Search NASA⌕ Search

Engineering topics

Sanahuja, Julien

Publications and source records attributed to Sanahuja, Julien.

FFT-based model for irradiated aggregate microstructures in concrete

The concrete biological shield of light water reactors is exposed to neutron and gamma irradiation throughout its lifetime, which results in the long-term degradation of the concrete’s mechanical properties. Under neutron irradiation, the concrete’s aggregates are subjected to radiation-induced volumetric expansion (RIVE), which strongly depends on the mineral content of the aggregate and exhibits the largest expansion in silicate-bearing minerals. In this work, the authors used the fast Fourier transform-based code Microstructure-Oriented Scientific Analysis of Irradiated Concrete (MOSAIC) in 2D to model the expansion of five different aggregates provided by the Japan Concrete Aging Management Program (JCAMP). Comparable rock specimens were irradiated at the JEEP-II test reactor. The model uses realistic aggregate microstructure reconstruction based on high-resolution characterization images. The model accounts for anisotropic RIVE, thermal expansion, and the associated initiation and propagation of damage. The RIVE models are calibrated based on expansion data in the literature. The authors assume that damage occurs exclusively at interfaces between the particles that compose an aggregate and that these interfaces also exhibit swelling. Using a micromechanical model, the evolution of Young’s modulus with RIVE is calculated for each aggregate and compared with Russian irradiation data. The modeled linear expansion agrees well with the experimentally measured expansion. Furthermore, the model also predicts that anisotropic RIVE and thermal expansion result in an earlier onset of damage with neutron fluence than in the isotropic case.

36 MATERIALS SCIENCE↗

Effects of internal swelling on residual elasticity of a quasi-brittle material through a composite sphere model

This work describes the development of a micromechanical-based constitutive model accounting for the effect of internal expansion on the residual elasticity of a Hashin composite material. This material is made of spherical inclusions that are subjected to gradual swelling within a quasi-brittle matrix. The main focus of this work is to describe and analyze the material mechanical response, with an additional focus on the internal swelling’s effect on the stress–strain response and residual elasticity. Microstructural features and parameters of major importance for the mechanical responses were identified. The innovative characteristics of the proposed approach are summarized as follows: (1) a full determination of the physics of a complete-damage problem throughout the whole process of inclusion swelling with upscaling techniques, which transfers the microcrack-related properties from the lower scale to upper scale; and (2) an evolution of the mechanical fields and the corresponding residual elasticity for various inclusion swelling levels. Concerning the matrix–inclusion composite, it was hypothesized that only the matrix was susceptible to cracking, with varied degrees of damage, whereas the inclusions behave elastically and the elastic modulus of the expanding inclusions remains constant. It is to emphasize that the gradual swelling of inclusions is modeled by an increasing strain in the current micromechanical-based constitutive model, and the microcracks are represented by a set of randomly oriented penny-shaped microcracks with identical radii (namely, closed cracks). The main contribution of the current research is to establish the exact mathematical solutions for the mechanical fields (stress, strain) caused by the swelling of the inclusions (mechanical loading) and derive the effective residual elasticity of a composite (structural response) subject to internal expansion and quasi-brittle damage. Based on the assumption of closed cracks that could be extended to open cracks in the upcoming work, the results proposed by the present paper help to understand the non-linear mechanical behavior of quasi-brittle materials subject to microcracking and provide a theoretical framework to be used as academical benchmark for numerical simulations.

36 MATERIALS SCIENCE↗

Irradiation-induced damage in concrete-forming aggregates: revisiting literature data through micromechanics

The radiation-induced volumetric expansion (RIVE) of aggregate-forming minerals causes damage in concrete exposed to high levels of fast neutrons fluence ( \(>\,\sim \,10^{19}\, \hbox {n}\,\hbox {cm}^{-2}\) at kinetics energy above 0.1 MeV). Historical post-irradiation RIVE and Young’s modulus data obtained in test reactors were revisited using a polycrystalline homogenization model (self-consistent scheme) accounting for the aggregates’ minerals content and the formation of voids/cracks during irradiation. It was found that the formation of extra voids/cracks can contribute to the aggregate expansion more substantially than the cumulated expansions of aggregate-forming minerals. Furthermore, the rate of void creation appears to be inversely correlated to the silica content, although aggregates of higher silicate contents exhibit higher RIVEs. The loss of Young’s modulus decreases exponentially with the aggregates’ expansion. At a comparable RIVE level, the relative loss of modulus is more significant in aggregates of higher silica content.

36 MATERIALS SCIENCE↗

A 12 year EDF study of concrete creep under uniaxial and biaxial loading

This paper presents a 12-year-long creep and shrinkage experimental campaign on cylindrical and prismatic concrete samples under uniaxial and biaxial stress, respectively. The motivation for the study is the need for predicting the delayed strains and the pre-stress loss of concrete containment buildings of nuclear power plants. Two subjects are central in this regard: the creep strain's long-term evolution and the creep Poisson's ratio. A greater understanding of these areas is necessary to ensure reliable predictions of the long-term behavior of the concrete containment buildings.Long-term basic creep appears to evolve as a logarithm function of time in the range of 3 to 10 years of testing. Similar trends are observed for drying creep, autogenous shrinkage, and drying shrinkage testing, which suggests that all delayed strains obtained using different loading and drying conditions originate from a common mechanism.The creep Poisson's ratio derived from the biaxial tests is approximately constant over time for both the basic and drying creep tests (creep strains corrected by the shrinkage strain).It is also shown that the biaxial non-drying samples undergo a significant increase in Young's modulus after 10 years.

36 MATERIALS SCIENCE↗

Combined Effects of Temperature and Irradiation on Concrete Damage

Aggregate radiation-induced volumetric expansion (RIVE) is a predominant mechanism in the formation of mechanical damage in the hardened cement paste (hcp) of irradiated concrete under fast-neutron flux (Giorla et al. 2015). Among the operating conditions difference between test reactors and light water reactors (LWRs), the difference of irradiation flux and temperature is significant. While a temperature increase is quite generally associated with a direct, or indirect (e.g., by dehydration) loss of mechanical properties (Maruyama et al. 2014), we found that it causes a partial annealing of irradiation amorphization of α-quartz, hence, reducing RIVE rate. Based on data collected by Bykov et al. (1981), an incremental RIVE model coupling neutron fluence and temperature is developed. The elastic properties and coefficient of thermal expansion (CTE) of irradiated polycrystalline quartz are interpreted through analytical homogenization of experimental data on irradiated α-quartz published by Mayer and Lecomte (1960). Moreover, the proposed model, implemented in the meso-scale simulation code AMIE, is compared to experimental data obtained on ordinary concrete made of quartz/quartzite aggregate (Dubrovskii et al. 1967). Substantial discrepancy, in terms of damage and volumetric expansion developments, is found when comparing irradiation scenarios assuming constant flux and temperature, as opposed to more realistic test reactor operation conditions.

36 MATERIALS SCIENCE↗

Numerical homogenization of concrete microstructures without explicit meshes

Life management of electric hydro or nuclear power plants requires to estimate long-term concrete properties on facilities, for obvious safety and serviceability reasons. Decades-old structures are foreseen to be operational for several more decades. As a large number of different concrete formulations are found in EDF facilities, empirical models based on many experiments cannot be an option for a large fleet of power plant buildings. To build predictive models, homogenization techniques offer an appealing alternative. To properly upscale creep, especially at long term, a rather precise description of the microstructure is required. However, the complexity of the morphology of concrete poses several challenges. In particular, concrete is formulated to maximize the packing density of the granular skeleton, leading to aggregates spanning several length scales with small inter particle spacings. Thus, explicit meshing of realistic concrete microstructures is either out of reach of current meshing algorithms or would produce a number of degrees of freedom far higher than the current generic FEM codes capabilities. This paper proposes a method to deal with complex matrix-inclusions microstructures such as the ones encountered at the mortar or concrete scales, without explicitly meshing them. The microstructure is superimposed to an independent mesh, which is a regular Cartesian grid. This inevitably yields so called 'gray elements', spanning across multiple phases. As the reliability of the estimate of the effective properties highly depends on the behavior affected to these gray elements, special attention is paid to them. As far as the question of the solvers is concerned, generic FEM codes are found to lack efficiency: they cannot reach high enough levels of discretization with classical free meshes, and they do not take advantage of the regular structure of the mesh. Thus, a specific finite differences/finite volumes solver has been developed. At first, generic off-the-shelf linear system solvers were used. To further improve the efficiency in terms of memory requirements, specific variants of the preconditioned conjugate gradient were implemented. This allowed to homogenize the conductivity of a concrete-like microstructure using more than 10{sup 9} degrees of freedom on a rather common hardware for 2010 (a PC embedding 48 GB of RAM). Taking benefit of the properties of the regular Cartesian grid we have also investigated a multi-level method to improve the CPU efficiency of the code.

36 MATERIALS SCIENCE↗