Search NASA⌕ Search

Engineering topics

Rossow, V. J.

Publications and source records attributed to Rossow, V. J..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Measurements in 80- by 120-foot wind tunnel of hazard posed by lift-generated wakes

The large, low speed wind tunnel at NASA-Ames has been used to study the characteristics of lift-generated vortices involved in the definition of aircraft-separation criteria, in order to enhance airport capacity without compromising safety. Attention is given to the potential hazard caused by the vortex wake of several configurations of a subsonic transport. Measured downwash distributions in the wake of three different wake-generator configurations are obtained by means of a vortex-lattice method, in order to predict the lift and rolling moment on several models of wake-following aircraft.

Rossow, V. J.↗
NASA NTRS1986

Improved Numerical Evaluation Method for Elliptic Integrals

Two modifications to Bartky's method for numerical evaluation of complete elliptic integrals increase rate of convergence and eliminate loss of accuracy due to roundoff errors. Other integrals (nonelliptic) evaluated by manipulating integrand into form F(R)/R required for evaluation by this method. Improved method used to map upper half of complex plane conformally onto interior or exterior of round-nosed wedges of various angles.

Rossow, V. J.↗
NASA NTRS1986

Aeorodynamic characteristics of an air-exchanger system for the 40- by 80-foot wind tunnel at Ames Research Center

A 1/50-scale model of the 40- by 80-Foot Wind Tunnel at Ames Research Center was used to study various air-exchange configurations. System components were tested throughout a range of parameters, and approximate analytical relationships were derived to explain the observed characteristics. It is found that the efficiency of the air exchanger could be increased (1) by adding a shaped wall to smoothly turn the incoming air downstream, (2) by changing to a contoured door at the inlet to control the flow rate, and (3) by increasing the size of the exhaust opening. The static pressures inside the circuit then remain within the design limits at the higher tunnel speeds if the air-exchange rate is about 5% or more. Since the model is much smaller than the full-scale facility, it is not possible to completely duplicate the tunnel, and it will be necessary to measure such characteristics as flow rate and tunnel pressures during implementation of the remodeled facility. The aerodynamic loads estimated for the inlet door and for nearby walls are also presented.

Rossow, V. J.↗
NASA NTRS1986

Experimental study of flow deflectors designed to alleviate ground winds induced by exhaust of 80-by 120-foot wind tunnel

An experimental study directed at finding a deflector ramp that will reduce to an acceptable level the ground winds under the exhaust jet of the 80 by 120 Foot Wind Tunnel at NASA Ames Center is described. A one-fifieth scale model of the full-scale facility was used to investigate how the jet flow field was modified by the various design parameters of the ramp. It was concluded that the ground winds were alleviated sufficiently by a ramp with end plates located next to the wind tunnel building along the ground edge of the exhaust opening. At full scale, the ramp should have a slant length of 7.62 m (25 ft) or more, and would be elevated at about 45 degrees to the ground plane. The material should have holes less than 15.2 (6 in) in diameter distributed uniformly over its surface to produce a porosity of about 30%.

Rossow, V. J.↗
NASA NTRS1986

Prospects for destructive self-induced interactions in a vortex pair due to sinusoidal disturbances

The vortex wakes of large transport aircraft can pose a hazard to smaller following aircraft in the vicinity of airports during landing and take-off operations if certain separation guidelines are not observed. In order to reduce the hazard potential, and thereby the separation distances, efforts are being made to find more rapid wake-dissipation mechanisms. In this paper numerical simulations are made of the three-dimensional time-dependent instabilities that might be initiated in a vortex pair by sinusoidal displacements of the filaments. The objective of the study was to find those displacements and phase angles that would produce the most rapid destruction of the vortices. It is concluded that, of the wave patterns tried on the one pair of wake filaments, the only instability mode that leads to destructive interactions of the vortices is the Scorer-Crow process.

Rossow, V. J.↗
NASA NTRS1985

Effect of ground and/or ceiling planes on thrust of rotors in hover

The thrust produced by a helicopter rotor hovering near ground and/or ceiling planes is investigated experimentally and theoretically. In the experiment, the thrust was measured on a 0.324-m-diam rotor operating between floor and ceiling planes which were located from 6 to 0.08 diam from the rotor disk. In the first theoretical model studied, the incompressible and inviscid flow induced by a sequence of vortex cylinders, located above and below the rotor to simulate the rotor wake and its interaction with the floor and ceiling planes, was considered. Comparison with experiment showed that this model overpredicts the change in thrust caused by the proximity of the walls. Therefore, a second arrangement of vortex cylinders was introduced which provides a more accurate prediction of the ground and ceiling effects on the thrust of the rotor in hover. The applicability of these results to a vented wind tunnel is also discussed.

Rossow, V. J.↗
NASA NTRS1985

Thrust changes induced by ground and ceiling planes on a rotor in hover

The thrust produced by a helicopter motor in hover has been studied by measuring the thrust on a model rotor 0.234 meters in diameter operating between ground and ceiling planes. The distance between the two planes and the rotor disk was in the range 0.08-6.0 rotor diameters. It was found that the confining surfaces changed the rotor thrust almost linearly with the logarithm of the distance from the confining surface. When both planes were near the rotor the variation was no longer linear. The measured thrust of the rotor was compared to predictions based on the theoretical calculations of Rossow (1985), and the results are given in a table.

Rossow, V. J.↗
NASA NTRS1985

On Bartky's method for evaluation of integrals of elliptic type with application to round-nosed wedges

Bartky's method for the numerical evluation of integrals of the complete elliptic type is modified to improve its accuracy. The resulting modified method is then applied to integrals involving complex arithmetic which map the upper half of one plane onto either the interior or exterior of round-nosed wedges. These solutions have engineering applications to such problems as the design of magnets and the flow of fluids in and around corners.

Rossow, V. J.↗
NASA NTRS1985

On the wake hazard alleviation associated with roll oscillations of wake-generating aircraft

An explanation is provided for the difference in wake vortex alleviation achieved by roll oscillations in flight tests with B-747 and L-1011 transport aircraft. Both aircraft had their landing flaps extended and several spoilers deployed. Numerical analysis shows that the growth in amplitude of the initial waves in the vortex filament is brought about by the sinusoidal instability. In the case of the B-747, growth is enhanced by a vortex whose strength is about the same as the tip vortex which is shed near the fuselage by the inboard end of the flaps. Conversely, the L-1011 is estimated to shed a negligible fuselage vortex and to have a relatively strong wingtip vortex. These characteristics bring about a rotation and amplification of the initial waves in the vortex filaments in the wake of the B-747 but not in the L-1011 vortex wake. An aircraft following the B-747 would then experience only intermittent encounters with the intense parts of the wake vortices so that the time-averaged wake-induced rolling moment is substantially reduced.

Rossow, V. J.↗
NASA NTRS1978

Experimental investigation of wing fin configurations for alleviation of vortex wakes of aircraft

A variety of fin configurations were tested on a model of the Boeing B747 in 40 by 80 foot wind tunnels. The test results confirmed that a reduction in wake rolling moment was brought about by the vortex shed by the fins so that a wide range of designs can be used to achieve wake alleviation. It was also found that the reduction in wake-induced rolling moments was especially sensitive to the location of the smaller fins on the wing and that the penalties in lift and drag can probably be made negligible by proper fin design.

Rossow, V. J.↗
NASA NTRS1977

Effect of wing fins on lift-generated wakes

A theoretical and experimental study has been made of the effect of wing-mounted fins on the vortex wakes of subsonic aircraft. The theory is used (a) to gain an understanding of wake alleviation by vortex injection and (b) to guide the experimental investigation. Wind-tunnel tests were used to evaluate the alleviation achievable and to find the optimum values for the various fin parameters. It was found that vertical fins mounted on the upper surface of a wing could lower the wake-induced rolling moments on an encountering wing by a factor of 3 or more. The most promising fin configuration found for the Boeing 747 model is a fin positioned 48% outboard from the centerline to the wingtip with a height of 0.014 span, a chord of 0.085 span, and an 18 deg angle of attack. This fin configuration caused a 10% increase in drag but no lift penalty.

Rossow, V. J.↗
NASA NTRS1977

Lift enhancement by an externally trapped vortex

A theoretical study is made of the performance capabilities of a lift concept that utilizes a spanwise vortex over the upper surface of the wing. The vortex is generated by a vertical flap near the leading edge of the wing and maintained by suction through orifices in endplates at the wingtip. The analysis approximates the three-dimensional flow field with a two-dimensional configuration that is mapped by conformal transformation into the flow about a circle. Theoretical solutions for a range of flap and orifice configurations predict that section lift coefficients up to around 10 can be achieved. It is concluded that such a lift concept is applicable to STOL aircraft if the vortex can be adequately stabilized and if the endplate suction can be generated efficiently.

Rossow, V. J.↗
NASA NTRS1977

Inviscid modeling of aircraft trailing vortices

A survey is presented of inviscid theoretical methods that are useful in the study of lift-generated vortices. Concepts derived using these invisicid theories are cited which have helped to guide research directed at alleviating the velocities and rolling moments imposed on aircraft entering these wakes.

Rossow, V. J.↗
NASA NTRS1976

Convective merging of vortex cores in lift-generated wakes

The several wake vortices which originate from aircraft wingtips, flap edges, engine pylons, etc. usually merge, in the far field, to form a single pair whose structure determines the hazard posed to encountering aircraft. To gain an understanding of the process whereby vortices merge and disperse, a numerical study was made of the interaction of two-dimensional, time-dependent, inviscid vortical regions. It was found that discrete boundaries, which depend on the structure and spacing of the vortices, distinguish merging from nonmerging situations. Furthermore, certain arrays of finite vortex cores that alternate in sign were found to undergo division and merging that may be useful in alleviating the hazard posed by aircraft wakes.

Rossow, V. J.↗
NASA NTRS1976

Wind-Tunnel Investigation of the Effect of Porous Spoilers on the Wake of a Subsonic Transport Model

Tests were conducted in the Ames Research Center 40- by 80-Foot Wind Tunnel to determine how porosity of wing spoilers on a B-747 airplane would affect the rolling moments imposed on an aircraft following in the wake. It was found that spoilers with 40 percent porosity and hole diameter to thickness ratio of 1.1 were just as effective in reducing the rolling moment imposed on the follower as solid spoilers, for the case of two spoilers per wing panel (6.4 percent semispan each) with a following model whose span was 20 percent of the span of the generator. When a larger following model was tested, whose span was 50 percent of that of the generator, the effectiveness of the two spoilers per wing was substantially reduced.

Corsiglia, V. R.↗
NASA NTRS1975

Experimental study of the effect of span loading on aircraft wakes

Measurements were made in the NASA-Ames 40- by 80-Foot Wind Tunnel of the rolling moment induced on a following model in the wake 13.6 spans behind a subsonic transport model for a variety of trailing edge flap settings of the generator. It was found that the rolling moment on the following model was reduced substantially, compared to the conventional landing configuration, by reshaping the span loading on the generating model to approximate a span loading, found in earlier studies, which resulted in reduced wake velocities. This was accomplished by retracting the outboard trailing edge flaps. It was concluded, based on flow visualization conducted in the wind tunnel as well as in a water tow facility, that this flap arrangement redistributes the vorticity shed by the wing along the span to form three vortex pairs that interact to disperse the wake.

Corsiglia, V. R.↗
NASA NTRS1975

Experimental study of the effect on span loading on aircraft wakes

Measurements were made in the NASA-Ames 40- by 80-foot wind tunnel of the rolling moment induced on a following model in the wake 13.6 spans behind a subsonic transport model for a variety of trailing edge flap settings of the generator. It was found that the rolling moment on the following model was reduced substantially, compared to the conventional landing configuration, by reshaping the span loading on the generating model to approximate a span loading, found in earlier studies, which resulted in reduced wake velocities. This was accomplished by retracting the outboard trailing edge flaps. It was concluded, based on flow visualization conducted in the wind tunnel as well as in a water tow facility, that this flap arrangement redistributes the vorticity shed by the wing along the span to form three vortex pairs that interact to disperse the wake.

Corsiglia, V. R.↗