Search NASA⌕ Search

Engineering topics

Söderlind, Per

Publications and source records attributed to Söderlind, Per.

14 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Thermodynamics and Magnetism of SmFe 12 Compound Doped with Zr, Ce, Co and Ni: An Ab Initio Study

Alloys that are Ni-doped, such as the (Sm 1—y Zr y )(Fe 1—x Co x ) 12 and (Ce 0.5 Sm 0.5 )Fe 10 Co 2 systems, are studied because of their magnetic properties. The (Sm 1—y Zr y )(Fe 1—x Co x ) 11—z Ti z and (Ce. 1—x Sm x )Fe 9 Co 2 Ti alloys are considered contenders for vastly effective permanent magnets because of their anisotropy field and Curie temperature. Ti can act as a stabilizer for the SmFe 12 compound but substantially suppresses saturation magnetization. To maintain the saturation magnetization in the scope of 1.3–1.5 T, we propose substituting a particular quantity of Fe and Co in the (Sm 1—y Zr y )(Fe 1—x Co x ) 12 and (Ce 0.5 Sm 0.5 )Fe 10 Co 2 alloys with Ni. By performing ab initio calculations, we show that Ni incorporation results in increased thermodynamic stability and, in contrast to Ti, has a parallel spin moment aligned to the moment of the SmFe 12 compound and improves its saturation magnetization without affecting the anisotropy field or Curie temperature.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Lattice dynamics and thermodynamics for δ -plutonium from density functional theory

Here, we present results from density functional theory (DFT) calculations of the lattice dynamics (phonons) and thermodynamics for δ-phase plutonium. The fully relativistic electronic structure is calculated assuming a three-dimensional noncollinear magnetic structure in conjunction with DFT and the general gradient approximation for the electron exchange and correlation interactions. The electronic-structure model is further enhanced by addressing strong orbital-orbital coupling via the conventional orbital-polarization (OP) scheme as has been successfully done for plutonium. The temperature dependence of the phonons is calculated within the self-consistent ab initio lattice dynamics approach. The obtained phonons compare very well with measurements although a modest overestimation of the transverse L-point [ξξξ] phonon is acknowledged. Calculated thermal vibration amplitudes and the associated Debye-Waller temperatures are close to experiments. Lattice, electronic, and magnetic contributions to the heat capacity are predicted and consistent to a few percent with that deduced from experimental data. Good agreement is only achieved when a magnetic contribution to the specific heat is recognized. The parameter-free DFT+OP electronic model is thus capable of predicting phonon properties and thermodynamic behavior of δ-phase plutonium rather accurately.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Refined room-temperature equation of state of Bi up to 260 GPa

At room temperature, bismuth undergoes several structural transitions with increasing pressure before taking on a body-centered cubic (bcc) phase at approximately 8 GPa. The bcc structure is stable to the highest measured pressure and its simplicity, along with its high compressibility and atomic number, makes it an enticing choice as a pressure calibrant. Here, we present three data sets on the compression of bismuth in a diamond anvil cell in a neon pressure medium, up to a maximum pressure of about 260 GPa. The use of a soft pressure medium reduces deviatoric stress when compared to previous work. With an expanded pressure range, a higher point density, and a decreased uniaxial stress component, we are able to provide more reliable equation of state parameters. We also conduct density functional theory electronic-structure calculations that confirm that the bcc phase is energetically favored at high pressure.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

High-Temperature Thermodynamics of Uranium from Ab Initio Modeling

We present high-temperature thermodynamic properties for uranium in its γ phase (γ-U) from first-principles, relativistic, and anharmonic theory. The results are compared to CALPHAD modeling. The ab initio electronic structure is obtained from density-functional theory (DFT) that includes spin–orbit coupling and an added self-consistent orbital-polarization (OP) mechanism for more accurate treatment of magnetism. The first-principles method is coupled to a lattice dynamics scheme that is used to model anharmonic lattice vibrations, namely, Self-Consistent Ab Initio Lattice Dynamics (SCAILD). The methodology can be summarized in the acronym DFT + OP + SCAILD. Upon thermal expansion, γ-U develops non-negligible magnetic moments that are included for the first time in thermodynamic theory. The all-electron DFT approach is shown to model γ-U better than the commonly used pseudopotential method. In addition to CALPHAD, DFT + OP + SCAILD thermodynamic properties are compared with other ab initio and semiempirical modeling and experiments. Our first-principles approach produces Gibbs free energy that is essentially identical to CALPHAD. The DFT + OP + SCAILD heat capacity is close to CALPHAD and most experimental data and is predicted to have a significant thermal dependence due to the electronic contribution.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

High-Temperature Thermodynamics Modeling of Graphite

We present high-temperature thermodynamic properties for graphite from first-principles anharmonic theory. The ab initio electronic structure is obtained from density-functional theory coupled to a lattice dynamics method that is used to model anharmonic lattice vibrations. This combined approach produces free energies and specific heats for graphite that compare well with available experiments and results from models that empirically represent experimental data, such as CALPHAD. We show that anharmonic theory for the phonons is essential for accurate thermodynamic quantities above about 1000 K.

36 MATERIALS SCIENCE↗
DOE OSTI2022

High-pressure structural systematics of dysprosium metal compressed in a neon pressure medium to 182 GPa

Here we present an experimental and theoretical study of dysprosium metal compressed in the soft pressure transmitting medium Ne up to 182 and 300 GPa, respectively. Angle-dispersive x-ray powder diffraction data from each of the high-pressure polymorphs shows anisotropic compression behavior indicating changes to the electron density distribution throughout its polymorphic landscape. We compare the monoclinic (mC4) and orthorhombic (oF16) structures for the collapsed structure for Dy above 82 GPa and verify that the oF16 structure offers a better fit to our data than the previously reported mC4 structure. Further, we have found that the oF16 structure undergoes similar anisotropic compression of its lattice parameters, with a turning point above 160 GPa; suggesting a potential phase transition at pressures much higher than achieved in this study. Density functional theory calculations show the likely candidate for this new high-pressure phase is the isosymmetric oF8 structure, which is predicted to be lower in energy than the oF16 structure above 275 GPa.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Ab initio calculations for void swelling bias in α - and δ -plutonium

Void swelling can develop in materials under persistent irradiation when nonequilibrium vacancy and self-interstitial populations migrate under sufficiently asymmetric interaction biases. In conventional metals, the propensity is determined to the first approximation by comparing point-defect relaxation strains. We thus present DFT-based calculations of structures and formation energies and volumes of point defects in the α and the δ phases of plutonium. Here we discuss the pros and cons of various levels of electronic structure theory: spin polarization, spin-orbit coupling, and orbital polarization. Our results show that lattice defects in δ-Pu, in contrast to most fcc metals, have surprisingly small formation volumes. Equally unexpected are the large defect formation volumes found in the low-symmetry α-Pu phase. Both these unusual properties can be satisfactorily explained from defect-induced spin/orbital moment formation and destruction in the Pu phases. Surprisingly, the point defects in α-Pu are found to induce far larger transformation of the local electronic structure than in δ-Pu. When we use the calculated defect properties to estimate the classic void swelling bias in each of the phases, we find it to be unusually small in δ-Pu but likely much larger in α-Pu. Hence, swelling rates and mechanisms can diverge dramatically between the different phases of Pu. Especially in the transient regime before the formation of large defect clusters, the swelling rate of α-Pu can reliably be expected to be much larger than δ-Pu. However, accurate forecasts over longer times will require the conventional void-swelling theory to be modified to handle the complexities presented by the different Pu phases. As a case in point, we show the possible anomalous temperature dependence of vacancy properties in δ-Pu, caused by entropic contributions from defect-induced spin-lattice fluctuations. Such complications may affect defect-defect interactions and thus alter the void swelling bias.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Thermodynamics Modeling for Actinide Monocarbides and Mononitrides from First Principles

The high-temperature thermodynamical properties for the actinide monocarbides and mononitrides ThC, ThN, UC, UN, PuC, and PuN are calculated from first-principles electronic-structure theory. The electronic structure is modeled with density-functional theory (DFT) and is fully relativistic, including the spin-orbit interaction. Furthermore, the DFT is extended to account for orbital–orbital interactions, by means of a parameter-free orbital-polarization (OP) technique, that has proven to be essential for the 5f electrons in plutonium. Strong anharmonicity and the temperature dependence of the lattice vibrations are captured with the self-consistent ab initio lattice dynamics (SCAILD) method. The calculated free energies and heat capacities are compared to published results from quasi-harmonic (QH) theory, and experiments, where available. For the uranium and plutonium compounds, we make use of CALPHAD assessments to help evaluate the theory. Generally, our anharmonic relativistic approach compares well with both CALPHAD and experiments. For the thorium compounds, our theory is in good accord with QH modeling of the free energy at lower temperatures but for the heat capacity the comparison is less favorable.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Mechanical and Thermal Properties for Uranium and U–6Nb Alloy from First-Principles Theory

Elasticity, lattice dynamics, and thermal expansion for uranium and U–6Nb alloy (elastic moduli) are calculated from density functional theory that is extended to include orbital polarization (DFT+OP). Introducing 12.5 at.% of niobium, substitutionally, in uranium softens all the cii elastic moduli, resulting in a significantly softer shear modulus (G). Combined with a nearly invariant bulk modulus (B), the quotient B/G increases dramatically for U–6Nb, suggesting a more ductile material. Lattice dynamics from a harmonic model coupled with a DFT+OP electronic structure is applied for α uranium, and the obtained phonon density of states compares well with inelastic neutron-scattering measurements. The Debye temperature associated with the lattice dynamics falls within the range of experimentally observed Debye temperatures and it also validates our quasi-harmonic (QH) phonon model. The QH Debye–Grüneisen phonon method is combined with a DFT+OP electronic structure and used to explore the anisotropic thermal expansion in α uranium. The anomalous negative thermal expansion (contraction) of the b lattice parameter of the α-phase orthorhombic cell is relatively well reproduced from a free-energy model consisting of QH-phonon and DFT+OP electronic structure contributions.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Thermodynamics of Plutonium Monocarbide from Anharmonic and Relativistic Theory

Thermodynamics of plutonium monocarbide is studied from first-principles theory that includes relativistic electronic structure and anharmonic lattice vibrations. Density-functional theory (DFT) is expanded to include orbital-orbital coupling in addition to the relativistic spin-orbit interaction for the electronic structure and it is combined with anharmonic, temperature dependent, lattice dynamics derived from the self-consistent ab initio lattice dynamics (SCAILD) method. The obtained thermodynamics are compared to results from simpler quasi-harmonic theory and experimental data. Formation enthalpy, specific heat, and Gibbs energy calculated from the anharmonic model are validated by direct comparison with a calculation of phase diagram (CALPHAD) assessment of PuC and sub-stochiometric PuC0.896. Overall, the theory reproduces CALPHAD results and measured data for PuC rather well, but the comparison is hampered by the sub-stoichiometric nature of plutonium monocarbide. It was found that a bare theoretical approach that ignores spin-orbit and orbital-orbital coupling (orbital polarization) of the plutonium 5f electrons promotes too soft phonons and Gibbs energies that are incompatible with that of the CALPHAD assessment of the experimental data. The investigation of PuC suggests that the electronic structure is accurately described by plutonium 5f electrons as “band like” and delocalized, but correlate through spin polarization, orbital polarization, and spin-orbit coupling, in analogy to previous findings for plutonium metal.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Thermodynamics and Magnetism of YCo5 Compound Doped with Fe and Ni: An Ab Initio Study

YCo5 permanent magnet exhibits high uniaxial magnetocrystalline anisotropy energy and has a high Curie temperature. These are good properties for a permanent magnet, but YCo5 has a low energy product, which is notably insufficient for a permanent magnet. In order to improve the energy product in YCo5, we suggest replacing cobalt with iron, which has a much bigger magnetic moment. With a combination of density-functional-theory calculations and thermodynamic CALculation of PHAse Diagrams (CALPHAD) modeling, we show that a new magnet, YFe3(Ni1-xCox)2, is thermodynamically stable and exhibits an improved energy product without significant detrimental effects on the magnetocrystalline anisotropy energy or the Curie temperature.

anisotropy↗
DOE OSTI2020

Thermodynamics of Uranium Tri-Iodide from Density-Functional Theory

Density-functional theory (DFT) is employed to investigate the thermodynamic and ground-state properties of bulk uranium tri-iodide, UI3. The theory is fully relativistic and electron correlations, beyond the DFT and generalized gradient approximation, are addressed with orbital polarization. The electronic structure indicates anti-ferromagnetism, in agreement with neutron diffraction, with band gaps and a non-metallic system. Furthermore, the formation energy, atomic volume, crystal structure, and heat capacity are calculated in reasonable agreement with experiments, whereas for the elastic constants experimental data are unavailable for comparison. The thermodynamical properties are modeled within a quasi-harmonic approximation and the heat capacity and Gibbs free energy as functions of temperature agree with available calculation of phase diagram (CALPHAD) thermodynamic assessment of the experimental data.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Phase Stability in U-6Nb Alloy Doped with Ti from the First Principles Theory

First-principles calculations within the density-functional-theory (DFT) approach are conducted in order to explore and explain the effect of small amounts of titanium on phase stability in the U-6Nb alloy. During rapid quenching from high to room temperature, metastable phases α' (orthorhombic), α" (monoclinic), and γ 0 (tetragonal) can form, depending on Nb concentration. Important mechanical properties depend on the crystal structure and, therefore, an understanding of the effect of impurities on phase stability is essential. Insights on this issue are obtained from quantum-mechanical DFT calculations. The DFT framework does not rely on any material-specific assumptions and is therefore ideal for an unbiased investigation of the U-Nb system.

36 MATERIALS SCIENCE↗