Engineering topics

Roylance, D.

Publications and source records attributed to Roylance, D..

7 records

NASA NTRS1985

Automatic Processing of Reactive Polymers

A series of process modeling computer codes were examined. The codes use finite element techniques to determine the time-dependent process parameters operative during nonisothermal reactive flows such as can occur in reaction injection molding or composites fabrication. The use of these analytical codes to perform experimental control functions is examined; since the models can determine the state of all variables everywhere in the system, they can be used in a manner similar to currently available experimental probes. A small but well instrumented reaction vessel in which fiber-reinforced plaques are cured using computer control and data acquisition was used. The finite element codes were also extended to treat this particular process.

Roylance, D.↗

NASA NTRS1984

Analysis of cure in composites processing

Finite element analysis is a general numerical tool for solving the field equations of engineering practice, and this paper demonstrates its use in modeling the nonisothermal cure of pultruded composite material. A very simple grid is used in this case to model a narrow strip of material, and this grid is then solved using a time-stepping transient algorithm to simulate the passage of the strip along the pultruder die. As time proceeds, heat is conducted into the strip from the heated boundaries at the die walls, and cure proceeds at a rate dependent on the local temperature. The computer model can be used to minimize the time needed for sufficient cure, and helps avoid such processing errors as undercure or thermal degradation.

Aylward, L.↗

NASA NTRS1982

Chemorheology of reactive systems: Finite element analysis

The equations which govern the nonisothermal flow of reactive fluids are outlined, and the means by which finite element analysis is used to solve these equations for the sort of arbitrary boundary conditions encountered in industrial practice are described. The performance of the computer code is illustrated by several trial problems, selected more for their value in providing insight to polymer processing flows than as practical production problems. Although a good deal remains to be learned as to the performance and proper use of this numerical technique, it is undeniably useful in providing better understanding of today's complicated polymer processing problems.

Douglas, C.↗

NASA NTRS1982

Numerical modeling and optimization of polymer melt processing operations

The application of finite element computer analyses to polymer flows of the type encountered in melt processing operations is described. A code capable of predicting values of fluid veleocity, pressure, shear stress, and temperature at any point within the flow field was developed. As such, is is of value in diagnosing such processing problems as regions of fluid stagnation at which thermal degradation may occur, or regions of excessive shear deformation which lead to thermomechanical damage. It is further able to generate predictions of the forces which must be applied to the melt to achieve the desired flow, and this information is of value in designing processing equipment of optimal efficiency and minimum energy consumption.

Roylance, D.↗

NASA NTRS1982

Finite element analysis of nonisothermal polymer processing operations

A finite element formulation for the analysis of polymer processing is presented and its use in some typical situation including entry flow, transient Couette flow, and the Graetz (forced convection) problem is illustrated. The element formulations are constructed on the premise that momentum convection can be neglected (polymer melt flows typically have very low Reynolds' numbers), but that convective heat transfer may be significant (high Peclet numbers). Nonisothermal effects are considered important in polymer processing, due in part to the significant heating which may occur due to viscous dissipation, and also to the very strong influence of temperature on fluid viscosity. The flow is treated as Newtonian with the flow field being coupled to the heat transfer equation only through the viscous heat generation.

Douglas, C.↗

NASA NTRS1981

Finite element modeling of nonisothermal polymer flows

A finite element formulation designed to simulate polymer melt flows in which both conductive and convective heat transfer are important is described, and the numerical model is illustrated by means of computer experiments using extruder drag flow and entry flow as trial problems. Fluid incompressibility is enforced by a penalty treatment of the element pressures, and the thermal convective transport is modeled by conventional Galerkin and optimal upwind treatments.

Roylance, D.↗

NASA NTRS1977

Numerical analysis of projectile impact in woven texile structures

Computer codes were developed for simulating the dynamic fracture and viscoelastic constitutive response due to stress wave interaction and reflections caused by ballistic impact on woven textiles. The method, which was developed for use in the design and analysis of protection devices for personnel armor, has potential for use in studies of rotor blade burst containment at high velocity. Alterations in coding required for burst containment problems are discussed.

Roylance, D.↗