Search NASA⌕ Search

Engineering topics

Sarah L Langston

Publications and source records attributed to Sarah L Langston.

13 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2023

X-59 Sonic Boom Test Results from the NASA Glenn 8- by 6-Foot Supersonic Wind Tunnel

A wind tunnel test was conducted to investigate near-field sonic boom pressure signatures of the X-59 Low-Boom Flight Demonstrator aircraft. A 1.62%-scale model of the aircraft was fabricated for the wind tunnel test, which took place in the NASA Glenn 8- by 6-Foot Supersonic Wind Tunnel in September and October 2021. The model had provisions for being mounted by a swept blade strut that attached at top of model ahead of the inlet, or by a rear-entry sting that held the model at the location of the nacelle. The model had alternate parts for ±0.5° deflections of the flaps, ailerons, and stabilator, and ±1° deflections of the T-tail. Off-body static pressure measurements of the flow field below the model were made on a pressure rail which had 420 orifices along its tip. The model was positioned at various heights from the rail by vertical movement of the tunnel strut, and at various longitudinal stations relative to the rail by means of a linear actuator mounted between the wind tunnel strut and the balance. Spatial averaging of model pressure signatures acquired over a range of longitudinal positions reduced the effects of tunnel flow distortions and the interference of the rail flow field and shocks on the model pressure signatures. The test was run at approximate Mach numbers of 1.36, 1.4, and 1.47, and the model was set at various angles of attack and roll relative to the rail. Plots of the model signatures for representative variations of Mach number, model angles, control deflections, and height relative to the rail are provided throughout the report. Repeatability was generally very good and gave confidence in the quality of the measurements. The signatures measured at various heights from the rail provided insight into the aging of the model shocks as they propagated from 1.2 to 3 body lengths from the model. Off-track signatures up to 45° from centerline obtained by rolling the model gave indications of the shock flow fields across the width of the sonic boom carpet. The deflections of the various control surfaces allowed assessment of the boom sensitivity to the control surface movements.

Sonic boom↗
NASA NTRS2023

Experimental Characterization of the Space Launch System Block 1B Liftoff and Transition Environment

A wind tunnel test was conducted at the NASA Langley Research Center 14- by 22-Foot Subsonic Tunnel to evaluate the liftoff and transition flow environment of the Space Launch System Block 1B launch vehicles and tower interference effects with the newly designed Mobile Launcher 2. This test leveraged several unique diagnostic capabilities, including eight distributed force and moment measurements on the launch tower tiers, new umbilical and crew access arm configurations, and unsteady pressure acquisition on the rocket nose in the cargo configuration. The tower loading revealed a strong impact of the SLS vehicle height on force coefficients for individual tiers. Although the umbilicals produced weak influence on the loading on both vehicle and launch tower, unsteady pressure measurements revealed a slight increase in fundamental pressure oscillation frequency at specific wind azimuth directions. Multimodal flow states were observed in the gap flow between the vehicle and solid rocket boosters, producing different load profiles along the vehicle that are now incorporated in the vehicle database. This phenomenon was investigated using time-series measurements of forces as well as tufts and smoke flow visualization.

Lee J Mears↗
NASA NTRS2023

Experimental Characterization of the Space Launch System Block 1B Liftoff and Transition Environment

A wind tunnel test was conducted at the NASA Langley Research Center 14- by 22-Foot Subsonic Tunnel to evaluate the liftoff and transition flow environment of the Space Launch System Block 1B launch vehicles and tower interference effects with the newly designed Mobile Launcher 2. This test leveraged several unique diagnostic capabilities, including eight distributed force and moment measurements on the launch tower tiers, new umbilical and crew access arm configurations, and unsteady pressure acquisition on the rocket nose in the cargo configuration. The tower loading revealed a strong impact of the SLS vehicle height on force coefficients for individual tiers. Although the umbilicals produced weak influence on the loading on both vehicle and launch tower, unsteady pressure measurements revealed a slight increase in fundamental pressure oscillation frequency at specific wind azimuth directions. Multimodal flow states were observed in the gap flow between the vehicle and solid rocket boosters, producing different load profiles along the vehicle that are now incorporated in the vehicle database. This phenomenon was investigated using time-series measurements of forces as well as tufts and smoke flow visualization.

SLS↗
NASA NTRS2021

Investigation of High Variability in the Creep Behavior of Vectran Yarn

Inflatable structures are being pursued as candidates for long-term habitats in space and on the surfaces of the Moon and Mars. Many concepts by the National Aeronautics and Space Administration and industry utilize high-strength, low-weight softgoods materials, such as Vectran, as the primary load-bearing structure in inflatable habitats. Understanding the creep behavior of these materials at the yarn level, is a critical part of understanding the component and module level creep behavior that allows the design and safe use of these habitats for long duration missions. In this paper, details of two different test methods to capture the creep-rupture behavior of Vectran yarn will be documented. One method utilizes load amplification via lever-arms, while the other method utilizes a more conventional direct loading approach. The two methods are compared to determine the best forward path for the research.

Soft goods↗
NASA NTRS2020

Recent NASA Wind Tunnel Free-Flight Testing of a Multirotor Unmanned Aircraft System Vehicle

Wind tunnel free-flight tests of a small quadrotor vehicle were completed in the NASA Langley 12-Foot Low Speed Tunnel and 20-Foot Vertical Spin Tunnel. The primary objective of these tests was to acquire flight data in forward and descending flight for the purpose of assessing the fidelity of an all-attitude flight dynamics simulation previously developed from static and dynamic wind tunnel data. A secondary objective was to demonstrate and mature free-flight test methods specific to the emerging class of small unmanned aircraft and urban air mobility vehicles. Experimental flight data correlated well with simulation predictions which included steady trim conditions consistent with straight and level flight and quasi-steady conditions associated with descent velocities prone to vortex ring state development. The test method was shown to be well suited to these classes of vehicles and several unique infrastructure requirements, including tether systems and data acquisition requirements were identified. In addition, unique operational test techniques and safety procedures were developed to accommodate the testing. Results of these tests will be used to support air traffic management studies and research into safety assurance concepts that enable the integration of these classes of vehicles into the National Airspace System.

John V Foster↗
NASA NTRSDate not supplied

Improved Techniques for Measuring Static Ground Wind Loads on the NASA Space Launch System Mobile Launcher 2

Vertical distribution of static ground wind loads was directly measured on Mobile Launcher ground support hardware to the NASA Space Launch System (SLS) at 1.75% scale in the Langley Research Center 14- by 22-Foot Subsonic Tunnel. Low-speed wind tunnel testing in the liftoff phase of flight was conducted for the SLS Block 1B family of rockets with their associated ground support systems. Improved methods for measuring and estimating static ground wind loads on the launch tower assembly are introduced in detail. A novel, distributed loads measurement technique is introduced and compared against lower-fidelity, previously utilized methods.

Ground Wind Loads↗
NASA NTRSDate not supplied

Overview of the High Reynolds Number Ascent Wind Tunnel Test of the Space Launch System at the National Transonic Facility

Transonic, high Reynolds number wind tunnel testing for the Space Launch System (SLS) ascent flight environment was conducted in the National Transonic Facility (NTF) at the NASA Langley Research Center from December 2019 to April 2021. The test was sponsored by the SLS Program and the NASA Engineering & Safety Center with the ob- jective of assessing and characterizing Reynolds number effects on the ascent aerodynamics of the SLS launch vehicle. The cryogenic test article was a 1.75%-scale representation of the SLS Block 1 Cargo configuration that was fabricated mostly out of stainless steel, but with several additive-manufactured components including the Solid Rocket Booster (SRB) attach brackets and the SRB nozzles. This was the first use of additive manufacturing on structural components of a cryogenic model in the NTF, therefore post-fabrication material testing and inspections were performed to satisfy safety requirements. Force & moment and surface pressure data were acquired for Mach numbers between 0.50 and 0.95 over a range of Reynolds numbers based on core stage diameter between 2x10^6 and a maximum of 40x10^6 corresponding to 45% of flight Reynolds number. Additionally, flow visualization data using Pressure Sensitive Paint were acquired with a focus on the SRB forward attach area, which is susceptible to Reynolds number sensitivity at transonic speeds. This pa- per provides an overview of the test campaign including details on the unique test article and the experimental setup and test execution. General test findings and observations are also presented, but the majority of the test results and data analyses are provided in a companion paper.

Space Launch System↗
NASA NTRSDate not supplied

Force and Moment Analysis for the High Reynolds Number Wind Tunnel Test of the Space Launch System at Ascent Conditions

A high Reynolds number test of the Space Launch System was performed at the NASA Langley National Transonic Facility (NTF). The objective of the test was to use the cryogenic testing capabilities of the NTF to acquire data over the largest range of Reynolds numbers possible with a specific focus on the Reynolds numbers closest to flight conditions. The test was performed at Mach numbers from 0.50 to 0.95 which corresponds to the ascent portion of flight for the SLS vehicle. Force and moment data showed that pitching and yawing moment were sensitive to Reynolds number effects over the full range of Mach and Reynolds numbers tested. Axial force also showed sensitivity to Reynolds number with the largest differences seen between Mach 0.50 to 0.90. Surface pressure data showed the highest sensitivity to Reynolds number in the vicinity of the solid rocket booster forward attach region.

Space Launch System↗
NASA NTRSDate not supplied

Reynolds Number Effects on a 5.2%-Scale High Lift Common Research Model

A 5.2%-scale High Lift Common Research Model (CRM-HL) semispan wind tunnel model was tested at the National Transonic Facility (NTF) wind tunnel in Hampton, VA. One of the primary objectives of the NTF test was to determine the effect of varying Reynolds number on the configuration. The test used a combination of air and cryogenic nitrogen testing to obtain up to flight-like Reynolds numbers. The landing and takeoff configurations of the model were tested at speeds ranging from Mach 0.2 to 0.35. The Reynolds numbers based on the mean aerodynamic chord of the model ranged from 1.6 to 30 million. Overall, the lift increased and drag decreased with increasing Reynolds number for chord Reynolds numbers less than 16 million, following well-established trends. However, some anomalies in the force and moment data were observed in the linear region of the angle of attack range that did not follow expected trends. The force and moment results for both the landing and takeoff configurations are presented, along with surface pressure data for the landing configuration. Incremental effects from the landing gear, nacelle, and horizontal tail on the landing configuration are also presented.

CRM-HL↗
NASA NTRSDate not supplied

High Reynolds Number Testing of the NATO AVT-298 SWiFT Configuration at the National Transonic Facility

A high Reynolds number wind tunnel test of the NATO AVT-298 Swept Wing Flow Test (SWiFT) configuration was conducted in the National Transonic Facility at the NASA Langley Research Center during the summer of 2023. The SWiFT research model geometry has relevance to both blended/hybrid wing body (BWB/HWB) and unmanned combat aerial vehicle (UCAV) configurations, and the test campaign was the culmination of an international collaboration under the NATO AVT-298 research task group. The main objectives of the test were to investigate Reynolds number scaling effects on low-speed stability & control characteristics and to examine the onset and progression of flow separation on the wings particularly near the wing crank. Force & moment and surface pressure data were acquired at Mach numbers from 0.2 to 0.8, Reynolds numbers from 2.5 to 34 million, angles of attack from -3 to 20 degrees, and sideslip angles from -10 to 10 degrees. Boundary layer transition detection techniques utilizing static pressure taps, unsteady pressure transducers, and sublimating chemicals were used on the model in a free/natural transition state or a forced transition state using trip dots. Pressure sensitive paint was used to obtain a global surface pressure profile on the model and an advanced laser velocimetry technique was used to obtain velocity measurements in the wake downstream of the wing crank. The results from the test showed clear Reynolds number scaling effects on the maximum lift coefficient and pitching moment coefficient at Mach 0.2, while also capturing significant hysteresis effects. The data acquired from the test will ultimately help improve computational aerodynamic analysis and design tools for application to future BWB-type vehicle configurations.

NATO AVT-298↗
NASA NTRSDate not supplied

Surface Pressure Results for the NATO AVT-298 SWiFT Configuration in the National Transonic Facility

A high Reynolds number wind tunnel test of the Swept Wing Flow Test (SWiFT) configuration was conducted in the National Transonic Facility at the NASA Langley Research Center during the summer of 2023. The test campaign was the culmination of an international collaboration under the NATO AVT-298 research task group. The main objective of the test was to investigate Reynolds number scaling effects on the low-speed stability & control characteristics of the SWiFT model. Surface pressure results corroborate the force & moment results and help to provide more insight into the observed flow behavior. The effect of angle of attack and Reynolds number on the low-speed surface pressure results are analyzed particularly around the leading edge of the model. The onset and progression of flow separation on the wings particularly near the wing crank is also investigated, as well as the cause of an observed double-stall behavior. Finally, the transonic results showed a slight forward movement of the shock location with decreased shock strength as Reynolds number was increased. The data acquired from the test will ultimately help improve computational aerodynamic analysis and design tools for application to future BWB-type vehicle configurations.

NATO AVT-298↗
NASA NTRSDate not supplied

Reynolds Number Effects on a 5.2%-Scale High Lift Common Research Model

A 5.2%-scale High Lift Common Research Model (CRM-HL) semispan wind tunnel model was tested at the National Transonic Facility (NTF) wind tunnel in Hampton, VA. One of the primary objectives of the NTF test was to determine the effect of varying Reynolds number on the configuration. The test used a combination of air and cryogenic nitrogen testing to obtain up to flight-like Reynolds numbers. The landing and takeoff configurations of the model were tested at speeds ranging from Mach 0.2 to 0.35. The Reynolds numbers based on the mean aerodynamic chord of the model ranged from 1.6 to 30 million. Overall, the lift increased and drag decreased with increasing Reynolds number for chord Reynolds numbers less than 16 million, following well-established trends. However, some anomalies in the force and moment data were observed in the linear region of the angle of attack range that did not follow expected trends. The force and moment results for both the landing and takeoff configurations are presented, along with surface pressure data for the landing configuration. Incremental effects from the landing gear, nacelle, and horizontal tail on the landing configuration are also presented.

CRM-HL↗