Bricks and Cans for Thermal Storage
Water-filled cans and bricks provide efficient thermal storage for solar space and hot-water heating. Tests indicate thermal storage mediums suitable in both passive and active solar heating systems.
Saha, H.↗
Engineering topics
Saha, H.
Publications and source records attributed to Saha, H..
Parametric study of thermal storage containing rocks or fluid filled cans for solar heating and cooling, phase 2
The test data and an analysis of the heat transfer characteristics of a solar thermal energy storage bed utilizing water filled cans and standard bricks as energy storage medium are presented. This experimental investigation was initiated to find a usable heat intensive solar thermal storage device other than rock storage and water tank. Four different sizes of soup cans were stacked in a chamber in three different arrangements-vertical, horizontal, and random. Air is used as transfer medium for charging and discharge modes at three different mass flow rates and inlet air temperature respectively. These results are analyzed and compared, which show that a vertical stacking and medium size cans with Length/Diameter (L/D) ratio close to one have better average characteristics of heat transfer and pressure drop.
Saha, H.↗
Advanced solar thermal storage medium test data and analysis
A comparative study has been made of experimentally obtained heat transfer and heat storage characteristics of a solar thermal energy storage bed utilizing containerized water or phase change material (PCM) and rock or brick. It is shown that (1) containers with an L/D ratio of 0.80 and a mass/surface area ratio of 2.74 in a random stacking arrangement have the optimum heat transfer characteristics; and (2) vertical stacking has the least pressure drop across the test bed. It is also found that standard bricks with appropriate holes make an excellent storage medium.
Saha, H.↗
Solar energy storage via liquid filled cans - Test data and analysis
This paper describes the design of a solar thermal storage test facility with water-filled metal cans as heat storage medium and also presents some preliminary tests results and analysis. This combination of solid and liquid mediums shows unique heat transfer and heat contents characteristics and will be well suited for use with solar air systems for space and hot water heating. The trends of the test results acquired thus far are representative of the test bed characteristics while operating in the various modes.
Saha, H.↗
Parametric study of rock pile thermal storage for solar heating and cooling phase 1
The test data and an analysis were presented, of heat transfer characteristics of a solar thermal energy storage bed utilizing water filled cans as the energy storage medium. An attempt was made to optimize can size, can arrangement, and bed flow rates by experimental and analytical means. Liquid filled cans, as storage media, utilize benefits of both solids like rocks, and liquids like water. It was found that this combination of solid and liquid media shows unique heat transfer and heat content characteristics and is well suited for use with solar air systems for space and hot water heating. An extensive parametric study was made of heat transfer characteristics of rocks, of other solids, and of solid containers filled with liquids.
Saha, H.↗
Rocket engine thrust chamber wall temperature distribution calculation and analysis
An analytical computational concept is presented which predicts the temperature profiles along a regeneratively cooled thrust chamber wall on the hot gas side and on the coolant side, and also the coolant bulk temperature profile. The computational model is based upon a coupling of the boundary layer heat transfer process with the heat transfer process through the chamber wall and the coolant flow heat absorption. The calculation is started with approximate temperature distributions for the hot gas side wall and the coolant flow. The iteration process of the computer program is terminated when the total heat transfer rates from the hot gas boundary layer to the wall and from the wall to the coolant are equal. The computer program for the integration of regenerative cooling process to a thrust chamber is kept general such that this program can be used with any boundary layer analysis computer program for temperature profile and heat transfer studies. A sample application of this concept is shown by using a boundary layer analysis program for the RL10 rocket engine thrust chamber.
Saha, H.↗
Rocket engine thrust chamber heat transfer calculation and analysis
A parametric study of the heat transfer rate along the wall of a rocket nozzle is presented. The influences of different parameters; laminar and turbulent Lewis number, mixture ratio, initial wall temperature distribution, and eddy viscosity, were considered. The numerical evaluation of these influences on heat transfer rate was done by using three different compressible, reacting laminar and turbulent boundary layer computer programs; MABL (Mass Addition Boundary Layer Program), MABL-KE (MABL program is modified to include turbulent kinetic energy equation), and BLIMP (Boundary Layer Integral Matrix Procedure). This study also provided an excellent opportunity to evaluate the efficiencies of these three computer programs and to suggest one of them for future computational purposes.
Saha, H.↗