Search NASA⌕ Search

Engineering topics

Rudakov, D. L. (ORCID:0000000252664269)

Publications and source records attributed to Rudakov, D. L. (ORCID:0000000252664269).

11 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Turbulent drifts of impurity ions as an explanation for anomalous radial transport in the far-SOL of DIII-D

Abstract Successful fusion reactor operation relies on minimal core contamination by impurities, otherwise too much power may be radiated and harm performance. This requires reliable predictions of impurity transport from the scrape-off layer (SOL) into the core, beyond the traditional ‘anomalous’ diffusion approach. We report a set of far-SOL tungsten transport simulations that demonstrate the role of turbulent drifts on radial impurity transport. A turbulent plasma background is simulated using the gyrokinetic SOL code Gkeyll. Tungsten ions are followed within the plasma background using only their drifts. We find that tungsten tends to travel radially outwards with velocities between v r = 300–1200 m s −1 primarily due to polarization drift. We also extract an anomalous radial diffusion coefficient that varies from D r anom = 5–20 m 2 s −1 . These results are compared to and agree with previous interpretive modeling results. We also show how the turbulent polarization drift can transport some tungsten ions from the wall inwards with effective pinch velocities up to 10 000 m s −1 . We conclude that turbulent drifts are a likely explanation for historically anomalous radial impurity transport.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Filamentary velocity scaling validation and spin dynamics in the DIII-D tokamak

Measured filament velocities in the DIII-D tokamak are compared against theoretical scalings, finding that the latter often represents an upper limit on experimental velocity distributions with most filaments possessing lower velocity. Filament spin from internal E × B drift is experimentally demonstrated to alter filament radial velocity. A critical spin velocity, where filament radial velocity peaks, is observed and corresponds to approximately 5 km/s. This transition is corroborated using a less direct measure of filament spin in the form of a temperature ratio. These techniques are combined to find that the critical spin velocity closely aligns with transport times along and across filaments becoming comparable. The normalized filament size distribution is consistent with the most stable size as dictated by Kelvin–Helmholtz and curvature-driven instabilities. Overall, the findings suggest filament stability and spin alter filamentary transport that may threaten the integrity of first walls in fusion devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Experimental evidence of enhanced radial transport in small ELM regimes at DIII-D

Small/type-II edge-localized-modes (ELMs), carrying 1% of the plasma stored energy, are found to deposit only 45 ± 5% of the ELM power near the strike point, and the remaining 55 ± 5% to the far scrape-off-layer (SOL). Small ELMs spread their power over a larger area compared to type-I ELMs, where such a ratio is about 60% and 40% for near- and far-SOL regions, respectively. The larger spread is reflected in the heat flux width (λq) in the SOL for the intra-small ELMs profile of 6.0 mm, almost a factor 2 larger than that of type-I ELMs of 3.15 mm, for similar plasma conditions and magnetic configuration. At the ELM peak, the small ELMs λq is found to be up to 4 times larger than for the type-I ELMs, going from 2 to 7.9 mm, indicating enhanced radial transport in the neon-seeded small ELM scenario. Inter-ELM λqs have been also calculated at the secondary outer divertor in quasi-double-null (QDN) discharges. It is found that, on average, λq is 2.2 times larger in the high-separatrix-density small ELM regime, compared to a reference type-I ELM one. These findings are supported by small ELMs radial velocity profiles, measured at the outer midplane with a fast reciprocating probe, showing a decay length (λvr) in the SOL of 12.8 cm, which is 3.3 times larger than that for the type-I ELMs of 3.9 cm. This analysis shows that small ELMs, although attractive for future machines due to low peak heat flux and large λq, might be of concern for the larger flux to the outer wall.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Recent DIII-D progress toward validating models of tungsten erosion, re-deposition, and migration for application to next-step fusion devices

Abstract Fundamental mechanisms governing the erosion and prompt re-deposition of tungsten impurities in tokamak divertors are identified and analyzed to inform the lifetime of tungsten plasma-facing components in ITER and other future devices. Various experiments conducted at DIII-D to benchmark predictive models are presented, leveraging the DiMES removable sample exposure probe capability and the Metal Rings Campaign, in which toroidally symmetric rows of tungsten-coated tiles were installed in the DIII-D divertor. In tokamak divertors, the width of the electric sheath is of the order of the main ion Larmor radius, and a vast majority of sputtered tungsten impurities are typically ionized within the sheath. Therefore, W prompt redeposition is mainly governed by the ratio of the characteristic ionization mean-free path of neutral tungsten to the width of the sheath. In-situ monitoring of the prompt redeposition of tungsten impurities in divertors is demonstrated via the use of WII/WI line ratios and the ionizations/photon (S/XB) method in L-mode discharges. Even with this relatively limited set of emission measurements, net erosion measurements were found to be a consistent upper bound to an analytic scaling based on the ratio of the W ionization length, λ iz , and the width of the magnetic sheath rather than the ratio of λ iz and the W + gyro-radius. In the far-scrape-off layer (SOL) of the ITER divertor, however, it is calculated that the measurement of photon emissions associated with the ionization of tungsten impurities up to W 5 + may be required. Finally, W deposition patterns on DiMES collector probes, interpreted via DIVIMP-WallDYN modelling, reveal the key roles of progressive W erosion/re-deposition staps and E × B drifts in regulating long-range high-Z material migration.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

In-situ coating of silicon-rich films on tokamak plasma-facing components with real-time Si material injection

Abstract Experiments have been conducted in the DIII-D tokamak to explore the in-situ growth of silicon-rich layers as a potential technique for real-time replenishment of surface coatings on plasma-facing components (PFCs) during steady-state long-pulse reactor operation. Silicon (Si) pellets of 1 mm diameter were injected into low- and high-confinement (L-mode and H-mode) plasma discharges with densities ranging from 3.9– 7.5 × 10 19 m −3 and input powers ranging from 5.5 to 9 MW. The small Si pellets were delivered with the impurity granule injector at frequencies ranging from 4 to 16 Hz corresponding to mass flow rates of 5–19 mg s −1 (1– 4.2 × 10 20 Si s −1 ) at cumulative amounts of up to 34 mg of Si per five-second discharge. Graphite samples were exposed to the scrape-off layer and private flux region plasmas through the divertor material evaluation system to evaluate the Si deposition on the divertor targets. The Si II emission at the sample correlates with silicon injection and suggests net surface Si-deposition in measurable amounts. Post-mortem analysis showed Si-rich coatings containing silicon oxides, of which SiO 2 is the dominant component. No evidence of SiC was found, which is attributed to low divertor surface temperatures. The in-situ and ex-situ analysis found that Si-rich coatings of at least 0.4–1.2 nm thickness have been deposited at 0.4–0.7 nm s −1 . The technique is estimated to coat a surface area of at least 0.94 m 2 on the outer divertor. These results demonstrate the potential of using real-time material injection to form Si-enriched layers on divertor PFCs during reactor operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Developing solid-surface plasma facing components for pilot plants and reactors with replenishable wall claddings and continuous surface conditioning. Part A: concepts and questions

Abstract It is estimated that pilot plants and reactors may experience rates of net erosion and deposition of solid plasma facing component (PFC) material of 10 3 –10 5 kg yr −1 . Even if the net erosion (wear) problem can be solved, the redeposition of so much material has the potential for major interference with operation, including disruptions due to so-called ‘unidentified flying objects (UFOs)’ and unsafe dust levels. The potential implications appear to be no less serious than for plasma contact with the divertor target: a dust explosion or a major UFO-disruption could be as damaging for an actively-cooled deuterium-tritium (DT) tokamak as target failure. It will therefore be necessary to manage material deposits to prevent their fouling operation. This situation appears to require a fundamental paradigm shift with regard to meeting the challenge of taming the plasma–material interface: it appears that any acceptable solid PFC material will in effect be flow-through , like liquid–metal PFCs, although at far lower mass flow rates. Solid PFC material will have to be treated as a consumable , like brake pads in cars. ITER will use high-Z (tungsten) armor on the divertor targets and low-Z (beryllium) on the main walls. The ARIES-AT reactor design calls for a similar arrangement, but with SiC cladding on the main walls. Non-metallic low-Z refractory materials such as ceramics (graphite, SiC, etc) used as in situ replenishable, relatively thin—of order mm—claddings on a substrate which is resistant to neutron damage could provide a potential solution for the main walls, while reducing the risk of degrading the confined plasma. Separately, wall conditioning has proven essential for achieving high performance. For DT devices, however, standard methods appear to be unworkable, but recently powder droppers injecting low-Z material ∼continuously into discharges have been quite effective and may be usable in DT devices as well. The resulting massive generation of low-Z debris, however, has the same potential to seriously disrupt operation as noted above. Powder droppers provide a unique opportunity to carry out controlled studies on the management of low-Z slag in all current tokamaks, independent of whether their protection tiles use low-Z or high-Z material.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Developing solid-surface plasma facing components for pilot plants and reactors with replenishable wall claddings and continuous surface conditioning. Part B: required research in present tokamaks

Abstract The companion part A paper (Stangeby et al 2022) reports a number of independent estimates indicating that high-duty-cycle DT tokamaks starting with pilot plants will likely experience rates of net erosion and deposition of solid PFC, plasma facing component, material in the range of 10 3 to 10 4 kg yr −1 , regardless of the material used. The subsequent redeposition of such large quantities of material has the potential for major interference with tokamak operation. Similar levels and issues will be involved if ∼continuous low-Z powder dropping is used for surface conditioning of DT tokamaks, independent of the material used for the PFC armor. In Stangeby et al (2022) (part A) it is proposed that for high-duty-cycle DT tokamaks, non-metallic low-Z refractory materials such as ceramics (graphite, SiC, etc) used as in situ replenishable, relatively thin—of order mm—claddings on a substrate which is resistant to neutron damage could provide a potential solution for protecting the main walls, while reducing the risk of degrading the confined plasma. Assessment of whether such an approach is viable will require information, much of which is not available today. Section 6 of part A identifies a partial list of major physics questions that will need to be answered in order to make an informed assessment. This part B report describes R&D needed to be done in present tokamaks in order to answer many of these questions. Most of the required R&D is to establish better understanding of low-Z slag generation and to identify means to safely manage it. Powder droppers provide a unique opportunity to carry out controlled studies on the management of low-Z slag in current tokamaks, independent of whether their protection tiles use low-Z or high-Z material.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

The role of B T -dependent flows on W accumulation at the edge of the confined plasma

Abstract Near-separatrix impurity accumulation between the crown and the outer midplane of tokamaks is a common feature in results from codes such as SOLPS-ITER and DIVIMP; however, experimental evidence of accumulation has only recently been obtained and is reported here. The codes find that the poloidal distribution of impurity ions in the scrape-off layer (SOL) depends primarily on toroidal field ( B T )-dependent parallel flow patterns of the background plasma and the parallel ion temperature gradient (∇ ‖ T ion ) force. Experimentally, Mach probes used in L-mode plasmas with favorable (for H-mode access) B T measure fast ( M ∼ 0.3–0.5) inner-target-directed (ITD) background plasma flows at the crown of single-null discharges. This study reports a set of DIVIMP simulations for two similar H-mode discharges from the DIII-D W metal rings campaign differing primarily in B T -direction to assess the effect that fast ITD flows have on the distribution of W ions in the SOL. It is found that for imposed ITD flows of M = 0.3, W ions that otherwise accumulate due to the ∇ ‖ T ion -force are largely flushed out. It is also found that doubling the radial diffusion coefficient from 0.3 to 0.6 m 2 s −1 prevents accumulation due to rapid cross-field transport into the far-SOL, where background plasma flows drain W ions to the divertors. Far-SOL W distributions from DIVIMP are then used to specify input to the impurity transport code 3DLIM, which is used to interpretively model collector probe (CP) deposition patterns measured in the ‘wall-SOL’. It is demonstrated that the deposition patterns are consistent with the DIVIMP predictions of near-SOL accumulation for the unfavorable- B T direction, and little/no accumulation for the favorable- B T direction. The wall-SOL CPs have thus provided the first experimental evidence, albeit indirect, of near-SOL W accumulation—finding it occurs for the unfavorable- B T direction only. For the favorable- B T direction, fast flows can largely prevent accumulation from occurring.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Modeling, analysis, and code/data validation of DIII-D tokamak divertor experiments on ELM and non-ELM plasma tungsten sputtering erosion

Abstract We analyzed recent DIII-D tokamak tungsten divertor probe experiments using advanced, coupled, sputter erosion/redeposition, plasma, and surface response code packages. Modeling is done for ELMing H-mode, and L-mode plasmas, impinging on various size tungsten deposits on Divertor Material Evaluation System (DiMES) carbon probes. The simulations compute 3D, full kinetic, sub-gyromotion, impurity sputtering and transport, including changes in tungsten surface composition and response due to mixed deuterium and carbon ions irradiation. Per our analysis, ELM (edge localized mode) plasma sputtering in DIII-D mostly involves free-streaming high energy (∼500–1000 eV) D + and C +6 ions, with high near-surface plasma density. L-Mode sputtering is due to impurity sputtering (C, W) only, with lower density. All cases show complete redeposition of tungsten on the divertor, with significant redeposition on the tungsten spots themselves, and low self-sputtering. Comparison of ELM plasma gross tungsten erosion simulation results with in-situ spectroscopic data is good, as are code/data comparisons of net erosion using post-exposure Rutherford backscattering (RBS) data for the L-mode probes. The analysis, extrapolated to a full tungsten divertor, implies low net erosion and negligible plasma contamination from sputtering. These results support the use of high-Z plasma facing surfaces in ITER and beyond.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗