Velocimeter LIDAR Based Bulk Velocity Estimation for Terrain Relative Navigation Applications
No abstract provided
Skulsky, Eli↗
Engineering topics
San Martin, Alejandro
Publications and source records attributed to San Martin, Alejandro.
Velocimeter LIDAR Based Bulk Velocity Estimation for Terrain Relative Navigation Applications
A novel batch state estimation approach to estimate the translational and angular velocity states of a vehicle using a state-of-the-art velocimeter Light Detection and Ranging (LIDAR) sensor for use in Terrain and Hazard Relative Navigation (TRN/HRN) applications is presented in this paper. The velocimeter LIDAR is capable of measuring three dimensional position and line-of-sight (LOS) velocity associated with every pixel in the field-of-view (FOV). This new batch state estimation methodology is shown to provide accurate and statistically consistent velocity estimates with no a priori information. In contrast to traditional computer vision approaches for TRN, the proposed technique is not dependent on image features. This feature alleviates the need for accurate feature detection and correspondence to a predefined map making it suitable for unknown operating environments. Following a detailed development of the mathematical details associated with the batch state estimation methodology, the efficacy and utility of the proposed algorithms are evaluated through emulation robotics experiments performed at Texas A&M’s Land, Air, and Space Robotics (LASR) laboratory.
Skulsky, Eli↗
System Verification of MSL Skycrane Using an Integrated ADAMS Simulation
Mars Science Laboratory (MSL) will use the Skycrane architecture to execute final descent and landing maneuvers. The Skycrane phase uses closed-loop feedback control throughout the entire phase, starting with rover separation, through mobility deploy, and through touchdown, ending only when the bridles have completely slacked. The integrated ADAMS simulation described in this paper couples complex dynamical models created by the mechanical subsystem with actual GNC flight software algorithms that have been compiled and linked into ADAMS. These integrated simulations provide the project with the best means to verify key Skycrane requirements which have a tightly coupled GNC-Mechanical aspect to them. It also provides the best opportunity to validate the design of the algorithm that determines when to cut the bridles. The results of the simulations show the excellent performance of the Skycrane system.
White, Christopher↗
Coherent Laser Instrument Would Measure Range and Velocity
A proposed instrument would project a narrow laser beam that would be frequency-modulated with a pseudorandom noise (PN) code for simultaneous measurement of range and velocity along the beam. The instrument performs these functions in a low mass, power, and volume package using a novel combination of established techniques. Originally intended as a low resource- footprint guidance sensor for descent and landing of small spacecraft onto Mars or small bodies (e.g., asteroids), the basic instrument concept also lends itself well to a similar application guiding aircraft (especially, small unmanned aircraft), and to such other applications as ranging of topographical features and measuring velocities of airborne light-scattering particles as wind indicators. Several key features of the instrument s design contribute to its favorable performance and resource-consumption characteristics. A laser beam is intrinsically much narrower (for the same exit aperture telescope or antenna) than a radar beam, eliminating the need to correct for the effect of sloping terrain over the beam width, as is the case with radar. Furthermore, the use of continuous-wave (CW), erbium-doped fiber lasers with excellent spectral purity (narrow line width) permits greater velocity resolution, while reducing the laser s power requirement compared to a more typical pulsed solid-state laser. The use of CW also takes proper advantage of the increased sensitivity of coherent detection, necessary in the first place for direct measurement of velocity using the Doppler effect. However, measuring range with a CW beam requires modulation to "tag" portions of it for time-of-flight determination; typically, the modulation consists of a PN code. A novel element of the instrument s design is the use of frequency modulation (FM) to accomplish both the PN-modulation and the Doppler-bias frequency shift necessary for signed velocity measurements. This permits the use of a single low-power waveguide electrooptic phase modulator, while simultaneously mitigating the effects of speckle as a noise source in the coherent detection.
Chang, Daniel↗
Lidar for Guidance of a Spacecraft or Exploratory Robot
A report describes the Laser Mapper (LAMP) -- a lightweight, compact, low-power lidar system under development for guidance of a spacecraft or exploratory robotic vehicle (rover) at Mars or another planet. The LAMP is intended especially for use during rendezvous of two spacecraft in orbit, for mapping terrain during descent and landing of a spacecraft, for capturing a sample that has been launched into orbit, or navigation and avoidance of obstacles by a rover traversing terrain. The LAMP includes a laser that emits high-power, short light pulses. The laser beam is aimed in azimuth and elevation by use of a mirror on a two-axis gimbal, which scans the beam across a field of regard. Light reflected by a target is collected by a telescope, and the distance to the target is determined by measuring the round-trip travel time for reflected light pulses. The distance information is combined with directional information to construct a three-dimensional map of targets in the field of regard.
Liebe, Carl Christian↗