Search NASA⌕ Search

Engineering topics

Rupich, Marty

Publications and source records attributed to Rupich, Marty.

YBCO Coated Conductor with an Integrated Optical Fiber Sensor

The primary objectives of the Phase I Project was to develop a proof-of-principle for a concept of integrating an optical fiber sensor into the laminated 2G wire, there by producing a functionalized 2G wire with self-monitoring capabilities

47 OTHER INSTRUMENTATION↗

Examination of Through-Thickness/Through-Time Phase Evolution during an MOD-Type REBCO Precursor Conversion Using Raman Microsscopy

Through-thickness/through-time composition analyses were made on REBa{sub 2}Cu{sub 3}O{sub 6+x} (REBCO) films prepared from metal-organic deposited (MOD) precursors on a RABiTS (rolling-assisted biaxially textured substrate) template. Y Dy{sub 0.5}Ba{sub 2}Cu{sub 3}O{sub 6 + x} films were fabricated either by a single precursor coating or by two separate, equivalent precursor coatings with an intermediate decomposition. Specimens were quenched at selected times along a heat treatment profile that simulated conditions used by American Superconductor, then examined by Raman microscopy along mechanically milled slopes through the REBCO films. Upon reaching the reaction temperature TR, the precursor initially transforms into a (Y, Dy){sub 2}Cu{sub 2}O{sub 5}, CuO, Cu{sub 2}O, and RE-Ba-F-O phase mix, and this is followed shortly by substrate level REBCO formation that propagates upwards through time. Our results indicate that (1) the single layer (SL) and double layer (DL) films (both {approx} 1.2 {mu}m thick) react to completion at about the same rate and arrive at a similar final composition and (2) some residual Ba-Cu-O phases persist near the top of the fully reacted films. The performance of the SL film was moderately better than that of the DL film, seemingly due to better through-thickness REBCO texture as determined using x-ray diffraction.

36 MATERIALS SCIENCE↗

A Phase Relation Study of Ba-Y-Cu-O Coated-Conductor Films Using the Combinatorial Approach

Phase relationships in bulk and thin film Ba-Y-Cu-O high-Tc superconductor system were determined at processing conditions relevant for industrial production of coated conductors. Our results demonstrated that the absence of BaY2CuO5 (which has a critical effect on flux pinning) at 735 C--a typical temperature employed in production of coated conductors--in thin films processed in situ from the BaF2 precursor is caused by the sluggish reaction kinetics rather than by the presence of fluorine in the system. Thermodynamic calculations combined with annealing experiments confirmed that BaY2CuO5 is thermodynamically stable but forms at temperatures higher than 735 C.

36 MATERIALS SCIENCE↗

Influence of Oxygen Deficiency on the Out-of-Plane Tilt of Epitaxial Y 2 O 3 Films on Ni-5%W Tapes

We analyzed the crystallographic c-axis tilt of (001) Y 2 O 3 films grown on biaxially textured Ni-5%W tapes under different oxygen flux conditions. We found that different tilting mechanisms were effective in films with different oxygen stoichiometry. Moreover, the structure of the film/substrate interface, investigated by TEM, and the residual strain of the film, investigated by XRD, were also dependent on the film oxygen content. While the oxygen stoichiometric Y 2 O 3 sample exhibited a coherent film/substrate interface and the sharpest out-of-plane texture, the films grown under reduced oxygen pressure exhibited a smaller overall c-axis tilt due to formation of interface dislocations and regions in which the film oxygen vacancies ordered to form a lattice superstructure.

36 MATERIALS SCIENCE↗

A Modular Ex Situ Conversion Process for Thick MOD-Fluoride RBCO Precursors

Following a review of heating induced chemical and structural changes in RBa2Cu3O7 (RBCO) fluoride precursors (R= rare earth of Y) deposited by metalorganic (MOD) and physical vapor deposition (PVD), a modular process comprising successive, functionally distinct, brief annealing steps (modules) is introduced. By decoupling events that otherwise occur simultaneously, the modular process provides a framework for addressing the complex kinetics associated with the temperature ramp of the ex situ conversion anneal. Modules for modifying the F concentration, porosity and microstructure, and RBCO nucleation are described.

36 MATERIALS SCIENCE↗

Progress in Nanoengineered Microstructures for Tunable High-Current, High-Temperature Superconducting Wires

High critical current densities (J{sub c}) in thick films of the Y{sub 1}Ba{sub 2}Cu{sub 3}O{sub 7-{delta}} (YBCO, {Tc}{approx}92 K) superconductor directly depend upon the types of nanoscale defects and their densities within the films. A major challenge for developing a viable wire technology is to introduce nanoscale defect structures into the YBCO grains of the thick film suitable for flux pinning and the tailoring of the superconducting properties to specific, application-dependent, temperature and magnetic field conditions. Concurrently, the YBCO film needs to be integrated into a macroscopically defect-free conductor in which the grain-to-grain connectivity maintains levels of inter-grain J{sub c} that are comparable to the intra-grain J{sub c}. That is, high critical current (I{sub c}) YBCO coated conductors must contain engineered in homogeneities on the nanoscale, while being homogeneous on the macroscale. An analysis is presented of the advances in high-performance YBCO coated-conductors using chemical solution deposition (CSD) based on metal trifluoroacetates and the subsequent processing to nano-engineer the microstructure for tunable superconducting wires. Multi-scale structural, chemical, and electrical investigations of the CSD film processes, thick film development, key microstructural features, and wire properties are presented. Prospects for further development of much higher I{sub c} wires for large-scale, commercial application are discussed within the context of these recent advances.

36 MATERIALS SCIENCE↗