Engineering topics

Sandlin, D. R.

Publications and source records attributed to Sandlin, D. R..

18 records

NASA NTRS1986

Application of a low order panel method to complex three-dimensional internal flow problems

An evaluation of the ability of a low order panel method to predict complex three-dimensional internal flow fields was made. The computer code VSAERO was used as a basis for the evaluation. Guidelines for modeling internal flow geometries were determined and the effects of varying the boundary conditions and the use of numerical approximations on the solutions accuracy were studied. Several test cases were run and the results were compared with theoretical or experimental results. Modeling an internal flow geometry as a closed box with normal velocities specified on an inlet and exit face provided accurate results and gave the user control over the boundary conditions. The values of the boundary conditions greatly influenced the amount of leakage an internal flow geometry suffered and could be adjusted to eliminate leakage. The use of the far-field approximation to reduce computation time influenced the accuracy of a solution and was coupled with the values of the boundary conditions needed to eliminate leakage. The error induced in the influence coefficients by using the far-field approximation was found to be dependent on the type of influence coefficient, the far-field radius, and the aspect ratio of the panels.

Ashby, D. L.↗

NASA NTRS1986

Identification of linearized equations of motion for the fixed wing configuration of the rotor systems research aircraft

The purpose of this report is to establish linear, decoupled models of rigid body motion for the fixed wing configuration of the Rotor Systems Research Aircraft (RSRA). Longitudinal and lateral control surface fixed linear models were created from aircraft time histories using current system identification techniques. Models were obtained from computer simulation at 160 KCAS and 200 KCAS, and from flight data at 160 KCAS. Comparisons were performed to examine modeling accuracy, variation of dynamics with airspeed and correlation of simulation and flight data results. The results showed that the longitudinal and lateral linear models accurately predicted RSRA dynamics. The flight data results showed that no significant handling qualities problems were present in the RSRA fixed wing aircraft at the flight speed tested.

Balough, D. L.↗

NASA NTRS1986

A survey of handling qualities criteria and their applications to high performance aircraft

Various handling qualities criteria and their application to high performance aircraft including state-of-the-art and highly augmented aircraft were surveyed. Neal-Smith, Bandwidth, Equivalent Systems, and Military Specification 8785 criteria are applied to flight test data from aircraft such as the F-8 Digital Fly-By-Wire, the YF-12, and an Advanced Fighter Aircraft. Backgrounds and example applications of each criteria are given. The results show that the handling qualities criteria investigated can be applied to highly augmented aircraft with fairly good results in most cases; however, since no one method excelled, more than one criteria should be used whenever possible. Equivalent time delays appear to be the most frequent critical factor in determining pilot rating levels of highly augmented aircraft.

Peahl, D. L.↗

NASA NTRS1985

An experimental and analytical method for approximate determination of the tilt rotor research aircraft rotor/wing download

The XV-15 Tilt Rotor Research Aircraft download phenomenon was analyzed. This phenomenon is a direct result of the two rotor wakes impinging on the wing upper surface when the aircraft is in the hover configuration. For this study the analysis proceeded along tow lines. First was a method whereby results from actual hover tests of the XV-15 aircraft were combined with drag coefficient results from wind tunnel tests of a wing that was representative of the aircraft wing. Second, an analytical method was used that modeled that airflow caused gy the two rotors. Formulas were developed in such a way that acomputer program could be used to calculate the axial velocities were then used in conjunction with the aforementioned wind tunnel drag coefficinet results to produce download values. An attempt was made to validate the analytical results by modeling a model rotor system for which direct download values were determinrd..

Jordon, D. E.↗

NASA NTRS1985

Flow direction measurement criteria and techniques planned for the 40- by 80-/80- x 120-foot wind tunnel integrated systems tests

A study was performed in order to develop the criteria for the selection of flow direction indicators for use in the Integrated Systems Tests (ISTs) of the 40 by 80/80 by 120 Foot Wind Tunnel System. The problems, requirements, and limitations of flow direction measurement in the wind tunnel were investigated. The locations and types of flow direction measurements planned in the facility were discussed. A review of current methods of flow direction measurement was made and the most suitable technique for each location was chosen. A flow direction vane for each location was chosen. A flow direction vane that employs a Hall Effect Transducer was then developed and evaluated for application during the ISTs.

Zell, P. T.↗

NASA NTRS1985

The use of a panel code on high lift configurations of a swept forward wing

A study was done on high lift configurations of a generic swept forward wing using a panel code prediction method. A survey was done of existing codes available at Ames, frow which the program VSAERO was chosen. The results of VSAERO were compared with data obtained from the Ames 7- by 10-foot wind tunnel. The results of the comparison in lift were good (within 3.5%). The comparison of the pressure coefficients was also good. The pitching moment coefficients obtained by VSAERO were not in good agreement with experiment. VSAERO's ability to predict drag is questionable and cannot be counted on for accurate trends. Further studies were done on the effects of a leading edge glove, canards, leading edge sweeps and various wing twists on spanwise loading and trim lift with encouraging results. An unsuccessful attempt was made to model spanwise blowing and boundary layer control on the trailing edge flap. The potential results of VSAERO were compared with experimental data of flap deflections with boundary layer control to check the first order effects.

Scheib, J. S.↗

NASA NTRS1984

Comparison of theoretical and flight-measured local flow aerodynamics for a low-aspect-ratio fin

Flight test and theoretical aerodynamic data were obtained for a flight test fixture mounted on the underside of an F-104G aircraft. The theoretical data were generated using two codes, a two dimensional transonic code called Code H, and a three dimensional subsonic and supersonic code call wing-body. Pressure distributions generated by the codes for the flight test fixture as well as boundary layer displacement thickness generated by the two dimensional code were compared to the flight test data. The two dimensional code pressure distributions compared well except at the minimum pressure point and trailing edge. Shock locations compared well except at high transonic speeds. The three dimensional code pressure distributions compared well except at the trailing edge of the flight test fixture. The two dimensional code does not predict displacement thickness of the flight test fixture well.

Johnson, J. B.↗

NASA NTRS1984

Development of flight testing techniques

A list of students involved in research on flight analysis and development is given along with abstracts of their work. The following is a listing of the titles of each work: Longitudinal stability and control derivatives obtained from flight data of a PA-30 aircraft; Aerodynamic drag reduction tests on a box shaped vehicle; A microprocessor based anti-aliasing filter for a PCM system; Flutter prediction of a wing with active aileron control; Comparison of theoretical and flight measured local flow aerodynamics for a low aspect ratio fin; In flight thrust determination on a real time basis; A comparison of computer generated lift and drag polars for a Wortmann airfoil to flight and wind tunnel results; and Deep stall flight testing of the NASA SGS 1-36.

Sandlin, D. R.↗

NASA NTRS1984

A microprocessor based anti-aliasing filter for a PCM system

Described is the design and evaluation of a microprocessor based digital filter. The filter was made to investigate the feasibility of a digital replacement for the analog pre-sampling filters used in telemetry systems at the NASA Ames-Dryden Flight Research Facility (DFRF). The digital filter will utilize an Intel 2920 Analog Signal Processor (ASP) chip. Testing includes measurements of: (1) the filter frequency response and, (2) the filter signal resolution. The evaluation of the digital filter was made on the basis of circuit size, projected environmental stability and filter resolution. The 2920 based digital filter was found to meet or exceed the pre-sampling filter specifications for limited signal resolution applications.

Morrow, D. C.↗

NASA NTRS1984

The performance evaluation of a jet flap on an advanced supersonic harrier

The performance concept of a supersonic vertical and short takeoff and landing (V/STOL) fighter, model 279-3, modified to utilize a jet flap was evaluated. Replacing the rear nozzles of the 279-3 with the jet flap favorably alters the pressure distribution over the airfoil and dramatically increases lift. The result is a significant decrease in takeoff distance, an increase in payload, and an improvement in combat performance. To investigate the benefit in increased payload, the 279-3 and the jet flapped 279-3JF were modeled on the NASA Aircraft Synthesis (ACSYNT) computer code and flown on a 250 feet takeoff distance interdiction mission. The increase in payload weight that the 279-3JF could carry was converted into fuel in one case, and in another, converted to bomb load. When the fuel was increased, the 279-3JF penetrated into enemy territory almost four times the distance of 279-3, and therefore increased mission capability. When the bomb load was increased, the 279-3JF carried 14 bombs the same distance the 279-3 carried four. The increase in mission performance and improvements in turning rates was realized with only a small penalty in increased empty weight.

Lipera, L. D.↗

NASA NTRS1984

A comparison of computer-generated lift and drag polars for a Wortmann airfoil to flight and wind tunnel results

Computations of drag polars for a low-speed Wortmann sailplane airfoil are compared to both wind tunnel and flight results. Excellent correlation is shown to exist between computations and flight results except when separated flow regimes were encountered. Wind tunnel transition locations are shown to agree with computed predictions. Smoothness of the input coordinates to the PROFILE airfoil analysis computer program was found to be essential to obtain accurate comparisons of drag polars or transition location to either the flight or wind tunnel results.

Bowers, A. H.↗

NASA NTRS1984

Flight determination of the aerodynamic stability and control characteristics of the NASA SGS 1-36 sailplane in the conventional and deep stall angles-of-attack of between -5 and 75 degrees

The flight test procedure and the preliminary analysis of the results obtained from twenty manned flights of the SGS 1-36 in the high angles of attack Deep Stall region are discussed. A comparison of the flight determined stability and control derivatives, those of the wind tunnel, and the estimated aerodynamic data is also presented. Furthermore, deep stall dynamics response of the SGS 1-36 is discussed briefly to explain some of the unexpected flight observations.

Mahdavi, F. A.↗

NASA NTRS1983

Flutter prediction for a wing with active aileron control

A method for predicting the vibrational stability of an aircraft with an analog active aileron flutter suppression system (FSS) is expained. Active aileron refers to the use of an active control system connected to the aileron to damp vibrations. Wing vibrations are sensed by accelerometers and the information is used to deflect the aileron. Aerodynamic force caused by the aileron deflection oppose wing vibrations and effectively add additional damping to the system.

Penning, K.↗

NASA NTRS1982

Wind tunnel tests of a free-wing/free-trimmer model

The riding qualities of an aircraft with low wing loading can be improved by freeing the wing to rotate about its spanwise axis. A trimming surface also free to rotate about its spanwise axis can be added at the wing tips to permit the use of high lift devices. Wind tunnel tests of the free wing/free trimmer model with the trimmer attached to the wing tips aft of the wing chord were conducted to validate a mathematical model developed to predict the dynamic characteristics of a free wing/free trimmer aircraft. A model consisting of a semispan wing with the trimmer mounted on with the wing on an air bearing and the trimmer on a ball bearing was displaced to various angles of attack and released. The damped oscillations of the wing and trimmer were recorded. Real and imaginary parts of the characteristic equations of motion were determined and compared to values predicted using the mathematical model.

Sandlin, D. R.↗

NASA NTRS1981

Aerodynamic drag reduction tests on a box-shaped vehicle

The intent of the present experiment is to define a near optimum value of drag coefficient for a high volume type of vehicle through the use of a boattail, on a vehicle already having rounded front corners and an underbody seal, or fairing. The results of these tests will constitute a baseline for later follow-on studies to evaluate candidate methods of obtaining afterbody drag coefficients approaching the boattail values, but without resorting to such impractical afterbody extensions. The current modifications to the box-shaped vehicle consisted of a full and truncated boattail in conjunction with the faired and sealed underbody. Drag results from these configurations are compared with corresponding wind tunnel results of a 1/10 scale model. Test velocities ranged up to 96.6 km/h (60 mph) and the corresponding Reynolds numbers ranged up to 1.3 x 10 to the 7th power based on the vehicles length which includes the boattail. A simple coast-down technique was used to define drag.

Peterson, R. L.↗

NASA NTRS1981

Longitudinal stability and control derivatives obtained from flight data of a PA-30 aircraft

In order to obtain reliable and accurate values of the stability and control derivatives, the Dryden Fligh Research Center (DFRC) developed a technique for extracting the derivatives from flight data. This technique is implemented by a set of FORTRAN computer programs that is based on a modified maximum likelihood estimator that uses the Newton-Raphson algorithm to perform the required minimization of the derivatives. Data was obtained with a PA-30, light twin-engine general aviation aircraft in zero, half, and full flap configuration in level unaccelerated flight with the landing gear retracted. The derivatives were plotted as functions of angle of attack using various graphical arrangements to show variations of wind tunnel and flight determined values at zero flap settings. Also, data was displayed to show the effects of flap deflection and thrust variation on the longitudinal stability derivatives. The angle of attack and angle of sideslip were measured. The dynamic pressure, velocity, and altitude were calculated, using a FORTRAN computer program, from the static and dynamic pressures. The control deflections of the stabilator, ailerons, and rudder also were recorded along with left throttle position, engine rpm, and manifold pressure.

Turley, D. R.↗

NASA NTRS1981

Flight evaluation of the terminal guidance system

The terminal guidance system (TGS) is avionic equipment which gives guidance along a curved descending flight path to a landing. A Cessna 182 was used as the test aircraft and the TGS was installed and connected to the altimeter, DME, RMI, and gyro compass. Approaches were flown by three different pilots. When the aircraft arrives at the termination point, it is set up on final approach for a landing. The TGS provides guidance for curved descending approaches with guideslopes of 6 deg which required, for experienced pilots, workloads that are approximately the same as for an ILS. The glideslope is difficult to track within 1/2 n.m. of the VOR/DME station. The system permits, for experienced pilots, satisfactory approaches with a turn radius as low as 1/2 n.m. and a glideslope of 6 deg. Turn angles have little relation to pilot workload for curved approaches. Pilot experience is a factor for curved approaches. Pilots with low instrument time have difficulty flying steep approaches with small turn radius. Turbulence increases the pilot workload for curved approaches. The TGS does not correct to a given flight path over the ground nor does it adequately compensate for wind drift.

Sandlin, D. R.↗

NASA NTRS1979

Wind tunnel investigation of the free-wing/free trimmer concept

The conclusions arrived at in this investigation are: (1) the free-wing/free-trimmer configuration is a viable concept, and exhibited both static and dynamic stability for a trimmer pivot at the 10 percent chord position; (2) unless properly controlled, friction in the mounting system and instrumentation can significantly affect the panel response; and (3) for the configurations tested, the control was far too sensitive, giving the full range of wing angle-of-attack for trimmer flap displacements of only a few degrees.

Sandlin, D. R.↗