Engineering topics

Rotem, A.

Publications and source records attributed to Rotem, A..

10 records

NASA NTRS1991

The fatigue behaviour of orthotropic laminates under tension-compression loading

The fatigue behavior of orthotropic laminates (0, +/-45, 0 deg)2s and (90, +/-45, 90 deg)2s, has been evaluated under alternating tension-compression loading. Even though the first laminate is much stronger than the second, both started to fail by delamination. Visual damage started to show only at the very end of the fatigue life but measurement of the stiffness showed that degradation starts at about 80 percent of the fatigue life. The first laminate failed in compression after delamination between the 0 and the 45 deg laminae, while the second failed in tension after delamination between the +45 and -45 deg laminae. It is shown that the interlaminar fatigue strength of both laminate structures can be correlated to the applied fatigue load.

Rotem, A.↗

NASA NTRS1991

The fatigue behavior of composite laminates under various mean stresses

A method is developed for predicting the S-N curve of a composite laminate which is subjected to an arbitrary stress ratio, R (minimum stress/maximum stress). The method is based on the measuring of the S-N behavior of two distinct cases, tension-tension and compression-compression fatigue loadings. Using these parameters, expressions are formulated that estimate the fatigue behavior under any stress ratio loading. Experimental results from the testing of graphite/epoxy laminates, with various structures, are compared with the predictions and show good agreement.

Rotem, A.↗

NASA NTRS1989

Failure of a laminated composite under tension-compression fatigue loading

The fatigue behavior of composite laminates under tension-compression loading is analyzed and compared with behavior under tension-tension and compression-compression loading. It is shown that for meaningful fatigue conditions, the tension-compression case is the dominant one. Both tension and compression failure modes can occur under the reversed loading, and failure is dependent on the specific lay-up of the laminate and the difference between the tensile static strength and the absolute value of the compressive static strength. The use of a fatigue failure envelope for determining the fatigue life and mode of failure is proposed and demonstrated.

Rotem, A.↗

NASA NTRS1989

The durability of graphite/epoxy laminate subjected to repeated low velocity impact

Low velocity impact has been considered as quasi-static loading, as the dynamic effects are decaying before the pressure reaches its maximum. However, when the impact energy is low enough as not to cause visible damage, the dynamic effect at the beginning of the impact may cause internal damage to the laminate. Laminates were loaded quasi-statically and by impact to the same bending strain and with the same indenter shape several times. The laminates that were subjected to the impact loading failed much more rapidly. Analysis of the problem shows that the stress waves created by the impact at the beginning of contact intensify the damage zone created by the preceding impact until the final failure occurs.

Rotem, A.↗

NASA NTRS1982

Accelerated fatigue durability of a high performance composite

The fatigue behavior of multidirectional graphite-epoxy laminates was analyzed theoretically and experimentally in an effort to establish an accelerated testing methodology. Analysis of the failure mechanism in fatigue of the laminates led to the determination of the failure mode governing fracture. The nonlinear, cyclic-dependent shear modulus was used to calculate the changing stress field in the laminate during the fatigue loading. Fatigue tests were performed at three different temperatures: 25 C, 74 C, and 114 C. The prediction of the S-N curves was made based on the artificial static strength artificial static strength at a reference temperature and the fatigue functions associated with them. The prediction of an S-N curve at other temperatures was performed using shifting factors determined for the specific failure mode. For multidirectional laminates, different S-N curves at different temperatures could be predicted using these shifting factors. Different S-N curves at different temperatures occur only when the fatigue failure mode is matrix dominated. It was found that whenever the fatigue failure mode is fiber dominated, temperature, over the range investigated, had no influence on the fatigue life. These results permit the prediction of long-time, low temperature fatigue behavior from data obtained in short time, high temperature testing, for laminates governed by a matrix failure mode.

Rotem, A.↗

NASA NTRS1981

Fatigue behavior of graphite-epoxy laminates at elevated temperatures

An examination and analysis is presented of the elevated temperature fatigue behavior of multidirectional graphite-epoxy laminates in terms of single lamina behavior. The laminate strength is predicted by considering the cyclic stress field in each lamina, the interlaminar stresses, and the experimentally determined temperature-effect 'shifting factors'. The initial failure of a lamina in a laminate is examined first in terms of stress redistribution, and then in terms of total failure and final laminate fracture; these analytical results are then compared with the actual fatigue behavior of T300/5208 graphite-epoxy composite laminates. In view of the agreement obtained, it is concluded that the temperature 'shifting factors' introduced here enable one to predict long-term behavior at a given temperature from short-time testing at elevated temperatures.

Rotem, A.↗

NASA NTRS1979

Fracture modes and acoustic emission of composite materials

Unidirectional fibrous composite material laminae are the construction material of a laminate. Four failure modes can occur in this material, and the identification of these modes is as important as the identification of onset of fracture. Acoustic emission (AE) pulses, generated by the change in the stress field resulting from cracking in a material, have a unique pattern of amplitude distribution that depends only on the mode of fracture and the type of material. By using a tapered double-cantilever beam as grips for the unidirectional lamina, a crack with a constant stress intensity factor was induced, thus eliminating the factor of the stress level. Placing the lamina in different directions relative to the grips imposed a different failure mode. By plotting the log of the relative number of AE pulses above some level versus the log of the relative level, a single constant coefficient can be measured for each material and mode of fracture. The AE energy is proportional to the energy released by the cracking; this proportionality depends on the medium where the AE waves have to travel, and not on the cracking mode.

Rotem, A.↗

NASA NTRS1979

A temperature dependent fatigue failure criterion for graphite/epoxy laminates

A fatigue failure criterion applicable to composite materials is developed and applied to predict the fatigue behavior of graphite/epoxy laminates with particular emphasis on the influence of temperature. Tensile stress-strain curves and tension-tension fatigue curves for various unidirectional, angle-ply and symmetrically balanced laminates were developed at test temperatures of 25 C, 74 C and 114 C. In general for most laminates a reduction in both static strength and fatigue strength is observed with increasing temperature. This reduction appeared more severe in fatigue loading than in static tensile loading and most severe where the shear stress in the lamina is the dominant failure mode. Through an analytical formulation of shifting functions for the influences of temperature, all fatigue data are shown to be capable of being reduced to a single reference curve at some temperature. Additionally, examples are given which demonstrate the capability of the fatigue failure criterion to predict failure of complex symmetrically balanced laminates from relevant parameters obtained from the observed behavior of unidirectional and angle-ply laminates.

Rotem, A.↗

NASA NTRS1978

A temperature dependent fatigue failure criterion for graphite/epoxy laminates

A fatigue failure criterion applicable to composite materials is developed and applied to predict the fatigue behavior of graphite/epoxy laminates with particular emphasis on the influence of temperature. Tensile stress-strain curves and tension-tension fatigue curves for various unidirectional, angle-ply and symmetrically balanced laminates were developed at test temperatures of 25 C, 74 C, and 114 C. For most laminates a reduction in both static strength and fatigue strength is observed with increasing temperature. This reduction appeared more severe in fatigue loading than in static tensile loading and most severe where the shear stress in the lamina is the dominate failure mode. Through an analytical formulation of shifting functions for the influences of temperature, all fatigue data are shown to be capable of being reduced to a single reference curve at some temperature. Examples are given which demonstrate the capability of the fatigue failure criterion to predict failure of complex symmetrically balanced laminates from relevant parameters obtained from the observed behavior of unidirectional and angle-ply laminates.

Rotem, A.↗

NASA NTRS1978

The estimation of residual strength of composites by acoustic emission

The strength of unidirectional fibrous composite materials was measured as a function of the acoustic emission. Specimens of glass fibers and carbon fibers in an epoxy matrix were tested to fracture. Many of the specimens were with existing defects. It was shown, analytically and experimentally, that defective material starts to emit acoustic waves at a much lower stress level than nondefective material. It was found that for glass fiber material, the ultimate strength of the composite is proportional to the stress level for which a specific number of acoustic emission counts was reached. For carbon fiber material, this phenomenon is less pronounced.

Rotem, A.↗