Search NASA⌕ Search

Engineering topics

Saraf, Laxmikant V

Publications and source records attributed to Saraf, Laxmikant V.

At least 19 records

Hard X-ray Fluorescence Measurements of Heteroepitaxial Solid Oxide Fuel Cell Cathode Materials

Commonly, SOFCs are operated at high temperatures (above 800°C). At these temperatures expensive housing is needed to contain an operating stack as well as coatings to contain the oxidation of the metallic interconnects. Lowering the temperature of an operating device would allow for more conventional materials to be used, thus lowering overall cost. Understanding the surface chemical states of cations in the surface of the SOFC cathode is vital to designing a system that will perform well at lower temperatures. The samples studied were grown by pulsed laser deposition (PLD) at the Environmental Molecular Sciences Laboratory (EMSL) at Pacific Northwest National Laboratory (PNNL). 20% strontium doped lanthanum manganite (LSM-20) was grown on YSZ and NGO (neodymium gallate). The films on YSZ have a fiber texture. LSM-20 on NGO is heteroepitaxial. Lanthanum strontium cobalt ferrite (LSCF-6428) films were grown on LAO and YSZ with a GDC barrier layer. Total X-ray Reflection Fluorescence (TXRF) was used to depth profile the samples. In a typical experiment, the angle of the incident beam is varied though the critical angle. Below the critical angle, the x-ray decays as an evanescent wave and will only penetrate the top few nanometers. TXRF experiments done on LSM films have suggested strontium segregates to the surface and form strontium enriched nanoparticles (1). It should be pointed out that past studies have focused on 30% strontium A-site doping, but this project uses 20% strontium doped lanthanum manganite. XANES and EXAFS data were taken as a function of incoming angle to probe composition as a function of depth. XANES spectra can be difficult to analyze fully. For other materials density functional theory calculations compared to near edge measurements have been a good way to understand the 3d valence electrons (2).

Environmental Molecular Sciences Laboratory↗

Sodium Ion Insertion in Hollow Carbon Nanowires for Battery Applications

Hollow Carbon Nanowires (HCNWs) were prepared through pyrolyzation of hollow polyaniline nanowires precursor. The HCNWs used as anode material for Na-ion batteries delivers a high reversible capacity of 251 mAh g{sup -1} and 82.2% capacity retention over 400 charge/discharge cycles between 1.2 and 0.01 V (vs. Na{sup +}/Na) at a constant current of 50 mA g{sup -1} (0.2 C). Excellent cycling stability is also observed at even higher charge-discharge rate. A high reversible capacity of 149 mAh g{sup -1} also can be obtained at a current rate of 500 mA g{sup -1} (2C). The good Na ion insertion property is attributed to the short diffusion distance in the HCNWs, and the large interlayer distance (0.37 nm) between the graphitic sheets, which agrees with the interlayered distance predicted by theoretical calculation to enable Na ion insertion in carbon materials.

74 ATOMIC AND MOLECULAR PHYSICS↗

Selective Metal Cation Capture by Soft Anionic Metal-Organic Frameworks via Drastic Single-Crystal-to-Single-Crystal Transformations

Flexible anionic metal-organic frameworks transform to neutral heterobimetallic systems via single-crystal-to-single-crystal processes invoked by cation insertion. These transformations are directed by cooperative bond breakage and formation, resulting in expansion or contraction of the 3D framework by up to 33% due to the flexible nature of the organic linker. These MOFs displays highly selective uptake of divalent transition metal cations (Co2+ and Ni2+ for example) over alkali metal cations (Li+ and Na+).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Location Of Hole And Electron Traps On Nanocrystalline Anatase TiO2

The defect photoluminescence from TiO2 nanoparticles in the anatase phase is reported for nanosheets which expose predominantly (001) surfaces, and compared to that from conventional anatase nanoparticles which expose mostly (101) surfaces. Also reported is the weak defect photoluminescence of TiO2 nanotubes, which we find using electron back-scattered diffraction to consist of walls which expose (110) and (100) facets. The nanotubes exhibit photoluminescence that is blue-shifted and much weaker than that from conventional TiO2 nanoparticles. Despite the preponderance of (001) surfaces in the nanosheet samples, they exhibit photoluminescence similar to that of conventional nanoparticles. We assign the broad visible photoluminescence of anatase nanoparticles to two overlapping distributions: hole trap emission associated with oxygen vacancies on (101) exposed surfaces, which peaks in the green, and a broader emission extending into the red which results from electron traps on under-coordinated titanium atoms, which are prevalent on (001) facets. The results of this study suggest how morphology of TiO2 nanoparticles could be optimized to control the distribution and activity of surface traps. Our results also shed light on the mechanism by which the TiCl4 surface treatment heals traps on anatase and mixed-phase TiO2 films, and reveals distinct differences in the trap-state distributions of TiO2 nanoparticles and nanotubes. The molecular basis for electron and hole traps and their spatial separation on different facets is discussed.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Dependence of the Electron Beam Energy and Types of Surface to Determine EBSD Indexing Reliability in Yttria-Stabilized Zirconia

Electron backscatter diffraction (EBSD) is a powerful technique for the surface microstructure analysis. EBSD analysis of cubic yttria-stabilized zirconia (YSZ) in two and three dimensions (2-D, 3-D) is demonstrated using sequential slicing from a focused ion beam (FIB) followed by EBSD mapping to represent 3-D reconstructed high density grain structure with random orientation. The statistics related to accuracy of EBSD band detection shows that probability of accurate grain orientation detection increased significantly when the electron beam energy is increased from 10 kV to 30 kV. As a result of better sampling with increased interaction volume, a disparity between local and average grain orientation angle also exhibited the dependence of the electron beam energy to determine the accuracy of grain orientation. To study the accuracy and quality of EBSD band detection as a function of surface roughness and over layer formation, rapid EBSD measurement tests are performed on (a) YSZ surfaces ion-polished at ion beam energies of 65 nA at 30 kV and 1 nA at 30 kV and (b) carbon coated versus uncoated YSZ surfaces. The EBSD results at both 10 kV and 30 kV electron beam energies indicate that EBSD band detection accuracy is negatively affected by surface roughness and amorphous over layer formation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Soft X-Ray Spectroscopic Study of Dense Strontium-Doped Lanthanum Manganite Cathodes for Solid Oxide Fuel Cell Applications

The evolution of the Mn charge state, chemical composition, and electronic structure of La{sub 0.8}Sr{sub 0.2}MnO{sub 3} (LSMO) cathodes during the catalytic activation of solid oxide fuel cell (SOFC) has been studies using X-ray spectroscopy of as-processed, exposed, and activated dense thin LSMO films. Comparison of O K-edge and Mn L{sub 3,2}-edge X-ray absorption spectra from the different stages of LSMO cathodes revealed that the largest change after the activation occurred in the Mn charge state with little change in the oxygen environment. Core-level X-ray photoemission spectroscopy and Mn L{sub 3} resonant photoemission spectroscopy studies of exposed and as-processed LSMO determined that the SOFC environment (800 C ambient pressure of O{sub 2}) alone results in La deficiency (severest near the surface with Sr doping >0.55) and a stronger Mn{sup 4+} contribution, leading to the increased insulating character of the cathode prior to activation. Meanwhile, O K-edge X-ray absorption measurements support Sr/La enrichment nearer the surface, along with the formation of mixed Sr{sub x}Mn{sub y}O{sub z} and/or passive MnO{sub x} and SrO species.

30 DIRECT ENERGY CONVERSION↗

Optimization of mesoporous carbon structures for lithium–sulfur battery applications

Mesoporous carbon (MC) with tunable pore sizes (22nm, 12nm, 7nm, and 3nm) and pore volumes (from 1.3 to 4.8 cc/g) containing sulfur inside the pores were systematically studied as mesoporous carbon-sulfur (MCS) composite electrodes for Li-S batteries. Investigation on these MCS composites reveals that the pore structure has no influence on the battery performance at full sulfur loading conditions (the pore volume is fully filled by sulfur) but the maximum sulfur loading capability is higher for MC with larger pore volume. MC with large pore volumes, partial sulfur filling (part of the pore volume left unfilled), and surface modification, can have reasonably high sulfur loading, improved electrical and ionic contacts of sulfur with MC and with electrolytes, which subsequently promotes the battery performance. An initial capacity of ~1250 mAh/g (based on sulfur) and 650 mAh/g capacity retention over 100 cycles were obtained with 50 wt% sulfur loading in the MC with 22nm pore size (4.8 cc/g). When the surface of MCS was coated with Clevios P to reduce the dissolve of polysulfide anions in electrolytes, it exhibits a high initial discharge capacity of ~1390 mAh/g and improved cycling stability with capacity retention of ~840 mAh/g over 100 cycles. The reported correlation among the structure, sulfur filling, surface modification and the electrochemical performance of the MCS composite cathodes provides guidance in designing new electrodes for lithium-sulfur batteries

25 ENERGY STORAGE↗

Preparation of Robust, Thin Zeolite Membrane Sheet for Molecular Separation

This paper reports a feasibility study on the preparation of zeolite membrane films on a thin, porous metal support sheet (50-{micro}m thick). Zeolite sodium A (NaA) and silicalite zeolite frameworks are chosen to represent synthesis of respective hydrophilic-type and hydrophobic-type zeolite membranes on this new support. It is found that a dense, continuous inter-grown zeolite crystal layer at a thickness less than 2 {micro}m can be directly deposited on such a support by using direct and secondary growth techniques. The resulting membrane shows excellent adhesion on the metal sheet. Molecular-sieving functions of the prepared membranes are characterized with ethanol/water separation, CO2 separation, and air dehumidification. The results show great potential to make flexible metal-foil-like zeolite membranes for a range of energy conversion and environmental applications.

36 MATERIALS SCIENCE↗

Poly(dimethylsiloxane) microchip-based immunoassay with multiple reaction zones: Toward on-chip multiplex detection platform

In this work, a poly(dimethylsiloxane) (PDMS) microchip-based immuno-sensing platform with integrated pneumatic micro valves is described. The microchip was fabricated with multiple layer soft lithography technology. By controlling the activation status of corresponding valves, reagent flows in the microchannel network can be well manipulated so that immuno-reactions only take place at designated reaction zones (DRZs). Four DRZs are included in the prototype microchip. Since these DRZs are all isolated from each other by micro valves, cross contamination is prevented. Using the inner surface of the all-PDMS microchannel as immunoassay substrate, on-chip sandwich format solid phase immunoassay was performed to demonstrate the feasibility of this immuno-sensing platform. Mouse IgG and fluorescein isothiocyanate (FITC) were used as the model analyte and the signal reporter respectively. Only 10 ul sample is needed for the assay and low detection limit of 5 ng/ml (≈33 pM) was achieved though low-cost polyclonal antibodies were used in our experiment for feasibility study only. The encouraging results from mouse IgG immunoassay proved the feasibility of our microchip design. With slight modification of the assay protocol, the same chip design can be used for multi-target detection and can provide a simple, cost-effective and integrated microchip solution for multiplex immunoassay applications.

60 APPLIED LIFE SCIENCES↗

Large Area Microcorrals and Cavity Formation on Cantilevers using a Focused Ion Beam

We utilize focused ion beam (FIB) to explore various sputtering parameters to form large area microcorrals and cavities on cantilevers. Microcorrals were rapidly created by modifying ion beam blur and overlaps. Modification in FIB sputtering parameters affects the periodicity and shape of corral microstructure. Cantilever deflections show ion beam amorphization effects as a function of sputtered area and cantilever base cavities with or without side walls. The FIB sputtering parameters address a method for rapid creation of a cantilever tensiometer with integrated fluid storage and delivery.

54 ENVIRONMENTAL SCIENCES↗

Imaging Chemical Aggregation of Ni/NiO Particles from Reduced NiO-YSZ

Energy dispersive X-ray spectroscopy (EDS) mapping of nickel oxide yttria-stabilized zirconia (NiO-YSZ) was carried out after various hydrogen reducing and methane steam reforming conditions. Nickel aggregation was visualized after methane steam reforming by correlating Ni K{sub {alpha}} map with scanning transmission electron microscopy (STEM) images. From the reduced O K{sub {alpha}} intensities in the Ni K{sub {alpha}} dominated regions after methane steam reforming, NiO reduction in to Ni can be interpreted. From correlation between Zr K{sub {alpha}} and O K{sub {alpha}} maps, high stability of YSZ was also realized. Examples of NiO-YSZ overlapped particles are considered to discuss chemical imaging of a single particle.

03 NATURAL GAS↗

Realization of Critical Distance during the Interplay between Re-deposition and Secondary sputtering from Milling of Angular Side Wall with a Focused Ion Beam

In-situ observation of critical distance (CD), a distance where secondary sputtering effects diminish and re-deposition starts to dominate is realized during controlled focused ion beam (FIB) sputtering. The experiments were performed on representative high density Nialloy and lower density porous Ni-YSZ. For the Ni-alloy case, it was observed that linear extrapolation of re-deposited layer width coincides with CD suggesting uniform sputtering and re-deposition effects. Estimation related to percentage of re-deposition from FIB etched layer at an angle of 50 degrees between the lower membrane and FIB etched side wall clearly demonstrated dominant secondary etching, neutralizing sputtering/redeposition and dominant re-deposition regions. Although the angle between FIB etched angular side wall and re-deposited/etched membrane adds some complication, the suggested overall experimental approach would substantially simplify to develop more realistic models than previously considered complex situations dealing with interplay between the re-deposition and secondary etching.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

BIOSYNGAS TO ALCOHOL CATALYST IMPROVEMENT PROJECT

Biofuels have garnered a high level of recent attention as a replacement for petroleum-based liquid transportation fuels and to potentially mitigate the effects of anthropogenic global warming. Ethanol is a biofuel that has found wide application as a blendstock to petroleum-based gasoline. Currently, ethanol is produced by the fermentation of sugars, which limits the feedstocks to crops such as corn and sugarcane. Alternatively, mixed alcohols, including ethanol and longer chain alcohols suitable as gasoline blendstocks or stand-alone fuels, could be produced thermochemically via a multi-step process that could utilize a large variety of biomass feedstocks, including non-edible feeds. MoS2-based catalysts are being developed by Range Fuels, Inc., who have built a thermochemical biomass-to-syngas-to-alcohol fuels demonstration facility in Soperton, Georgia. Due to changing market conditions over the last several years, the performance and costs of the catalyst initially chosen for use in this demonstration unit have since been found to be inadequate. Range Fuels enlisted the help of PNNL to use its expertise in catalyst characterization and computational modeling to help improve the performance of its catalyst with the goal of bringing the catalyst and, thus, the overall demonstration to a commercially viable state. This report describes PNNL’s characterization and modeling work and presents recommendations for improved catalyst synthesis.

alcohol↗

In Situ Transmission Electron Microscopy Observation of Microstructure and Phase Evolution in a SnO2 Nanowire during Lithium Intercalation

This paper reports development of a lithium-ion battery nanostructure device using a single nanowire for in-stu TEM study of the battery. This prototype lithium ion battery was built using a single SnO₂ nanowire as the anode, an air stable salt: lithium bis(trifluoromethansulfonyl) imide (LiTFSI) in a hydrophobic ionic liquid: 1-butyl-1-methylpyrrolidium TFSI (P14TFSI) as the electrolyte, and LiCoO₂ as the cathode. The microstructure evolution of the single nanowire anode was studied using TEM imaging, electron diffraction, and electron energy-loss spectroscopy during the operation of the battery. It has been observed that during initial charging, the electrolyte was found to decompose and subsequently be electrodeposited on the anode, leading to the formation of a coating layer on the anode. This coating layer was enriched with Li. Formation of this layer will retard the Li intercalation of SnO₂. This in situ TEM observation provides direct evidence that accounts for the observed low capacity and fast fading of the Li battery when LiTFSI-P14TFSI is used as the electrolyte.

74 ATOMIC AND MOLECULAR PHYSICS↗

Chromium Grain-boundary Segregation and Effect of Ion Beam Cleaning on Fe-Ni-Cr Alloys

The grain boundaries play important role to control the mechanical strength of ternary alloys. From spacecrafts to naval vessels to nuclear reactors, stress corrosion cracking, brittleness, oxidation mostly originates at the grain boundaries and cause long term structural stability problems in most of the metallic structures [1]. Fe-Ni-Cr based ternary metal alloys have been widely studied for more than fifty years [2, 3]. Despite of vast amount of research, chromium diffusion in stainless steel or other Ni-Fe-Cr based ternary alloys is still an open scientific problem with challenges in structural stability and corrosion resistance [4]. Particularly, austenite Fe-Ni-Cr is looked upon favorably in space and jet engine industry for their improved resistance to stress corrosion cracking [5]. In solid oxide fuel cells (SOFC), Ni-alloys are frequently used as interconnects and seals [6]. In this communication, simultaneous energy dispersive spectroscopy (EDS) and electron backscatter diffraction (EBSD) mapping is utilized to study chemical and structural aspects of chromium segregation in Fe-Ni-Cr alloy. A focused Ga-ion beam is also utilized to study the effect of ion beam cleaning on EBSD image quality (IQ) and inverse pole figure (IPF) maps of Fe-Ni-Cr alloy.

30 DIRECT ENERGY CONVERSION↗

Design of graphene sheets-supported Pt catalyst layer in PEM fuel cells

A series of cathodes using Pt supported onto graphene sheets with different contents of carbon black in the catalyst layer were prepared and characterized. Carbon black was added as a spacer between two-dimensional graphene sheets in the catalyst layer to study its effect on the performances of proton exchange membrane fuel cell. Electrochemical properties and surface morphology of the cathodes with and without carbon black were characterized using cyclic voltammetry, ac-impedance spectroscopy, electrochemical polarization technique, and scanning electron microscopy. The results indicated that carbon black effectively modifies the array of graphene supports, resulting in more Pt nanoparticles available for electrochemical reaction and better mass transport in the catalyst layer.

30 DIRECT ENERGY CONVERSION↗

SURFACE SEGREGATION STUDIES OF SOFC CATHODES: COMBINING SOFT X-RAYS AND ELECTROCHEMICAL IMPEDENCE SPECTROSCOPY

A system to grow heteroepitaxial thin-films of solid oxide fuel cell (SOFC) cathodes on single crystal substrates was developed. The cathode composition investigated was 20% strontium-doped lanthanum manganite (LSM) grown by pulsed laser deposition (PLD) on single crystal (111) yttria-stabilized zirconia (YSZ) substrates. By combining electrochemical impedance spectroscopy (EIS) with x-ray photoemission spectroscopy (XPS) and x-ray absorption spectroscopy XAS measurements, we conclude that electrically driven cation migration away from the two-phase gas-cathode interface results in improved electrochemical performance. Our results provide support to the premise that the removal of surface passivating phases containing Sr2+ and Mn2+, which readily form at elevated temperatures even in O2 atmospheric pressures, is responsible for the improved cathodic performance upon application of a bias.

30 DIRECT ENERGY CONVERSION↗

Determination of Electric-Field, Magnetic-Field, and Electric-Current Distributions of Infrared Optical Antennas: A Near-Field Optical Vector Network Analyzer

In addition to the electric field E(r), the associated magnetic field H(r) and current density J(r) characterize any electromagnetic device, providing insight into antenna coupling and mutual impedance. We demonstrate the optical analogue of the radio frequency vector network analyzer implemented in interferometric homodyne scattering-type scanning near-field optical microscopy (s-SNOM) for obtaining E(r), H(r), and J(r). The approach is generally applicable and demonstrated for the case of a linear coupled-dipole antenna in the midinfrared. The determination of the underlying 3D vector electric near-field distribution E(r) with nanometer spatial resolution and full phase and amplitude information is enabled by the design of probe tips with selectivity with respect to Ek and E? fabricated by focused ion-beam milling and nano-CVD.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗