Search NASA⌕ Search

Engineering topics

Rothamer, David

Publications and source records attributed to Rothamer, David.

14 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Improving Efficiency of Off-Road Vehicles by Novel Integration of Electric Machines and Advanced Combustion Engines

Modern off-road equipment will increasingly rely on electrified implements that will deliver precision control with a smaller footprint than hydraulics. The primary energy converter, however, will be an onboard reciprocating internal combustion engine because of the power density of hydrocarbon fuels in comparison to electrical energy storage and the remote locations where much of this equipment is deployed. Adding energy storage and electric machines creates opportunities to improve efficiency while reducing emissions. This program investigated approaches to take advantage of the extra flexibility that an enhanced electrical system to enable high-efficiency, low-emissions combustion technologies. The current program evaluated hybridization of both the torque application and air-handling systems to maximize efficiency while minimizing cost. This program designed, analyzed and tested a hybrid off-road vehicle consisting of a series electric powertrain with energy storage, an electrified air system, and a 33% downsized diesel engine. Detailed comparisons were made between the base powertrain and the developed powertrain using powertrain simulations, engine testing, and vehicle testing. The key results of the study are: • The resulting vehicle reduces fuel consumption by 5% to 15% at equal productivity. The primary improvements were due to recovery of regenerative braking losses for cycles where large transients are encountered. • The electrified air system was an enabler to allow engine downsizing. This was most important for duty-cycles where the engine primarily operated at moderate loads and had few low speed high torque conditions. • Engine level improvements showed re-optimization of the powertrain is possible when electrified air handing is available. Increased exhaust gas recirculation and advanced injection timing allowed up to a 15% reduction in brake specific fuel consumption at equal NOx and transient response. Compared to the larger engine, the downsized engine achieves up to an 18% reduction in brake specific fuel consumption over the non-road transient cycle. • The life cycle analysis and total cost of ownership study showed that the hybrid powertrain has the potential to reduce 5-year CO2 and total cost of ownership by ~6% over the baseline vehicle. The results also indicated that a pure battery electric vehicle is not feasible in this application and is likely to increase the CO2 emissions due to the CO2 from battery production. A hybrid powertrain with low carbon fuels shows the potential to substantially reduce CO2 and total cost of ownership.

02 PETROLEUM↗
DOE OSTI2024

Scale-Up Studies for the Dehydration of C 4+ Alcohols into Drop-In Diesel Fuel

Herein, we demonstrate the production of liter quantities of drop-in diesel-range ethers from biomass-derived alcohols. We report scale-up resultsfor the dehydration of a mixture of C 4+ alcohols using powder and pellet zeolite Ycatalyst in continuous flow and batch reactors. The activity of zeolite Y decreaseswith the introduction of an alumina binder. Large alcohols, as well as branchedand secondary alcohols, increase the coke content over the pellet Y catalyst. Thepellet formulation had lower carbon balances and selectivity to C 10+ ethers,suggesting that the pellet formulation increases alcohol absorption and cokeproduction. Crushing the pellet Y catalyst to smaller particle sizes does notrecover the activity of zeolite Y in its powder form. Cold flow experiments showthat particle agglomeration contributes to pressure buildup in the continuous flowreactor. C 10+ ether blends can be produced in batch reactors at high alcohol conversion regimes. One liter of a diesel #2 blend wasproduced by scaling up this reaction. The final blend consists of a substantial portion of C 10+ ethers (63.7 wt %), followed by heavyunknown products (27.4 wt %). Furthermore, the final alcohol and butyl ether concentration values were 7.3 and 1.5 wt %, respectively. Theblendstock reported in this paper can satisfy diesel #2 ASTM standards for density, cloud point, flashpoint, and cetane number.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Production of drop-in biodiesel blendstocks via competitive acid-catalyzed dehydration reactions using ethanol oligomerization products

Ethanol can be converted into diesel fuel ethers using a three-step catalytic approach that involves ethanol oligomerization to larger alcohols, hydrogenolysis of the esters followed by dehydration of the C4 to C8 alcohols into ethers. In this paper we report results for the dehydration of a mixture of C4 – C8 alcohols using a zeolite Y catalyst in a continuous flow reactor. Mono-molecular dehydration of the alcohols produces olefins while bi-molecular dehydration of the alcohol produces ethers. Increasing the pressure increases the ether selectivity while decreasing the pressure produces more olefins. Linear alcohol feeds produce more C8+ ethers, while branched and secondary alcohols lead to more olefins. Olefin and coke selectivities increase with increasing carbon chain length of alcohols. Secondary alcohols lead to higher coke selectivities. Furthermore, ethanol/Butanol oligomerization experiments showed that the incoming dehydration feedstock can be grown to larger C6+ alcohol fractions, leading to higher yields of C10+ diesel-range ethers.

09 BIOMASS FUELS↗
DOE OSTI2023

Catalytic upgrading of ethanol to C8+ distillate range ethers via Guerbet coupling and etherification

In this presentation we describe the catalytic approaches for conversion of ethanol into diesel fuel ethers. This involves first alcohol oligomerization, followed by acid-catalyzed dehydration. As we will show in this presentation, ethanol can be converted to higher linear and α-branched alcohols by C-C coupling reactions (ethanol oligomerization) as well as to high molecular weight esters by C-O coupling reactions with Cu/MgxAlOy (CuHT) catalysts. Alcohols may be converted to ethers via bimolecular dehydration in a subsequent step. We have identified more than 160 number of species in the products including alcohols, esters, aldehydes, ketones, and olefins. Alcohols range from C4 to C10. Both alcohols and esters follow a Schulz-Flory chain growth model. We show the relationship between the catalyst properties (BET surface area, acid and base site count and Cu loading and synthesis method) and the performance in the reactions. We also show that physical mixtures of CuHT and HT can have similar product selectivity of low loading CuHT catalysts. The selectivity towards diesel fuel precursor compounds (hereafter ‘DFPC’) increased with conversion until reaching a plateau at high ethanol conversion (~70%). Alcohol selectivity follows a Schultz-Flory distribution at all studied conversions, and that adsorbed ethanol-derived species may undergo surface oligomerization into 1-butanol and higher alcohols before desorbing in a chain-growth mechanism. Zeolite catalysts convert the C4+ alcohols into C8+ ethers in both batch and continuous flow reactors. Selectivities of up to 80% to C8+ ethers at around 70% conversion using a single pass continuous flow system are achieved. The final product feedstocks obtained from etherification have been used in technoeconomic (TEA) and lifecycle analysis (LCA), which indicate a reduction in greenhouse gas (GHG) emissions of 50% relative to conventional diesel and diesel fuel prices that are lower than biodiesel. These final feedstocks are undergoing engine testing to elucidate the physiochemical properties and compare well to diesel #2 ASTM standards.

Huber, George↗
DOE OSTI2023

Knock-limited combustion of ethanol-, isobutanol-, and 2-methyl-3-buten-2-ol-gasoline blends in a direct-injected spark-ignition engine

Knock-limited combustion of alcohol-gasoline fuel blends was studied in a direct-injection spark-ignition engine. Ethanol, isobutanol (2-methyl-1-propanol), and methylbutenol (2-methyl-3-buten-2-ol) were splash-blended with a blendstock for oxygenate blending (BOB) gasoline. Ethanol was blended in fractions of 10%, 20%, and 30% by volume (E10, E20, and E30). Isobutanol and methylbutenol were blended to match the oxygen weight percentage of the ethanol blends, resulting in blends of 16%, 32%, and 49% (I16, I32, and I49) isobutanol by volume and 18%, 37%, and 56% (M18, M37, and M56) methylbutenol by volume. Neat BOB and gasoline primary reference fuels (PRF) with octane numbers (ON) of 87 (PRF87) and 100 (PRF100) were included for reference. The engine was operated at fixed speed, equivalence ratio, and injection timing while knock-limited spark advance was located across a range of intake pressures. Low-level alcohol blends E10 and M18 had similar knocking behavior and appeared to be slightly more knock-resistant than I16. For mid-level blends, E20 showed further improvement over I32 while M37 showed noticeably better knock resistance, able to match the knock-resistance of PRF100 for loads above 1000 kPa gross indicated mean effective pressure (GIMEP). For high-level blends, the difference between E30 and I49 was similar to their mid-level counterparts. However, M56 showed significant improvement over E30 and I49 throughout the entire range of loads tested. M56 exceeded the knock-resistance of PRF100 for loads above 700 kPa GIMEP. The improved knock-resistance combined with the increased volumetric energy density of methylbutenol resulted in improved fuel consumption and indicated efficiency. The overall results of this study indicate that the order of knock-resistance of these three alcohols, for direct-injection operation with injection during the intake stroke, is isobutanol < ethanol < methylbutenol when compared on an equal oxygen weight basis.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2023

Production of bio-diesel blend stocks via acid-catalyzed dehydration of ethanol oligomerization products

Ethanol is the most widely produced biofuel in the world. Gasoline demand is projected to decrease in the next 20 years largely due to an increase in electric vehicles. Diesel fuel demand is projected to continue to increase. Long-chain mono C10+ ethers have high cetane numbers and appropriate physical properties to be blended at high levels into petroleum diesel fuel. A techno-economic analysis shows that the ethers can be produced at prices similar to biodiesel. In our presentation we will show the catalytic chemistry involved in our ethanol to diesel approach, the engine and physical measurements of the produced diesel-range ethers, and a summary of the techno-economic analysis.

Canales, Emmanuel↗
DOE OSTI2023

Exploration of Fuel Property Impacts on the Combustion of Late Post Injections Using Binary Blends and High-Reactivity Ether Bioblendstocks

In this study, the impacts of fuel volatility and reactivity on combustion stability and emissions were studied in a light-duty single-cylinder research engine for a three-injection catalyst heating operation strategy with late post-injections. Here, N-heptane and blends of farnesane/2,2,4,4,6,8,8-heptamethylnonane were used to study the impacts of volatility and reactivity. The effect of increased chemical reactivity was also analysed by comparing the baseline #2 diesel operation with a pure blend of mono-ether components (CN > 100) representative of potential high cetane oxygenated bioblendstocks and a 25 vol.% blend of the mono-ether blend and #2 diesel with a cetane number (CN) of 55. At constant reactivity, little to no variation in combustion performance was observed due to differences in volatility, whereas increased reactivity improved combustion stability and efficiency at late injection timings. Fuels with higher reactivity were found to reduce engine-out hydrocarbon and carbon monoxide emissions while also achieving stable combustion at post-injection timings later than those achievable with #2 diesel fuel. The pure ether blend had the latest achievable post-injection timing of +30.5 CAD while still maintaining stable combustion (coefficient of variation of gross-indicated mean effective pressure < 5%). With post-injection timing adjusted to achieve a matched exhaust temperature of 300 °C, the ether-diesel CN 55 blend was observed to have slightly higher thermal efficiency in comparison to the baseline #2 diesel fuel. The results also indicate that cetane number may serve as a good indicator of combustion characteristics at late injection timings used for aftertreatment thermal management operation.

09 BIOMASS FUELS↗
DOE OSTI2022

A System Level Analysis of Ethanol Upgrading to Middle Distillates

We systematically study the upgrading of ethanol toward middle distillates with desired properties. To survey the large design space, we introduce a novel superstructure-based optimization framework integrating process design and fuel formulation. We show that biorefineries that produce middle distillates by upgrading lignocellulosic ethanol can have an energy return on investment (EROI) greater than 1. Additionally, we show that technological improvements can lead to significant increases in EROI. Furthermore, trade-offs between fuel properties and biorefinery profitability are established, showing how process economics are strongly influenced by fuel properties. In the case of diesel, the feasibility of producing high cetane number biofuels is demonstrated, coupled with a discussion of the technological requirements and costs to produce these superior fuels. It is also shown that the minimum fuel selling price (MFSP) can be reduced by increasing the biorefinery complexity. Lastly, we discuss the possibility of satisfying current and projected middle distillates demand in the U.S. using biofuels produced by ethanol upgrading, and we estimate the potential CO2 mitigation of these technologies.

09 BIOMASS FUELS↗
DOE OSTI2022

Catalytic Upgrading of Ethanol to C8+ Distillate Range Ethers via Guerbet Coupling and Etherification

Guerbet coupling followed by etherification is a two step process for conversion of ethanol into distillate range molecules. This involves first alcohol oligomerization, followed by acid-catalyzed dehydration. As we will show in this presentation, ethanol can be converted to higher linear and α-branched alcohols by C-C coupling reactions (ethanol oligomerization) as well as to high molecular weight esters by C-O coupling reactions with Cu/MgxAlOy (CuHT) catalysts. Alcohols may be converted to ethers via bimolecular dehydration in a subsequent step. We have identified more than 160 number of species in the products including alcohols, esters, aldehydes, ketonces, and olefins. Alcohols range from C4 to C10. Both alcohols and esters follow a Schulz-Flory chain growth model. We show the relationship between the catalyst properties (BET surface area, acid and base site count and Cu loading and synthesis method) and the performance in the reactions. We also show that physical mixtures of CuHT and HT can have similar product selectivity of low loading CuHT catalysts. The selectivity towards diesel fuel precursor compounds (hereafter ‘DFPC’) increased with conversion until reaching a plateau at high ethanol conversion (~70%). Alcohol selectivity follows a Schultz-Flory distribution at all studied conversions, and that adsorbed ethanol-derived species may undergo surface oligomerization into 1-butanol and higher alcohols before desorbing in a chain-growth mechanism. Zeolite catalysts convert the C4+ alcohols into C8+ ethers in both batch and continuous flow reactors. Selectivities of up to 80% to C8+ ethers at around 70% conversion using a single pass continuous flow system are able to be achieved. The final product feedstocks obtained from etherification have been used in technoeconomic (TEA) and lifecycle analysis (LCA), which indicate a reduction in greenhouse gas (GHG) emissions of 50% relative to conventional diesel. These final feedstocks are undergoing engine testing to elucidate the physiochemical properties and will be compared to diesel #2 ASTM standards as a reference and will serve as a basis to improve the final bio-diesel blendstocks from etherification.

Huber, George↗
DOE OSTI2022

Simple Autoignition Model for the Derived Cetane Number of Oxygenated Compounds and Fuel Blends

A simple four-step autoignition model was used to derive an expression for the ignition delay and derived cetane number (DCN) measured by ignition quality testers (IQT) for oxygenated compounds and blends as a function of each compound’s global initiation and net chain branching rate constants. Expressions for these values were determined assuming they could be related to the functional groups present in a given compound. Measurements for 124 compounds and 94 binary and ternary blends, gathered from the literature and performed at UW-Madison, were used to obtain the explicit dependence of the measured ignition delay on each functional group. The new model was able to successfully describe the ignition behavior of both the compounds and blends, with an average DCN error of 5.0 (22%) and 3.5 (15%), respectively. Additionally, the blend model could naturally be modified into a mixing rule by incorporating existing IQT ignition delay data for each compound. Use of the mixing rule was found to offer improvements over the full prediction, with an average DCN error of 3.2 (14%).

09 BIOMASS FUELS↗
DOE OSTI2022

Simple Autoignition Model for the Derived Cetane Number of Oxygenated Compounds and Fuel Blends

A four-step autoignition model was used to derive an expression for the ignition delay and derived cetane number (DCN) measured by ignition quality testers (IQT) for oxygenated compounds and blends as a function of each compound’s global initiation and net chain branching rate constants. Expressions for these values were determined assuming they could be related to the functional groups present in a compound. Measurements for 124 compounds and 94 binary and ternary blends, gathered from the literature and performed at UW-Madison, were used to obtain the dependence of the measured ignition delay on each functional group. The new model was able to describe the ignition behavior of both the compounds and blends, with an average DCN error of 5.0 (22%) and 3.5 (15%), respectively. Additionally, the blend model was transformed into a mixing rule by incorporating existing IQT ignition delay data for each compound. Use of the mixing rule was found to offer improvements over the full prediction, with an average DCN error of 3.2 (14%).

Witkowski, Dustin↗
DOE OSTI2021

Experimental investigation of the effect of pore size distribution on nano-particle capture efficiency within ceramic particulate filters

The effect of the pore size distribution on size-resolved filtration efficiency was investigated for two ceramic particulate filters using particulate matter (PM) generated by a spark-ignition direct-injection engine fueled with gasoline. The cordierite filter tested had a porosity of 43%, a median pore diameter (d_50) of 12 µm, and a wide pore size distribution with a lognormal standard deviation (s’) of 0.3. The aluminum titanate filter had very similar porosity, d_50, and thickness, but significantly narrower pore size distribution (s’ = 0.1). The testing of two filters under identical experimental conditions enabled the impact of the pore size distribution on filtration performance to be evaluated. Filtration experiments were performed focusing on just the filter wall, starting from a clean filter until the transition to cake filtration (filtration efficiency > 99%). Time-resolved particle size distribution measurements were used to evaluate the progression of filtration performance and estimate trapped mass within the filter. The aluminum titanate filter, with a narrow pore size distribution, exhibited significantly better diffusion capture efficiency. The negative impact of higher flow velocity on diffusion capture efficiency was more pronounced for a narrower pore size distribution. Flow distributions measured using capillary-flow porometry were used to develop a cylindrical pore flow model to understand the impact of the differences in pore size distribution on observed trends in diffusion capture efficiency within a clean filter. The model helps demonstrate how large pores on the high end of a wider pore size distribution can carry a large fraction of the flow, with less efficient capture of small particles by diffusion. The experimental results and data demonstrate that the bubble point diameter and width of the pore size distribution significantly influence diffusion capture efficiencies for filters with very similar median pore diameter, porosity, and thickness.

aerosol filtration, Aftertreatment, ceramic exhaus↗
DOE OSTI2020

Optical Investigation of Catalyst Heating Operation in a Light-Duty Compression-Ignition Engine

It is well known that cold start engine operation contributes a majority of tail-pipe emissions during a vehicle drive cycle. Aftertreatment catalysts have poor conversion efficiency during this period due to low conversion efficiency at temperatures less than their light-off temperature. A late post injection strategy, with a delayed injection to increase exhaust enthalpy, can help decrease the time required to heat-up the catalyst. However, late injections into conditions with decreasing temperature and density can result in high emissions and combustion instability. In this study a three-injection strategy with a late-post injection was investigated in an optically-accessible engine. For the first two injections (pilot and main) timing and duration were held constant as the post injection timing was swept and duration varied to hold load constant, at a relevant light-load catalyst heating operating condition. Simultaneous double-pass schlieren and OH chemiluminescence data were acquired in an optically-accessible 0.4 L single-cylinder engine to understand spray characteristics and combustion behavior for #2 diesel fuel. Optical images analysis revealed higher liquid penetration and lower vaporization of the liquid fuel jet as post injection is retarded. It is also observed that retarding post injection timing to +25 CAD resulted in lower observed soot concentration in the piston bowl.

99 GENERAL AND MISCELLANEOUS↗