electrochemically produced in microbial electrolysis cells (MECs) by current generated from bacterial anodes with a small added voltage. MECs typically use a liquid catholyte containing a buffer or salts. However, anions in these catholytes result in charge being balanced predominantly by ions other than hydroxide or protons, leading to anode acidification. To enhance only hydroxide ion transport to the anode, we developed a novel vapor-fed MEC configuration lacking a catholyte with closely spaced electrodes and an anion exchange membrane to limit the acidification. This MEC design produced a record-high sustained current density of 43.1 ± 0.6 A/m 2 and a H 2 production rate of 72 ± 2 LH 2 /L-d (cell voltage of 0.79 ± 0.00 V). There was minimal impact on MEC performance of increased acetate concentrations, solution conductivity, or anolyte buffer capacity at applied voltages up to 1.1 V, as shown by a nearly constant internal resistance of only 6.8 ± 0.3 mΩ m 2 . At applied external voltages >1.1 V, the buffer capacity impacted performance, with current densities increasing from 28.5 ± 0.6 A/m 2 (20 mM phosphate buffer solution (PBS)) to 51 ± 1 A/m 2 (100 mM PBS). Furthermore, these results show that a vapor-fed MEC can produce higher and more stable performance than liquid-fed cathodes by enhancing transport of hydroxide ions to the anode.

anion exchange membrane↗