Search NASA⌕ Search

Engineering topics

Sakamoto, K.

Publications and source records attributed to Sakamoto, K..

At least 19 records

Liquid metal compatibility of pre-oxidized FeCrAl in flowing Sn

Here, a flowing Sn thermal convection loop (TCL) experiment was conducted in FeCrAlMo (Kanthal alloy APMT) tubing for 1000 h with a peak temperature of 400 °C. Oxide dispersion strengthened (ODS) Fe-(10–12)Cr-6Al and APMT specimens were exposed and all were pre-oxidized to form an external alumina scale. Unlike static exposures at 400° and 500 °C where pre-oxidation prevented dissolution, large mass losses were observed in the TCL hot leg after the specimens were cleaned in Li. The observed pitting suggests that localized failure of the pre-formed alumina surface oxide caused significant metal loss. Specimen mass gains were not observed on the cold leg implying that mass transfer did not occur and the small levels of Fe and Cr in the Sn after the experiment implies that Sn-rich phases may have formed. Post exposure room temperature tensile testing showed limited impact of the Sn exposure on the 12Cr ODS FeCrAl alloy, comparable to a 1000 h anneal in Ar at 400 °C. These results suggest that pre-oxidation is not sufficient to protect FeCrAl alloys in contact with flowing liquid Sn at 350°-400 °C.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Interaction between clay minerals and organics in asteroid Ryugu

The Hayabusa 2 spacecraft brought back to Earth grains of the carbonaceous asteroid Ryugu. Such grains represent the pristine state of CI chondritic materials and have been preserved from exposure to Earth’s atmosphere. Here, we show evidence of the presence of organics trapped within the interlayer space of smectite layers in Ryugu grains. No such organics are found in the Orgueil CI meteorite. We put forward that the organics within the interlayer space of smectite in Orgueil CI meteorite were lost during their oxidation on Earth. Also, we propose that the presence of organics within the interlayers space of smectite might be responsible for the possible NH infrared signature observed in Ryugu particles and potentially to a few large C-type asteroids including Ceres

58 GEOSCIENCES↗

The Solar System calcium isotopic composition inferred from Ryugu samples

The Hayabusa2 spacecraft has returned samples from the Cb-type asteroid (162173) Ryugu to Earth. Previous petrological and chemical analyses support a close link between Ryugu and CI chondrites that are presumed to be chemically the most primitive meteorites with a solar-like composition. However, Ryugu samples are highly enriched in Ca compared to typical CI chondrites. To identify the cause of this discrepancy, here we report stable Ca isotopic data (expressed as δ 44/40 Ca SRM915a ) for returned Ryugu samples collected from two sites. We found that samples from both sites have similar δ 44/40 Ca SRM915a (0.58 ± 0.03 ‰ and 0.55 ± 0.08 ‰, 2 s.d.) that fall within the range defined by CIs. This isotopic similarity suggests that the Ca budget of CIs and Ryugu samples is dominated by carbonates, and the variably higher Ca contents in Ryugu samples are due to the abundant carbonates. Precipitation of carbonates on Ryugu likely coincided with a major episode of aqueous activity dated to have occurred ~5 Myr after Solar System formation. Based on the pristine Ryugu samples, the average δ 44/40 Ca SRM915a of the Solar System is defined to be 0.57 ± 0.04 ‰ (2 s.d.).

79 ASTRONOMY AND ASTROPHYSICS↗

Surface states and Rashba-type spin polarization in antiferromagnetic MnBi 2 Te 4 (0001)

The layered van der Waals antiferromagnet MnBi 2 Te 4 has been predicted to combine the band ordering of archetypical topological insulators such as Bi 2 Te 3 with the magnetism of Mn, making this material a viable candidate for the realization of various magnetic topological states. We have systematically investigated the surface electronic structure of MnBi 2 Te 4 (0001) single crystals by use of spin- and angle-resolved photoelectron spectroscopy experiments. In line with theoretical predictions, the results reveal a surface state in the bulk band gap and they provide evidence for the influence of exchange interaction and spin-orbit coupling on the surface electronic structure.

Vidal, R. C.↗

The Dense Molecular Gas and Nuclear Activity in the ULIRG IRAS 13120–5453

We present new Atacama Large Millimeter/submillimeter Array Band 7 (∼340 GHz) observations of the dense gas tracers HCN, HCO{sup +}, and CS in the local, single-nucleus, ultraluminous infrared galaxy IRAS 13120–5453. We find centrally enhanced HCN (4–3) emission, relative to HCO{sup +} (4–3), but do not find evidence for radiative pumping of HCN. Considering the size of the starburst (0.5 kpc) and the estimated supernovae rate of ∼1.2 yr{sup −1}, the high HCN/HCO{sup +} ratio can be explained by an enhanced HCN abundance as a result of mechanical heating by the supernovae, though the active galactic nucleus and winds may also contribute additional mechanical heating. The starburst size implies a high Σ{sub IR} of 4.7 × 10{sup 12} L {sub ⊙} kpc{sup −2}, slightly below predictions of radiation-pressure limited starbursts. The HCN line profile has low-level wings, which we tentatively interpret as evidence for outflowing dense molecular gas. However, the dense molecular outflow seen in the HCN line wings is unlikely to escape the Galaxy and is destined to return to the nucleus and fuel future star formation. We also present modeling of Herschel observations of the H{sub 2}O lines and find a nuclear dust temperature of ∼40 K. IRAS 13120–5453 has a lower dust temperature and Σ{sub IR} than is inferred for the systems termed “compact obscured nuclei (CONs)” (such as Arp 220 and Mrk 231). If IRAS 13120–5453 has undergone a CON phase, we are likely witnessing it at a time when the feedback has already inflated the nuclear ISM and diluted star formation in the starburst/active galactic nucleus core.

79 ASTRONOMY AND ASTROPHYSICS↗

Development of Ce-type FeCrAl-ODS ferritic steel to accident tolerant fuel for BWRs

A Ce-type FeCrAl-ODS ferritic steel has been examined as a candidate Fe-Cr-Al alloy for the fuel cladding in BWRs. The properties examined in this study were the corrosion resistance to coolant water, the resistance to the high temperature steam and the interactions with neighboring materials (UO{sub 2} and B{sub 4}C). For the corrosion test, the specimens were corroded in an autoclave with circulating pure water at 633 K and a pressure of approximately 20 MPa. In addition to the Ce-ODS, MA956 and SS316L alloys were also corroded as reference materials. For the steam oxidation test, the specimens were oxidized in an electric furnace at 1473 K for 100 h and 1573 K for 25 h under wet Ar gas flow. The materials reaction test with B{sub 4}C was carried out at 1573 K and 1673 K for 1 h. The test with UO{sub 2} was performed in a high purity He gas at 1573 K and 1673 K for 1 h. A disk of UO{sub 2} pellet was set on the Ce-ODS specimen and the reaction couple was held in the pure Zr box to prevent a surface oxidation by residual oxidizing gases. The cross sections of reaction couples were observed by an optical microscope (OM) and a secondary electron microscope (SEM) with energy-dispersive spectroscope (EDS) after the materials interaction tests. The results show that the Ce-type FeCrAl-ODS steel has demonstrated a good corrosion resistance to coolant water and high accident tolerances in the oxidation with high temperature steam and in the interactions with neighboring materials. Those favorable properties would imply that the oxide dispersion strengthened (ODS) technology can be a candidate option for further development of accident-tolerant fuels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development of FeCrAl-ODS steels for ATF cladding

As an enhanced accident tolerant fuel (ATF) for LWR at severe accident condition, FeCrAl-ODS ferritic steels have been developed, and their applicability is being studied under the Japanese MEXT program. Alloying design of FeCrAl-ODS ferritic steels has been conducted, focusing on effect of mutual interaction of Cr-Al on oxidation resistance and α'-embrittlement. Effects of co-addition of Zr and excessive oxygen have also been studied to improve high-temperature strength. The ring tensile test of the manufactured claddings showed that tensile strength increases by Zr-addition and Zr-added FeCrAl-ODS steels have the highest strength among the existed steels at entire temperature range from room temperature up to 1000 Celsius degrees. Although Zr-addition sometimes leads to growth of alumina scale by rapid inward diffusion of oxygen through zirconia inside alumina, oxidation rate of Zr-added FeCrAl-ODS steels was successfully reduced to the level of Zr-free specimen by controlling oxygen content to form Y{sub 2}Zr{sub 2}O{sub 7} inside ODS steel matrix. This finding makes possible to improve not only high-temperature strength but also steam oxidation resistance in the Zr-added FeCrAl-ODS steels. (authors)

36 MATERIALS SCIENCE↗

Control blade degradation test under temperature gradient in steam atmosphere

The core of a boiling water reactor (BWR) consists of an array of fuel assemblies with cross-shaped control blades located between these assemblies. The typical control blade consists of a control blade sheath made of 316L-type S.S., a center pole made of 316L-type S.S., and control rods. In order to understand the degradation process of the control blade channel, control blade degradation tests were performed under various atmospheres with a temperature increase condition and in the presence of a temperature gradient. A test device was built. Four carbon heaters are set on both sides at the upper and the middle parts of the test device. The bottom ceramic part of the test device is cooled by water. Heating in the upper region and cooling at the bottom of the test piece give rise to the temperature gradient in the test piece. Temperatures of the test piece are measured by five W-Re type thermocouples placed close to the test piece. Steam carried by the argon gas is supplied from the bottom of the device and flows to the top inside a square carbon muffle in which the test piece is set. Three windows for visual observations are installed, with one located above the furnace and the others located at the back of the furnace. In the steam atmosphere with a steam flow rate of 0.0125 g/s/rod, the control blade, channel box, and fuel rods were degraded, especially at the upper part of the test piece. This result was similar to that observed in the argon atmosphere test. However, the observed degradation was rather different at a higher steam flow rate of 0.0417 g/s/rod. At the upper part of the test piece, only the control blade was degraded preferentially and did not react with the channel box wall. In contrast, the eutectic reaction of the stainless steel/boron carbide melt and zircaloy occurred at the lower part by coexisting with the relocated melt from the top part. These observations suggested the existence of a threshold condition for the control rod degradation between 0.0125 and 0.0417 g/s/rod which is significantly affected by the thickness of the oxide layer on zircaloy.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

SMA OBSERVATIONS OF THE EXTENDED {sup 12}CO(J = 6–5) EMISSION IN THE STARBURST GALAXY NGC 253

We present observations of the {sup 12}CO(J = 6–5) line and 686 GHz continuum emission in NGC 253 with the Submillimeter Array at an angular resolution of ∼4″. The {sup 12}CO(J = 6–5) emission is clearly detected along the disk and follows the distribution of the lower {sup 12}CO line transitions with little variation of the line ratios. A large velocity gradient analysis suggests a two-temperature model of the molecular gas in the disk, likely dominated by a combination of low-velocity shocks and the disk-wide photodissociation regions. Only marginal {sup 12}CO(J = 6–5) emission is detected in the vicinity of the expanding shells at the eastern and western edges of the disk. While the eastern shell contains gas even warmer (T{sub kin} > 300 K) than the hot gas component (T{sub kin} = 300 K) of the disk, the western shell is surrounded by gas much cooler (T{sub kin} = 60 K) than the eastern shell but somewhat hotter than the cold gas component of the disk (for similar H{sub 2} and CO column densities), indicative of different (or differently efficient) heating mechansisms. The continuum emission at 686 GHz in the disk agrees well in shape and size with that at lower (sub)millimeter frequencies, exhibiting a spectral index consistent with thermal dust emission. We find dust temperatures of ∼10–30 K and largely optically thin emission. However, our fits suggest a second (more optically thick) dust component at higher temperatures (T{sub d}>60 K), similar to the molecular gas. We estimate a global dust mass of ∼10{sup 6} M{sub ⊙} for the disk, translating into a gas-to-dust mass ratio of a few hundred, consistent with other nearby active galaxies.

79 ASTRONOMY AND ASTROPHYSICS↗

Transportation of a radioactive ion beam for precise laser-trapping experiments

Francium is the heaviest species among the alkali elements. Due to its properties, francium is said to be of advantage in measurements of tiny observations, such as atomic parity violation and electric dipole moment. Before executing experiments with francium, it must be produced artificially because it is one of the most unstable elements. We produced francium with the nuclear fusion reaction of an oxygen beam and gold target, ionized the produced francium through a thermal ionization process, and extracted the ion with electrostatic fields. However, the thermal ionization process is known to ionize not only an objective atom but also other atomic species. Therefore, a Wien filter was installed to analyze the composition of the ion beam and purify the beam. This allowed us to improve the beam purity from ∼10{sup −6} to ∼10{sup −3}.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Low background techniques in CANDLES

CANDLES is a double beta decay experiment using {sup 48}Ca in CaF{sub 2} crystals. The measurement is being performed with prototype detector (CANDLES III) for high sensitive measurement in the future. Recent status of detector improvements and background reduction techniques are described in this paper.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Demonstration of sawtooth period control with EC waves in KSTAR plasma

The sawtooth period control in tokamak is important issue in recent years because the sawtooth crash can trigger TM/NTM instabilities and drive plasmas unstable. The control of sawtooth period by the modification of local current profile near the q=1 surface using ECCD has been demonstrated in a number of tokamaks [1, 2] including KSTAR. As a result, developing techniques to control the sawtooth period as a way of controlling the onset of NTM has been an important area of research in recent years [3]. In 2012 KSTAR plasma campaign, the sawtooth period control is carried out by the different deposition position of EC waves across the q=1 surface. The sawtooth period is shortened by on-axis co-ECCD (destabilization), and the stabilization of the sawtooth is also observed by off-axis co-ECCD at outside q=1 surface. In 2013 KSTAR plasma campaign, the sawtooth locking experiment with periodic forcing of 170 GHz EC wave is carried out to control the sawtooth period. The optimal target position which lengthens the sawtooth period is investigated by performing a scan of EC beam deposition position nearby q=1 surface at the toroidal magnetic field of 2.9 T and plasma current of 0.7 MA. The sawtooth locking by the modulated EC beam is successfully demonstrated as in [3-5] with the scan of modulation-frequency and duty-ratio at the low beta (β N ~0.5) plasma. In this paper, the sawteeth behavior by the location of EC beam and the preliminary result of the sawtooth locking experiments in KSTAR will be presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

HIGH-RESOLUTION RADIO CONTINUUM MEASUREMENTS OF THE NUCLEAR DISKS OF Arp 220

We present new Karl G. Jansky Very Large Array radio continuum images of the nuclei of Arp 220, the nearest ultra-luminous infrared galaxy. These new images have both the angular resolution to study the detailed morphologies of the two nuclei that power the galaxy merger and sensitivity to a wide range of spatial scales. At 33 GHz, we achieve a resolution of 0.''081 × 0.''063 (29.9 × 23.3 pc) and resolve the radio emission surrounding both nuclei. We conclude from the decomposition of the radio spectral energy distribution that a majority of the 33 GHz emission is synchrotron radiation. The spatial distributions of radio emission in both nuclei are well described by exponential profiles. These have deconvolved half-light radii (R {sub 50d}) of 51 and 35 pc for the eastern and western nuclei, respectively, and they match the number density profile of radio supernovae observed with very long baseline interferometry. This similarity might be due to the fast cooling of cosmic rays electrons caused by the presence of a strong (∼mG) magnetic field in this system. We estimate extremely high molecular gas surface densities of 2.2{sub −1.0}{sup +2.1}×10{sup 5} (east) and 4.5{sub −1.9}{sup +4.5}×10{sup 5} (west) M {sub ☉} pc{sup –2}, corresponding to total hydrogen column densities of N {sub H} = 2.7{sub −1.2}{sup +2.7}×10{sup 25} (east) and 5.6{sub −2.4}{sup +5.5}×10{sup 25} cm{sup –2} (west). The implied gas volume densities are similarly high, n{sub H{sub {sub 2}}}∼3.8{sub −1.6}{sup +3.8}×10{sup 4} (east) and ∼11{sub −4.5}{sup +12}×10{sup 4} cm{sup –3} (west). We also estimate very high luminosity surface densities of Σ{sub IR}∼4.2{sub −0.7}{sup +1.6}×10{sup 13} (east) and Σ{sub IR}∼9.7{sub −2.4}{sup +3.7}×10{sup 13} (west) L{sub ⊙} kpc{sup −2}, and star formation rate surface densities of Σ{sub SFR} ∼ 10{sup 3.7} {sup ±} {sup 0.1} (east) and Σ{sub SFR} ∼ 10{sup 4.1} {sup ±} {sup 0.1}(west) M {sub ☉} yr{sup –1}kpc{sup –2}. These values, especially for the western nucleus are, to our knowledge, the highest luminosity surface densities and star formation rate surface densities measured for any star-forming system. Despite these high values, the nuclei appear to lie below the dusty Eddington limit in which radiation pressure is balanced only by self-gravity. The small measured sizes also imply that at wavelengths shorter than λ = 1 mm, dust absorption effects must play an important role in the observed light distribution while below 5 GHz free-free absorption contributes substantial opacity. According to these calculations, the nuclei of Arp 220 are only transparent in the frequency range ∼5-350 GHz. Our results offer no clear evidence that an active galactic nucleus dominates the emission from either nucleus at 33 GHz.

79 ASTRONOMY AND ASTROPHYSICS↗

Millimeter wave experiment of ITER equatorial EC launcher mock-up

The full-scale mock-up of the equatorial launcher was fabricated in basis of the baseline design to investigate the mm-wave propagation properties of the launcher, the manufacturability, the cooling line management, how to assemble the components and so on. The mock-up consists of one of three mm-wave transmission sets and one of eight waveguide lines can deliver the mm-wave power. The mock-up was connected to the ITER compatible transmission line and the 170GHz gyrotron and the high power experiment was carried out. The measured radiation pattern of the beam at the location of 2.5m away from the EL mock-up shows the successful steering capability of 20°∼40°. It was also revealed that the radiated profile at both steering and fixed focusing mirror agreed with the calculation. The result also suggests that some unwanted modes are included in the radiated beam. Transmission of 0.5MW-0.4sec and of 0.12MW-50sec were also demonstrated.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

High power test of a wideband diplexer with short-slotted metal half mirrors for electron cyclotron current drive system

The wideband high power diplexer has been developed for combining and fast switching of high power millimeter waves generated by a dual frequency gyrotron. The actual diplexer was tested at the frequency band of 170 GHz in low power. After adjusting a resonant frequency of diplexer for the gyrotron frequency, the evacuated wideband diplexer with short-slotted metal half mirrors was tested at an incident power of about 150 kW, a pulse duration of 30 ms and a frequency band of 170.2–170.3 GHz. Any discharge damage was not observed in the diplexer.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Three-Dimensional Shapes and Impactor Size Estimation of Stardust Impact

Impact tracks formed by cometary dust capture in silica aerogel collectors in the Stardust mission [1] have a variety of shapes, showing diversity of the cometary dust [2]. We have investigated 3-D structures and elemental distributions of three impact tracks using synchrotron radiation x-ray analyses (microtomography and XRF) as one of the preliminary examination [3]. In this study, additional five tracks were investigated by the same analytical method. Impactor sizes of the tracks were estimated from the track entrance sizes and Fe abundances. Size parameters, such as length, of the tracks were normalized by the impactor size to compare track shape

Iida, Y.↗

Mineralogy, Three Dimensional Structure, and Oxygen Isotope Ratios of Four Crystalline Particles from Comet 81P/Wild 2

Preliminary examinations of small dust particles from comet 82P/Wild 2 revealed many expected and unexpected features. Among them the most striking feature is the presence of abundant crystalline material in the comet. Synchrotron radiation X-ray diffraction and microtomography are the most efficient methods to detect and describe bulk mineralogical features of crystalline cometary particles. In the present study, in addition to these two non-destructive techniques, electron microscopy and ion-probe mass spectrometry were carried out on the four crystalline particles.

Nakamura, T.↗