Search NASA⌕ Search

Engineering topics

Roycroft, Rebecca Amelia

Publications and source records attributed to Roycroft, Rebecca Amelia.

5 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Post-Shot Report for OMEGA Double Cylinders (CylDRT 22B)

The direct-drive double cylinder experimental platform is a high-energy-density (HED) science platform designed to image an imploding cylindrical target. The target consists of a directly-driven outer cylinder and a shock-and-collision driven inner cylinder. The purpose of this platform is to study hydrodynamic instability growth on the inner cylinder, the outer surface of which is classically Rayleigh-Taylor unstable during the acceleration phase. We present results from recent experiments at the OMEGA laser facility. These experiments were designed as a proof-of-principle for the platform, using the same cylinder exterior dimensions and direct-drive beam configuration as previous single cylinder experiments. In these experiments, three sets of targets were fielded: no machined perturbations (smooth), a sinusoidal mode-10 perturbation on the outer surface of the inner cylinder, and a mode-20 perturbation on the outer surface of the inner cylinder. The primary diagnostic was a gated x-ray framing camera which imaged the backlit inner cylinder on-axis for sixteen frames over a time window of 1 ns for each shot. A second side-lit radiograph captured one image per shot, diagnosing axial uniformity. In this report we include an overview of the results from both the backlighter and the sidelighter diagnostics. We discuss at length the experimental analysis process. Finally, we present the results of the smooth target implosion trajectory and compare them to post-shot simulations. We see favorable agreement between simulation and experiment.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Preshot Report for OMEGA Double Cylinders (CylDRT 22B)

The primary goals for the May 2022 shot day at OMEGA are to: image an imploding inner cylinder as proof-of-principle for double cylinder experiments, measure the growth of pre-seeded perturbations on the inner cylinder, and measure the axial non-uniformity of the implosion with a sidelighter that provides a transverse view of the target. We will compare these experimental results to xRAGE (2D-only) and FLASH (2D and 3D) radiation-hydrodynamics calculations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Preshot Report for the NIF DDCyl Campaign: H_Hyd_DDCyl_DRT_AAA/BBB/CCC

The first two cylinder shot days on the National Ignition Facility, allocated through the Discovery Science program, provided a successful demonstration of the cylinder platform on the NIF. Both of these shot days used cylinders that were nominally 3 times larger in radial dimension than cylinders fielded at the OMEGA laser facility, here referred to as scale-3 targets. In the first Discovery Science shot day, we demonstrated that Rayleigh-Taylor instability growth during the deceleration phase is scale-invariant between the scale-1 OMEGA experiments and similarly tailored scale-3 NIF experiments at the same convergence ratio of CR=initial radius/final radius=2.25. In the second Discovery Science shot day, we increased the convergence ratio by lowering the density of the central foam from 300 mg/cm 3 to roughly 40 mg/cm 3 with the same laser drive, resulting in a higher CR=5 at the time when the rebounding shock strikes the aluminum marker. We also greatly improved the imaging setup for the second shot day, resulting in much higher quality (greater signal-to-noise) radiographs of the implosion. This current shot day was awarded through the High Energy Density (HED) Council, following this demonstration of platform viability. It was originally scheduled for June 2020, but it was postponed several times due to the COVID-19 pandemic. It is currently scheduled for January 6, 2021. For this shot day, we will increase the radial dimension of the cylinder to four times the OMEGA-scale targets, and these will be referred to as scale-4 cylinders. Increasing the radial dimension of the target is advantageous as we push these targets to higher convergence ratio. By starting with an initially larger target, the target can push to a higher CR while maintaining the same final viewing area. Other than the larger radial dimension, the targets are very similar in design to the previous ones, consisting of an epoxy ablator, an embedded aluminum marker layer, and a low density central CH foam. These will also use a 40 mg/cm3 CH foam, reaching a CR~4.5 with the same laser energy (the added target mass reduces the final CR slightly). Note that this is NOT designed to be scale-invariant with the previous scale-1 OMEGA and scale-3 NIF shots. It was determined that the laser energy required to achieve a scale-invariant implosion was above the allowable optics damage limits (though achievable on the NIF) for these scale-4 targets.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Streaked optical pyrometer for proton-driven isochoric heating experiments of solid and foam targets

We have designed, built, and calibrated an ultrafast streaked optical pyrometer (SOP) with ~5 ps resolution for measuring the time-resolved surface blackbody temperature of an isochorically heated plasma. The pyrometer is calibrated to measure temperatures from 0.5 eV to 25 eV, with the option of adding calibrated neutral density filters to observe hotter plasmas. We demonstrated the use of this pyrometer on isochoric heating experiments using laser-accelerated proton beams as an energy source at the $f$ /40 beamline of the Texas Petawatt Laser. We used the large focal spot size (~80 μm radius) of the $f$ /40 pulses to accelerate high numbers of ~MeV protons off 5 μm thick solid gold targets. During our experimental campaign, we heated 10 μm thick aluminum foil targets to 1–10 eV over a duration of 50 ps and also observed heating to ~2 eV in 100 μm thick 60 mg/cm 3 carbon foams using the SOP to measure both the temperature and heating timescale.

Equations of state↗