Engineering topics
Publications and source records attributed to Ruddy, Daniel (ORCID:0000000326543778).
Cu/BEA was synthesized via incipient wetness impregnation with Cu(NO)3-2.5H2O to achieve 5 wt.% Cu loading. Bronsted acid sites were quantified with isopropylamine temperature programmed desorption.
The conversion of lignocellulosic-derived carbon sources via the creation of a CO2 rich syngas stream provides means to produce liquid hydrocarbon fuels, with advancements intended to create a cost-competitive method of sequential conversion via methanol and dimethyl ether intermediates. Previously developed methods with Cu/Beta zeolites enabled the conversion of dimethyl ether to linear and branched hydrocarbons, with high selectivities towards products with high-octane fuel properties. Through process intensification, use of a single reactor to convert syngas to methanol and DME, then further to hydrocarbons, allows for reduced capitol and operation cost for the same chemistries that typically use 3 reactors instead of one. Utilization of commercially available methanol synthesis catalyst (Megamax 800, Clariant, CZA) and methanol dehydration catalyst with the Cu/Beta catalyst allowed for conversion into hydrocarbon products in this single reactor set up. Reactor configuration with CZA and alumina catalysts mixed with or stacked in a bed physically above the Cu/Beta catalyst provided a system for the direct conversion of the syngas to hydrocarbons with improved yields and selectivities with higher net C1 conversions for stacked bed configurations. Through control of the process conditions, greater conversion of C1 oxygenate intermediates (i.e., methanol and dimethyl ether) was achieved with concomitant increase in selectivities towards gasoline and jet fuel range olefin and paraffin products. Lower hydrocarbon number products and less naphthenes were observed for the conversion of syngas compared to DME conversion on only the Cu/Beta system with prominent selectivities observed for C4, C5, and C7 hydrocarbons. The DME and methanol formation rates, with understanding of the equilibria for both processes, were determined as important factors to allow for improved performance of the Cu/Beta. Determination of the factors which allow for tuning of selectivities and yields created an intensified process which allows for a "market-responsive" biorefinery design, which can produce high octane gasoline or jet fuel range hydrocarbons to meet demands for a more sustainable route to liquid fuels.
As the world endures environmental crises associated with climate change and the rise of atmospheric CO2 concentrations from anthropogenic CO2 emission, carbon capture and utilization (CCU) technologies are increasingly necessary. Reactive carbon capture (RCC) technologies, in which capture and conversion of CO2 occur in a single reactor, are more energetically and economically attractive by avoiding the need to purify, compress, and transport the captured CO2. To this end, the development of dual function materials (DFM) that enable CO2 capture and conversion to useful C1 products, namely (1) methane, (2) CO, and (3) methanol, are attractive near-term targets for commercial CCU processes for renewable fuels and chemicals. DFM are composed of sorbents and catalysts co-dispersed on the same high surface area carrier. The sorbent component allows for selective capture of CO2 from a gas stream and the catalyst component subsequently performs the in-situ conversion of the adsorbed CO2 upon introduction of a reactive gas (typically H2). The survey of DFM formulations reveals a variety of sorbent+catalyst combinations of interest. There is, however, a lack of depth in fundamental understanding of how the CO2 binds to these materials and how the subsequent reaction mechanisms are affected, which are critical features for the development of next-generation materials with improved performance. To this end, we will describe in this work the CO2 binding characteristics of established and/or new DFM and their sorbent-only counterparts. The surface CO2 binding mechanism and capture capacity will be probed using techniques such as in-situ DRIFTS, operando TGA, and CO2 chemisorption.
This project is developing the centerpiece technology for a market-responsive, integrated biorefinery concept based on the conversion of renewable C1 intermediates (e.g., syngas, CO2, methanol) to a suite of fuels and co-products with improved carbon efficiency, reduced capital expense, and control of the product distribution to meet market demand. Advanced upgrading technologies of syngas are critically needed for the successful commercialization of fuel production at a scale relevant for biomass gasification. Research tasks within this project leverage complementary catalyst and process design for the conversion of CO2-rich syngas (15-20% CO2 in syngas) to achieve high carbon yields of gasoline and jet fuels as the major products. The conversion pathways generate high quality fuels (e.g., high octane gasoline with low aromatics, desirable jet-range hydrocarbons), and potential to achieve favorable cost targets by 2022. Research progress is compared against the Mobil Olefin to Gasoline and Distillate (MOGD) process, which also offers control over the gasoline and distillate products, as an industrial benchmark. The pathway for direct conversion of CO2-rich syngas to hydrocarbon fuels seeks to exceed the carbon efficiency of biomass-sourced MOGD (31.8%). Recent catalyst and process development achievements are highlighted by improvements in carbon-selectivity to fuels and carbon yields, along with evidence of incorporation of carbon from CO2 into the hydrocarbon products.