Engineering topics

Salikuddin, M.

Publications and source records attributed to Salikuddin, M..

32 records · Page 2

NASA NTRS1984

An experimental study of tone excited heated jets

The objective of this investigation was to obtain detailed experimental data on the effects of upstream acoustic excitation on the mixing of heated jets with the surrounding air. Based on the information gathered in the literature survey, a technical approach was developed to carry out a systematic set of mean flowfield measurements for a broad range of jet operating and acoustic excitation conditions. Most of the results were obtained at Mach numbers of 0.3 and 0.8 and total temperatures of up to 800 K. Some measurements were made also for the fully expanded supersonic jet of Mj = 1.15. The maximum level of excitation was Le equal to or less than 150 dB and a range of excitation frequencies up to fe = 4 kHz was used. The important results derived from this study can be summarized as follows: (1) the sensitivity of heated jets to upstream acoustic excitation varies strongly with the jet operating conditions, (2) the threshold excitation level increases with increasing jet temperature, and (3) the preferred Strouhal number does not change significantly with a change of the jet operating conditions.

Lepicovsky, J.↗

NASA NTRS1983

Acoustic power dissipation on radiation through duct terminations - Experiments

This paper describes the acoustic transmission characteristics of ducts, nozzles, orifices, and perforated plates, studied under an experimental program using an acoustic impulse technique. In this technique high intensity pulses, generated by discharging a capacitor across a spark gap, were used as the sound source. The test conditions include heated and unheated flows, with and without simulated flight. Results for a straight round duct, three convergent nozzles, a suppressor nozzle, 12 orifice plates, and 10 perforated plates are presented. A low frequency acoustic power loss phenomenon was observed for all configurations at all test conditions including the no flow condition. It was suspected that the power loss phenomenon at the no flow condition could be due to the conversion of acoustic energy into vortical energy due to non-linear propagation of high intensity pulses. However, a small amount of low frequency power loss was noticed even when tests were repeated with a low intensity sound. Detailed flow visualization results were also obtained to complement the acoustic results.

Salikuddin, M.↗

NASA NTRS1983

Sound radiation from annular ducts/nozzles using modal decomposition of in-duct acoustic power

Using a refined acoustic impulse technique, an experimental program was carried out to determine the proper procedure for measuring the acoustic power for both incident and reflected sound fields for annular ducts with and without nozzles at various flow conditions. Several radial and azimuthal pressure measurements were made, and using these complex pressure data, the modal content of the pressure field was determined. A mathematical approach for the modal decomposition of annular duct acoustic power was developed. The acoustic power due to each individual mode and also their total sum were derived. The acoustic characteristics of annular duct-nozzle systems were studied at various flow conditions. The results derived from the experiments include the termination reflection coefficient, the normalized transmission coefficients, the power transfer functions and the power imbalance.

Salikuddin, M.↗

NASA NTRS1983

Refinement and application of acoustic impulse technique to study nozzle transmission characteristics

An improved acoustic impulse technique was developed and was used to study the transmission characteristics of duct/nozzle systems. To accomplish the above objective, various problems associated with the existing spark-discharge impulse technique were first studied. These included (1) the nonlinear behavior of high intensity pulses, (2) the contamination of the signal with flow noise, (3) low signal-to-noise ratio at high exhaust velocities, and (4) the inability to control or shape the signal generated by the source, specially when multiple spark points were used as the source. The first step to resolve these problems was the replacement of the spark-discharge source with electroacoustic driver(s). These included (1) synthesizing on acoustic impulse with acoustic driver(s) to control and shape the output signal, (2) time domain signal averaging to remove flow noise from the contaminated signal, (3) signal editing to remove unwanted portions of the time history, (4) spectral averaging, and (5) numerical smoothing. The acoustic power measurement technique was improved by taking multiple induct measurements and by a modal decomposition process to account for the contribution of higher order modes in the power computation. The improved acoustic impulse technique was then validated by comparing the results derived by an impedance tube method. The mechanism of acoustic power loss, that occurs when sound is transmitted through nozzle terminations, was investigated. Finally, the refined impulse technique was applied to obtain more accurate results for the acoustic transmission characteristics of a conical nozzle and a multi-lobe multi-tube supressor nozzle.

Salikuddin, M.↗

NASA NTRS1982

Generation of desired signals from acoustic drivers

A procedure to control transient signal generation is developed for the study of internal noise propagation from aircraft engines. A simple algorithm incorporating transform techniques is used to produce signals of any desired waveform from acoustic drivers. The accurate driver response is then calculated, and from this the limiting frequency characteristics are determined and the undesirable frequencies where the driver response is poor are eliminated from the analysis. A synthesized signal is then produced by convolving the inverse of the response function with the desired signal. Although the shape of the synthesized signal is in general quite awkward, the driver generates the desired signal when the distorted signal is fed into the driver. The results of operating the driver in two environments, in a free field and in a duct, are presented in order to show the impedance matching effect of the driver. In addition, results using a high frequency cut-off value as a parameter is presented in order to demonstrate the extent of the applicability of the synthesis procedure. It is concluded that the desired signals can be generated through the signal synthesis procedure.

Ramakrishnan, R.↗

NASA NTRS1981

A unique method to study acoustic transmission through ducts using signal synthesis and averaging of acoustic pulses

An acoustic impulse technique using a loudspeaker driver is developed to measure the acoustic properties of a duct/nozzle system. A signal synthesis method is used to generate a desired single pulse with a flat spectrum. The convolution of the desired signal and the inverse Fourier transform of the reciprocal of the driver's response are then fed to the driver. A signal averaging process eliminates the jet mixing noise from the mixture of jet noise and the internal noise, thereby allowing very low intensity signals to be measured accurately, even for high velocity jets. A theoretical analysis is carried out to predict the incident sound field; this is used to help determine the number and locations of the induct measurement points to account for the contributions due to higher order modes present in the incident tube method. The impulse technique is validated by comparing experimentally determined acoustic characteristics of a duct-nozzle system with similar results obtained by the impedance tube method. Absolute agreement in the comparisons was poor, but the overall shapes of the time histories and spectral distributions were much alike.

Salikuddin, M.↗

NASA NTRS1981

Acoustic power dissipation on radiation through duct terminations - Experiments

An acoustic impulse technique is used to study the acoustic transmission characteristics of ducts, nozzles, orifices, and perforated plates. High intensity pulses were generated by discharging a capacitor across a spark gap for both heated and unheated flows, with and without simulated flights. The effect of a termination geometry on power absorption for high acoustic intensities was observed, showing the existence of power absorption at low frequencies for the duct, nozzles, orifice plates, and perforated plates at a no flow condition; the amount of power absorption was controlled primarily by the open area at the exit. Power conservation with flow was similar to that for no flow: Power absorption initially increased for the duct and conical nozzles and then decreased with increasing Mach number. Power absorption results for the suppressor nozzle were similar to those for the conical nozzle, and the nonlinear effect was found to be insignificant in the presence of flow. A power imbalance was noted for heated jets, with a greater power loss at low frequencies than for unheated jets. Low frequency power absorption increased with the simulated flight, and a small amount of low frequency power absorption was found even for low intensity sound. A typical schlieren photograph of vortex formation (Whiffen and Ahuja, 1981) helped to confirm that sound energy can be converted into vortical energy and may account for low frequency power losses.

Salikuddin, M.↗

NASA NTRS1980

Measuring acoustic properties of materials and jet nozzles

Method measures acoustic properties of sound-absorbent materials and jet-nozzle system. Advantages of impulse method over other methods are that test time and complication are reduced. Results obtained from impulse method have been compared with those from existing methods, both experimental and theoretical, and show excellent agreement.

Dean, P. D.↗

NASA NTRS1980

A study of the transmission characteristics of suppressor nozzles

The internal noise radiation characteristics for a single stream 12 lobe 24 tube suppressor nozzle, and for a dual stream 36 chute suppressor nozzle were investigated. An equivalent single round conical nozzle and an equivalent coannular nozzle system were also tested to provide a reference for the two suppressors. The technique utilized a high voltage spark discharge as a noise source within the test duct which permitted separation of the incident, reflected and transmitted signals in the time domain. These signals were then Fourier transformed to obtain the nozzle transmission coefficient and the power transfer function. These transmission parameters for the 12 lobe, 24 tube suppressor nozzle and the reference conical nozzle are presented as a function of jet Mach number, duct Mach number polar angle and temperature. Effects of simulated forward flight are also considered for this nozzle. For the dual stream, 36 chute suppressor, the transmission parameters are presented as a function of velocity ratios and temperature ratios. Possible data for the equivalent coaxial nozzle is also presented. Jet noise suppression by these nozzles is also discussed.

Ahuja, K. K.↗

NASA NTRS1980

Low frequency sound absorption of orifice plates, perforated plates and nozzles

Analyses of impulse time history data from acoustic transmission tests for conical nozzles attached to a pipe show internal reflections from the solid contraction and open area tend to cancel. To gain understanding of the opposing reflections, tests were conducted by replacing the conical nozzles with orifice plates. The primary variable was the open to solid area ratio. Internal reflection coefficient data reveal that, at an area ratio of 10-12%, the low frequency internal reflection is reduced from unity to about 0.2. Based on comparisons of far-field and internal data, acoustic energy is not conserved. Results are presented for complex reflection coefficient and far-field noise for a series of orifice and perforated plate configurations.

Salikuddin, M.↗

NASA NTRS1980

Characteristics of internal- and jet-noise radiation from a multi-lobe, multi-tube suppressor nozzle tested statically and under flight simulation

Nozzle transmission coefficient (NTC) for a 12-lobe, 24-tube suppressor nozzle and a reference round convergent nozzle of equal area are obtained by an impulse test technique. This technique utilizes a high voltage spark discharge as a noise source within the test duct. Effects of nozzle geometry, jet Mach number, jet temperature and flight velocity on the radiation characteristics of the two nozzles are presented. Likewise, the jet mixing noise measured in the absence of internal noise for both nozzles at static and also simulated flight conditions are discussed.

Ahuja, K. K.↗

NASA NTRS1979

Studies of the acoustic transmission characteristics of coaxial nozzles with inverted velocity profiles: Comprehensive data report

The efficiency of internal noise radiation through a coannular exhaust nozzle with an inverted velocity profile was studied. A preliminary investigation was first undertaken (1) to define the test parameters which influence the internal noise radiation; (2) to develop a test methodology which could realistically be used to examine the effects of the test parameters; and (3) to validate this methodology. The result was the choice of an acoustic impulse as the internal noise source in the jet nozzles. Noise transmission characteristics of a coannular nozzle system were then investigated. In particular, the effects of fan convergence angle, core extension length to annulus height ratio and flow Mach numbers and temperatures were studied. Relevant spectral data only is presented in the form of normalized nozzle transfer function versus nondimensional frequency.

Dean, P. D.↗

NASA NTRS1979

Studies of the acoustic transmission characteristics of coaxial nozzles with inverted velocity profiles, volume 1

The efficiency of internal noise radiation through coannular exhaust nozzle with an inverted velocity profile was studied. A preliminary investigation was first undertaken to: (1) define the test parameters which influence the internal noise radiation; (2) develop a test methodology which could realistically be used to examine the effects of the test parameters; (3) and to validate this methodology. The result was the choice of an acoustic impulse as the internal noise source in the in the jet nozzles. Noise transmission characteristics of a nozzle system were then investigated. In particular, the effects of fan nozzle convergence angle, core extention length to annulus height ratio, and flow Mach number and temperatures were studied. The results are presented as normalized directivity plots.

Dean, P. D.↗

NASA NTRS1979

An impulse test technique with application to acoustic measurements

A method has been presented for measuring the acoustic properties of an absorbent material and a duct/nozzle system (with or without airflow) using a high voltage spark discharge as an impulse source of sound. The cross-spectra of the incident, reflected and transmitted acoustic pressure transients are analyzed by way of a FFT digital processor in the form of complex transfer functions. These transfer functions have a direct relationship to the termination impedance and radiation directivity. The impulse method has been justified by comparisons, with data obtained from existing methods (both experimental and theoretical), that show excellent agreement. Reflection coefficients and radiation impedances of various duct-nozzle systems and their associated far-field directivities are also presented as some of the applications of the impulse technique.

Salikuddin, M.↗