Search NASA⌕ Search

Engineering topics

Sachdev, Anil K.

Publications and source records attributed to Sachdev, Anil K..

System and method of making a crankshaft with alternate materials

A crankshaft for an internal combustion engine is provided. The crankshaft comprises at least four main journals aligned on a crankshaft axis of rotation defining a centerline. The crankshaft further comprises at least three pin journals. Each pin journal is disposed about a respective pin journal axis and positioned between the main journals. Each of the pin journals is joined to a pair of crank arms. Each pair of crank arms is joined to a respective main journal. Each of the main journals, pin journals, and crank arms is made of a first metallic material. Each crank arm has an over-molded counterweight metallurgically bonded thereto. Each counterweight is disposed opposite a respective pin journal relative to the centerline for balance and stability. Each counterweight is made of a second metallic material. The crankshaft has a weight ratio of the second metallic material to the first metallic material of between 0.20 to 0.50.

Klemstine, David C.↗

Increasing the composition range of a novel τ 11 -Al 4 Fe 1.7 Si alloy with additions of Mn

Automotive applications need low-cost, lightweight, high-temperature alloys to increase vehicle efficiency. The Al–Fe–Si system provides an opportunity to develop such a material, as it consists of three low-cost elements that are all abundant in nature. Specifically, the τ 11 -Al 4 Fe 1.7 Si ternary intermetallic phase is a high-temperature, lightweight phase with high strength and good corrosion resistance. However, this phase exhibits a narrow compositional range of stability, resulting in undesirable microstructures forming during solidification and processing, limiting its use in potential applications. Density functional theory (DFT) calculations and a thermodynamically-driven experimental approach utilizing diffusion couples were employed to study the effect of Mn on the stability and composition range of τ 11 -Al 4 Fe 1.7 Si. The DFT calculations showed a decrease in the energy of the structure when alloying with Mn. Experimental results confirmed the predictions from the DFT calculations, indicating that alloying with Mn increases the compositional range, and thus the processability of this phase. New phase diagrams and equilibria are proposed by exploring and determining phase boundaries for the τ 11 -Al 4 Fe 1.7 Si phase with Mn.

36 MATERIALS SCIENCE↗

In situ synchrotron X-ray imaging of 4140 steel laser powder bed fusion

In this study, an in situ synchrotron X-ray imaging technique was used to examine laser powder bed fusion (LPBF) of a chrome-molybedum, AISI 4140, ferrite–bainite steel, from a moving laser source. Since 4140 has received only minimal attention in the AM literature, focus here was on the effects of melt pool dynamics, vapor cavity depths, build layer height, and the origin of porosity on the 4140 as-built microstructure. Four build parameter sets, which enabled variation of laser power, scan speed, laser spot size, and specific energy density (SED), were applied. Vapor cavity and melt pool depths were measured for each single-track laser scan. Direct imaging of the LPBF process demonstrated that the primary source of porosity in the build originates from incorporation of entrapped gas within the powder irrespective of build parameter set. High resolution SEM and EBSD demonstrated that the as-built microstructure did not vary significantly with build parameter set over a broad range of SED. The fast solidification rates observed (0.06–0.08 m/s) lead to fine martensite packet/block size distributions (1–3 µm) with the potential for increased material strength.

36 MATERIALS SCIENCE↗

Combined Synchrotron X-ray Diffraction and Digital Image Correlation Technique for Measurement of Austenite Transformation with Strain in TRIP-assisted Steels

The strain-induced, diffusionless shear transformation of retained austenite to martensite during straining of transformation induced plasticity (TRIP) assisted steels increases strain hardening and delays necking and fracture leading to exceptional ductility and strength, which are attractive for automotive applications. A novel technique that provides the retained austenite volume fraction variation with strain in TRIP-assisted steels with improved precision is presented. Digital images of the gauge section of tensile specimens were first recorded up to selected plastic strains with a stereo digital image correlation (DIC) system. The austenite volume fraction was measured by synchrotron X-ray diffraction from small squares cut from the gage section. Strain fields in the squares were then computed by localizing the strain measurement to the corresponding region of a given square during DIC post-processing of the images recorded during tensile testing. Results obtained for a QP980 steel are used to study the influence of initial volume fraction of austenite and the austenite transformation with strain on tensile mechanical behavior.

Atom Probe Analysis↗

Integrated Computational Materials Engineering (ICME) for Third Generation Advanced High-Strength Steel Development

This paper presents an overview of a four-year project focused on development of an integrated computational materials engineering (ICME) toolset for third generation advanced high-strength steels (3GAHSS). Following a brief look at ICME as an emerging discipline within the Materials Genome Initiative, technical tasks in the ICME project will be discussed. Specific aims of the individual tasks are multi-scale, microstructure-based material model development using state-of-the-art computational and experimental techniques, forming, toolset assembly, design optimization, integration and technical cost modeling. The integrated approach is initially illustrated using a 980 grade transformation induced plasticity (TRIP) steel, subject to a two-step quenching and partitioning (Q&P) heat treatment, as an example.

Savic, Vesna↗