Engineering topics

Sacksteder, K. R.

Publications and source records attributed to Sacksteder, K. R..

9 records

NASA NTRS2011

Analysis of Solar-Heated Thermal Wadis to Support Extended-Duration Lunar Exploration

The realization of the renewed exploration of the Moon presents many technical challenges; among them is the survival of lunar-surface assets during periods of darkness when the lunar environment is very cold. Thermal wadis are engineered sources of stored solar energy using modified lunar regolith as a thermal storage mass that can supply energy to protect lightweight robotic rovers or other assets during the lunar night. This paper describes an analysis of the performance of thermal wadis based on the known solar illumination of the Moon and estimates of producible thermal properties of modified lunar regolith. Analysis has been performed for the lunar equatorial region and for a potential outpost location near the Lunar South Pole. The calculations indicate that thermal wadis can provide the desired thermal energy and temperature control for the survival of rovers or other equipment during periods of darkness.

Balasubramaniam, R.↗

NASA NTRS2010

An Extension of Analysis of Solar-Heated Thermal Wadis to Support Extended-Duration Lunar Exploration

The realization of the renewed exploration of the Moon presents many technical challenges; among them is the survival of lunar surface assets during periods of darkness when the lunar environment is very cold. Thermal wadis are engineered sources of stored solar energy using modified lunar regolith as a thermal storage mass that can supply energy to protect lightweight robotic rovers or other assets during the lunar night. This paper describes an extension of an earlier analysis of performance of thermal wadis based on the known solar illumination of the Moon and estimates of producible thermal properties of modified lunar regolith. The current analysis has been performed for the lunar equatorial region and validates the formerly used 1-D model by comparison of predictions to those obtained from 2-D and 3-D computations. It includes the effects of a thin dust layer covering the surface of the wadi, and incorporating either water as a phase-change material or aluminum stakes as a high thermal conductivity material into the regolith. The calculations indicate that thermal wadis can provide the desired thermal energy and temperature control for the survival of rovers or other equipment during periods of darkness.

Balasubramaniam, R.↗

NASA NTRS2010

Analysis of Solar-Heated Thermal Wadis to Support Extended-Duration Lunar Exploration

The realization of the renewed exploration of the Moon presents many technical challenges; among them is the survival of lunar surface assets during periods of darkness when the lunar environment is very cold. Thermal wadis are engineered sources of stored solar energy using modified lunar regolith as a thermal storage mass that can enable the operation of lightweight robotic rovers or other assets in cold, dark environments without incurring potential mass, cost, and risk penalties associated with various onboard sources of thermal energy. Thermal wadi-assisted lunar rovers can conduct a variety of long-duration missions including exploration site surveys; teleoperated, crew-directed, or autonomous scientific expeditions; and logistics support for crewed exploration. This paper describes a thermal analysis of thermal wadi performance based on the known solar illumination of the moon and estimates of producible thermal properties of modified lunar regolith. Analysis was performed for the lunar equatorial region and for a potential Outpost location near the lunar south pole. The results are presented in some detail in the paper and indicate that thermal wadis can provide the desired thermal energy reserve, with significant margin, for the survival of rovers or other equipment during periods of darkness.

Balasubramaniam, R.↗

NASA NTRS2001

Upward Flame Spread Over Thin Solids in Partial Gravity

The effects of partial-gravity, reduced pressure, and sample width on upward flame spread over a thin cellulose fuel were studied experimentally and the results were compared to a numerical flame spread simulation. Fuel samples 1-cm, 2-cm, and 4-cm wide were burned in air at reduced pressures of 0.2 to 0.4 atmospheres in simulated gravity environments of 0.1-G, 0.16-G (Lunar), and 0.38-G (Martian) onboard the NASA KC-135 aircraft and in normal-gravity tests. Observed steady flame propagation speeds and pyrolysis lengths were approximately proportional to the gravity level. Flames spread more quickly and were longer with the wider samples and the variations with gravity and pressure increased with sample width. A numerical simulation of upward flame spread was developed including three-dimensional Navier-Stokes equations, one-step Arrhenius kinetics for the gas phase flame and for the solid surface decomposition, and a fuel-surface radiative loss. The model provides detailed structure of flame temperatures, the flow field interactions with the flame, and the solid fuel mass disappearance. The simulation agrees with experimental flame spread rates and their dependence on gravity level but predicts a wider flammable region than found by experiment. Some unique three-dimensional flame features are demonstrated in the model results.

Feier, I. I.↗

NASA NTRS1994

Flame spreading over a thin solid in low-speed concurrent flow- Drop tower experimental results and comparison with theory

Flame spread over thin paper samples in low-speed concurrent flow is experimentally investigated in a 5.18 s drop tower. In the experiment, the oxygen molar percentage is varied from 30% down to the flame extinction limits and the forced flow velocity from 5.29 cm/s down to the quenching limits. Motion pictures are taken to observe flame shape, color, size, and spread rates. These quantities are compared with a theoretical model describing concurrent flame spread over thin solids in low-speed flows. The paper also discusses the similarity and difference between concurrent-flow and opposed-flow flame spread in microgravity and between low-speed and high-speed concurrent-flow flame spread. Finally the limitations of using a drop tower for flame spread research is assessed.

Grayson, G. D.↗

NASA NTRS1989

The solid surface combustion space shuttle experiment hardware description and ground-based test results

The Lewis Research Center is developing a series of microgravity combustion experiments for the Space Shuttle. The Solid Surface Combustion Experiment (SSCE) is the first to be completed. SSCE will study flame spreading over thermally thin fuels (ashless filter paper) under microgravity conditions. The flight hardware consists of a combustion chamber containing the sample and a computer which takes the data and controls the experiment. Experimental data will include gas-phase and solid-phase temperature measurements and motion pictures of the combustion process. Flame spread rates will be determined from the motion pictures.

Vento, D. M.↗

NASA NTRS1989

The solid surface combustion Space Shuttle experiment hardware description and ground-based test results

Vento, D. M.↗

NASA NTRS1989

The Modular Combustion Facility for the Space Station Laboratory - A Requirements and Capabilities Study

This paper describes a modular combustion facility for the Space Station, designed to provide facility-level services to interchangeable experiment modules, each of which designed specifically for the needs of a particular combustion experiment. The facility-level services are to include computer devices for the data acquisition, experimental control, and data reduction and analysis; the electrical power conversion and control; video cameras and recordings; the cooling-loop supply; waste management; gas supply; precision gas-mixing; and the combustion diagnostics support. Summarized categories of the data base are provided, which were developed to assimilate and to process the responses from the investigators.

Sacksteder, K. R.↗

NASA NTRS1988

Facilities for microgravity combustion research

The microgravity test facilities at NASA Lewis Research Center are discussed. Low gravity combustion test apparatus and experiments are examined including the study of solid surface combustion and droplet combustion. Plans for the Space Station capability and the Modular Combustion Facility are described.

Sacksteder, K. R.↗