Search NASA⌕ Search

Engineering topics

Santhanagopalan, Shriram

Publications and source records attributed to Santhanagopalan, Shriram.

17 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Observation and Modeling of Dynamic Fracture Behaviors of Battery Cell Under Impact Loading Using Enhanced Representative Volume Element Concept

The burgeoning electric automobile industry has increased interest in battery safety. Battery cells experience significant mechanical stress during operation, including the impact of accidents and vibrations from driving. The potential for thermal runaway reactions in battery cells raises safety concerns. Although numerous researchers have defined the dynamic behavior of battery cells and proposed numerical models to describe it, few studies have focused on the high-strain rate mechanical impact phase correlated with the onset of fracture. In this study, we describe the dynamic behavior of pouch battery cells and propose a modeling method to study their mechanical failure under impact situations. Impact tests are conducted at various velocities and heights. To overcome numerical issues commonly encountered under rapid deformation scenarios, a new finite element model is developed based on the representative volume element model. The proposed approach efficiently simulates continuous crack propagation and brittleness behavior during impact by permitting the individual behavior of the cell components. Therefore, engineers can reliably design safer electric vehicle battery cells by measuring the properties of the cell components.

ENERGY STORAGE↗
DOE OSTI2024

Coupled Multiphysics Modeling of Lithium-Ion Batteries for Automotive Crashworthiness Applications

Considerable advances have been made in battery safety models, but achieving predictive accuracy across a wide range of conditions continues to be challenging. Interactions between dynamically evolving mechanical, electrical, and thermal state variables make model prediction difficult during mechanical abuse scenarios. In this study, we develop a physics-based modeling approach that allows for choosing between different mechanical and electrochemical models depending on the required level of analysis. We demonstrate the use of this approach to connect cell-level abuse response to electrode-level and particle-level transport phenomena. A pseudo-two-dimensional model and simplified single-particle models are calibrated to electrical-thermal cycling data and applied to mechanically induced short-circuit scenarios to understand how the choice of electrochemical model affects the model prediction under abuse scenarios. These models are implemented using user-defined subroutines on ls-dyna finite element software and can be coupled with existing automotive crash safety models.

analysis and design of components↗
DOE OSTI2024

Li-Ion Battery Thermal Characterization for Thermal Management Design

Battery design efforts often prioritize enhancing the energy density of the active materials and their utilization. However, optimizing thermal management systems at both the cell and pack levels is also key to achieving mission-relevant battery design. Battery thermal management systems, responsible for managing the thermal profile of battery cells, are crucial for balancing the trade-offs between battery performance and lifetime. Designing such systems requires accounting for the multitude of heat sources within battery cells and packs. This paper provides a summary of heat generation characterizations observed in several commercial Li-ion battery cells using isothermal battery calorimetry. The primary focus is on assessing the impact of temperatures, C-rates, and formation cycles. Moreover, a module-level characterization demonstrated the significant additional heat generated by module interconnects. Characterizing heat signatures at each level helps inform manufacturing at the design, production, and characterization phases that might otherwise go unaccounted for at the full pack level. Further testing of a 5 kWh battery pack revealed that a considerable temperature non-uniformity may arise due to inefficient cooling arrangements. To mitigate this type of challenge, a combined thermal characterization and multi-domain modeling approach is proposed, offering a solution without the need for constructing a costly module prototype.

25 ENERGY STORAGE↗
DOE OSTI2024

Methods and devices for electrochemical relithiation of lithium-ion batteries

Among other things, the present disclosure relates to re-purposing used lithium-ion batteries. The present disclosure includes treating an electrode using a solvent prior to electrochemically relithiating the electrode. In some embodiments, the relithiation may be done using a roll-to-roll device, wherein the electrode may be secured on a first pin and a second pin, then it may be unwound and submerged in an electrolyte solution. Lithium ions may be inserted into the electrode using a voltage. The layer of lithium may provide lithium ions to the electrode.

Smith, Kandler Alan↗
DOE OSTI2023

Simulation of Impedance Changes with Aging in Lithium Titanate-based Cells Using Physics-Based Dimensionless Modeling

Quantifying aging effects in lithium-ion cells with chemistries that have a flat open circuit potential is challenging. We implement a physics-based electrochemical model to track changes in the electrochemical impedance response of lithium titanate-based cells. Frequency domain equations of a pseudo two-dimensional model are made dimensionless, and the corresponding non-dimensional parameters are estimated using a Levenberg-Marquardt routine. The model weighs the relative contributions of changes in diffusion, ionic conduction within the electrolyte phase against solid phase electronic conduction towards cell aging. Solid-phase diffusion, charge transfer resistance and double layer capacitance at the solid-liquid interface are accounted for in the particle impedance. The estimation routine tracks dimensionless parameters using accelerated cycling data from full cells over 1000 cycles. The model can be deployed within a short time for state estimation using physics-based models without requiring prior knowledge of the battery chemistry, format, or capacity.

25 ENERGY STORAGE↗
DOE OSTI2023

Observation and Modeling of the Thermal Runaway of High-Capacity Pouch Cells Due to an Internal Short Induced by an Indenter

Owing to the complexity of coupling mechanical and electrical solvers for finite element analysis (FEA) of mechanical abuse of a battery, the simulation should be performed by incorporating a local short circuit model activated based on the status of battery elements. However, the approach should also consider various other conditions of the battery simulated, such as the initial state of charge (SOC), for precise simulations of the internal short. This study proposes an approach developed with a mechanical model and single-particle battery model, along with a reaction kinetics model for thermal abuse using LS-DYNA. Several key parameters were selected, such as the activation criteria, kinetic abuse and element integration points during the internal short circuit induced by the indenter. The impact of these key parameters in the FEA on thermal runaway response for various initial SOCs from 25 to 100 % were analyzed. The FEA results obtained were compared against experimental results with various parameters such as activation criterion of internal short, kinetic abuse based on accelerating rate calorimetry (ARC) data. Finally, the root causes of the discrepancy between the FEA and experimental results are discussed regarding integration point what solver can make difference during calculation.

ENERGY STORAGE↗
DOE OSTI2023

Chapter 6: Abuse Response of Batteries Subjected to Mechanical Impact

Electrochemical and thermal models to simulate nominal performance and abuse response of lithium-ion cells and batteries have been reported widely in the literature. Studies on mechanical failure of cell components and how such events interact with the electrochemical and thermal response are relatively less common. This chapter outlines a framework developed under the Computer Aided Engineering for Batteries program to couple failure modes resulting from external mechanical loading to the onset and propagation of electrochemical and thermal events that follow. Starting with a scalable approach to implement failure criteria based on thermal, mechanical, and electrochemical thresholds, we highlight the practical importance of these models using case studies at the cell and module level. The chapter also highlights a few gaps in our understanding of the comprehensive response of batteries subjected to mechanical crash events, the stochastic nature of some of these failure events, and our approach to build safety maps that help improve robustness of battery design by capturing the sensitivity of some key design parameters to heat generation rates under different mitigation strategies.

abuse simulations↗
DOE OSTI2023

NAATBatt North American Lithium-Ion Battery Supply Chain Database Documentation and User Guide

NAATBatt International funded NREL to develop a database of companies that supply goods, equipment, and services used to manufacture or recycle high voltage lithium-ion battery packs and cells in North America under a Technical Services Agreement (TSA-21-17854) with NREL. The database is in Excel and accompanied PPT file summarizes this work and document the use guide in a PPT file.

anode↗
DOE OSTI2022

A Comprehensive Numerical and Experimental Study for the Passive Thermal Management in Battery Modules and Packs

Cooling plates in battery packs of electric vehicles play critical roles in passive thermal management systems to reduce risks of catastrophic thermal runaway. In this work, a series of numerical simulations and experiments are carried out to unveil the role of cooling plates (both between cells and a bottom plate parallel to the cell stack) on the thermal behavior of battery modules and packs under nail penetrations. First, we investigated the role of side cooling plates on the thermal runaway propagation mitigation in battery modules (1S3P) and packs (3S3P) by varying the key parameters of the side cooling plates, such as plate thicknesses, thermal contact resistances, and materials. Then, three important factors for passive thermal management systems are identified: (i) thermal mass of side cooling plates, (ii) interfacial thermal contact resistances, and (iii) the effective heat transfer coefficients at exterior surfaces. The roles of bottom cooling plates on thermal runaway propagation mitigation in 1S3P and 1S5P battery modules are numerically investigated by comparing the thermal behavior of the modules with only side cooling plates and with both side and bottom cooling plates.

25 ENERGY STORAGE↗
DOE OSTI2022

A Robust Numerical Treatment of Solid-Phase Diffusion in Pseudo Two-Dimensional Lithium-Ion Battery Models

Solid-phase diffusion in active materials of lithium-ion batteries significantly affects charging and safety-related behavior of lithium-ion batteries. Therefore, it is essential to develop an efficient and robust numerical algorithm for solving solid-phase diffusion equations in physics-based battery models. In this work, we discuss the origins of numerical instabilities that can occur when solving the solid-phase diffusion equations using iterative methods. Then, in order to resolve such issues, we propose a simple numerical treatment to the surface flux term of discretized solid-phase diffusion equations. To demonstrate its numerical robustness, the proposed method is implemented into a pseudo two-dimensional (P2D) physics-based battery model and simulations are conducted at wide ranges of operating conditions. Even with extremely poor initial guesses for the Li+ concentrations of the active materials, computations using the proposed method do not diverge and the their computational speeds are comparable to those with conventional initial guesses. Comprehensive tests of the proposed method are also performed with a dynamic current profile based on US06 driving profile and a multi-stage charging profile with very high initial C-rate (12C).

battery modeling↗
DOE OSTI2022

Chapter 8: Life-Cycle Testing and Analysis

Prior to a spacecraft launch, program mission assurance standards dictate that the flight battery power system should comply with mission requirements under the intended operating conditions. Ground life cycle testing (LCT) combined with an analysis on the electrical power system (EPS) battery is an empirical method used to demonstrate compliance to satellite service life requirements. The LCT compliance method adopted by the aerospace industry is based on demonstrating a space battery's life expectancy as a part of battery qualification. Real-time cell and lithium-ion battery (LIB) LCT data are commonly used for model inputs to EPS power and energy balance analyses, in LIB reliability analysis estimates, and to support on-orbit spacecraft mission life extension opportunities. This chapter describes the LCT planning steps, process approach, and analysis techniques commonly used to qualify space LIB power systems.

accelerated aging↗
DOE OSTI2022

Batteries (2021 Annual Progress Report)

This document summarizes the progress of VTO battery R&D projects supported during the fiscal year 2021 (FY 2021). In FY 2021, the DOE VTO battery R&D funding was approximately $\$$115 million. Its R&D focus was on the development of high-energy batteries for EVs as well as very high-power devices for hybrid vehicles. The electrochemical energy storage roadmap (which can be found at the EERE Roadmap web page2) describes ongoing and planned efforts to develop electrochemical storage technologies for EVs. To advance battery technology, which can in turn improve market penetration of PEVs, the program investigates various battery chemistries to overcome specific technical barriers, e.g., battery cost, performance, life (both the calendar life and the cycle life), its tolerance to abusive conditions, and its recyclability/sustainability. VTO R&D has had considerable success, lowering the cost of EV battery packs to $\$$185/kWh in 2019 (representing more than 80% reduction since 2008) yet even further cost reduction is necessary for EVs to achieve head-to-head cost competitiveness with ICEs (without Federal subsidies). In addition, today’s batteries also need improvements in such areas as their ability to accept charging at a high rate, referred to as extreme fast charging (XFC) (15 minute charge) – to provide a “refueling” convenience similar to ICEs, and the ability to operate adequately at low temperatures. Research into “next-gen lithium-ion” batteries which would provide such functionalities is one of the R&D focus areas. VTO is funding research on both “next gen” chemistries (which employ an alloy anode and/or a high voltage cathode) and beyond lithium-ion (BLI) chemistries (which can, for example, employ a lithium metal anode).

25 ENERGY STORAGE↗
DOE OSTI2022

Comprehensive Characterization of Multi-Phase Sulfurized Polyacrylonitrile Cathodes for Lithium-Sulfur Batteries

Sulfurized polyacrylonitrile (SPAN) is considered one of the most promising cathode materials to overcome the operational challenges that plague lithium-sulfur (Li-S) batteries. However, material properties and electrochemical performance implications of SPAN prepared under different synthesis conditions are not yet fully investigated. In this study, we show the impacts of different synthesis conditions on the formation of sulfur to PAN bonds and redox reaction mechanisms of multi-phase SPAN via comprehensive material and electrochemical characterizations. In-situ Raman analysis was first applied to study the multi-phase SPAN-based Li-S cells. We found that both elemental sulfur and chemically bonded sulfur are present under the synthesis condition of 300 degree C/3 h along with unreacted PAN. The incompletely sulfurized, multi-phase SPAN exhibited an unusually rapid capacity degradation in the resultant Li-S cells, which is attributed to polysulfide formation and continuously growing interfacial impedance in the Li-S cells. On the other hand, SPAN samples prepared under the synthesis condition of 350 degree C/3 h are found completely sulfurized with chemically bonded sulfur to the PAN backbone without the presence of free elemental sulfur. Complete sulfurization of SPAN led to exceptionally stable cycle performance due to excellent reversible redox processes of chemically bonded sulfur with Li+ in the Li-S cells.

DIRECT ENERGY CONVERSION,ENERGY STORAGE↗
DOE OSTI2022

A Framework to Analyze the Requirements of a Multiport Megawatt-Level Charging Station for Heavy-Duty Electric Vehicles

Widespread adoption of heavy-duty (HD) electric vehicles (EVs) will soon necessitate the use of megawatt (MW)-scale charging stations to charge high-capacity HD EV battery packs. Such a station design needs to anticipate possible station traffic, average and peak power demand, and charging/wait time targets to improve throughput and maximize revenue-generating operations. High-power direct current charging is an attractive candidate for MW-scale charging stations at the time of this study, but there are no precedents for such a station design for HD vehicles. We present a modeling and data analysis framework to elucidate the dependencies of a MW-scale station operation on vehicle traffic data and station design parameters and how that impacts vehicle electrification. This framework integrates an agent-based charging station model with vehicle schedules obtained through real-world vehicle telemetry data analysis to explore the station design and operation space. A case study applies this framework to a Class 8 vehicle telemetry dataset and uses Monte Carlo simulations to explore various design considerations for MW-scale charging stations and EV battery technologies. The results show a direct correlation between optimal charging station placement and major traffic corridors such as cities with ports, e.g., Los Angeles and Oakland. Corresponding parametric sweeps reveal that while good quality of service can be achieved with a mix of 1.2-megawatt and 100-kilowatt chargers, the resultant fast charging time of 35–40 min will need higher charging power to reach parity with refueling times.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Hierarchical Control of Megawatt-Scale Charging Stations for Electric Trucks with Distributed Energy Resources

Electrifying medium- and heavy-duty trucks is critical to decarbonizing the transportation sector. Energy needs of electric trucks will likely require megawatt-scale charging stations, which could significantly stress the electric distribution grid. Distributed energy resources (DER) can alleviate this stress and reduce charging costs with proper management. To that end, this work develops a hierarchical predictive control algorithm for future multi-port megawatt-scale charging stations that can provide real-time energy management for stations, decide charging rates, dispatch energy storage system (ESS), and provide grid voltage support. We integrate three algorithmic components: (i) an energy management optimization (EMO) that provides supervisory control to DER assets and charging loads at minute scale, (ii) a real-time energy management system (RT-EMS) that heuristically compensates for fast disturbances at sub-second scale, and (iii) a model predictive control (MPC)-based battery management system (BMS) that communicates future charging demands to the EMO, to manage the overall megawatt-scale site. Additionally, validation in a controller hardware-in-the-loop (CHIL) environment shows that the hierarchical controller can reduce the total energy consumption from the grid by approximately 28% compared to an uncontrolled case for the station configuration in this paper, without impacting charging time.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2022

Lithium nitride coatings deposited by magnetron sputtering on sulfide electrolytes for solid-state batteries

Lithium nitrides have been considered as promising candidates for interfacial layers in solid-state lithium batteries (SSBs). Previously reported lithium nitride (Li 3 N) coatings were mostly prepared by the reaction between lithium metal and nitrogen gas, which makes it challenging for their thickness control and integration in SSBs. In this study, we prepare Li 3 N via magnetron sputtering for the first time, and apply the resulting coating directly on sulfide solid-state electrolyte. A much smaller impedance increase associated with improved cycling performance is observed in lithium metal symmetric cell. These results demonstrate the feasibility of depositing Li 3 N via magnetron sputtering and its application in SSBs.

25 ENERGY STORAGE↗