Search NASA⌕ Search

Engineering topics

Sarnello, Erik

Publications and source records attributed to Sarnello, Erik.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Monitoring Structural and Electronic Changes of Supported Metal Catalysts Using Combined X‐Ray Techniques

Supported metal nanoparticle catalysts have become increasingly crucial for many catalytic applications. However, long-term catalyst stability remains a problem due to catalyst deactivation caused by coke formation and sintering. The deposition of a thin overcoating via atomic layer deposition (ALD) onto metal-supported nanoparticles has shown to greatly inhibit catalyst deactivation. This work utilizes a model catalyst system comprised of Pt nanoparticles supported on Al 2 O 3 to demonstrate the effect of an atomically thin overcoating on supported metal nanoparticles. Continuous operando small-angle X-ray scattering (SAXS) and X-ray absorption near edge spectroscopy (XANES) monitor structural and electronic changes to the catalyst and overcoating during calcination. SAXS data fitting reveals the formation of nanopores in the overcoating at high temperatures, while XANES monitors the oxidation state of the Pt catalyst. Herein, the usefulness of combined X-ray techniques is demonstrated to characterize supported metal catalysts to further understanding of the synergistic effects of the ALD overcoating to aid in the design of new catalyst materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Softening by charging: how collective modes of ionic association in concentrated redoxmer/electrolyte solutions define the structural and dynamic properties in different states of charge

Understanding the physical and chemical processes occurring in concentrated electrolyte solutions is required to achieve redox flow batteries with high energy density. Highly concentrated electrolyte solutions are often studied in which collective crowded interactions between molecules and ions become predominant. In this work, experimental and computational methods were used to examine non-aqueous electrolyte solutions in two different states of charge as a function of redoxmer concentration. As the latter increases and the ionic association strengthens, the electric conductivity passes through a maximum and the solution increasingly gels, which is seen through a rapid non-linear increase in viscosity. We establish that the structural rigidity of ionic networks is closely connected with this loss of fluidity and show that charging generally yields softer ionic assemblies with weaker attractive forces and improved dynamical properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Direct measurement of Stokes–Einstein diffusion of Cowpea mosaic virus with 19 µs-resolved XPCS

Brownian motion of Cowpea mosaic virus (CPMV) in water was measured using small-angle X-ray photon correlation spectroscopy (SA-XPCS) at 19.2 µs time resolution. It was found that the decorrelation time τ(Q) = 1/DQ 2 up to Q = 0.091 nm -1 . The hydrodynamic radius R H determined from XPCS using Stokes–Einstein diffusion D = kT/(6πηR H ) is 43% larger than the geometric radius R 0 determined from SAXS in the 0.007 M K 3 PO 4 buffer solution, whereas it is 80% larger for CPMV in 0.5 M NaCl and 104% larger in 0.5 M (NH 4 ) 2 SO 4 , a possible effect of aggregation as well as slight variation of the structures of the capsid resulting from the salt–protein interactions.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2022

Ammonia-Assisted Light Alkane Anti-coke Reforming on Isolated ReO x Sites in Zeolite

The conventional reforming produces H 2 with stoichiometric amounts of CO and CO 2 from hydrocarbons. Here, we show that CO x -free H 2 can be produced from ammonia-assisted reforming (ammoreforming) of natural gas liquids (C n H 2n+2 + nNH 3 = nHCN + (2n + 1) H 2 , n = 2 or 3) at the same conditions as the steam reforming. Such a process co-produces HCN, which can be easily separated from H 2 and used as value-added chemicals or for NH 3 recycling through hydrolysis. In addition, the ammoreforming of ethane and propane was realized over the Re-modified HZSM-5 zeolite rather than the traditional Pt-based catalyst for the BMA process (methane ammoreforming). The specific activity of the Re/HZSM-5 catalysts at 650 °C is up to 1 mol H2 /g Re /min (or 180 min –1 ) during ethane ammoreforming. The catalyst is highly coke resistant and shows only slight deactivation with a time-on-stream up to 20 h. Characterization of the fresh and used catalysts by X-ray absorption and Raman spectroscopies suggested that the isolated ReO x site grafted by AlO 4 – tetrahedral in the zeolite framework is responsible for the outstanding catalytic activity and coke resistibility.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Catalytic Light Alkanes Conversion through Anaerobic Ammodehydrogenation

Catalytic transformation of light alkanes could have considerable practical value, yet remains one of the most challenging areas in catalysis research due to the inertness of the C–H bond. Here, we proposed an efficient ammodehydrogenation (ADeH) catalytic system for the direct C–N linkage between light alkanes and ammonia for CH 3 CN and H 2 (CO x free) production. This breakthrough is achieved over bifunctional metal-modified HZSM-5 catalysts, through the tandem dehydrogenation–amination–dehydrogenation mechanism. We show that ethane ADeH over the Pt/HZSM-5 catalyst can be realized under atmospheric pressure at temperatures as low as 350 °C. The specific rate of CH 3 CN is ~60 μmol/(g min), and the selectivity is up to 99% under such mild conditions. The yield of CH 3 CN increases with increasing temperature; however, the selectivity decreases due to the formation of HCN, C 2 H 4 , and CH 4 . Additionally, the Pt/HZSM-5 catalyst is coke-resistant during the ADeH owing to the strong interaction between NH 3 and the acid sites of the catalyst. So, we anticipate that the proposed ADeH could be extended for the transformation of various n/iso-alkanes with tunable selectivity to alkene and nitriles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Synthesis and Advanced Characterization of Polymer–Protein Core–Shell Nanoparticles

Enzyme immobilization techniques are widely researched due to their wide range of applications. Polymer–protein core–shell nanoparticles (CSNPs) have emerged as a promising technique for enzyme/protein immobilization via a self-assembly process. Based on the desired application, different sizes and distribution of the polymer–protein CSNPs may be required. This work systematically studies the assembly process of poly(4-vinyl pyridine) and bovine serum albumin CSNPs. Average particle size was controlled by varying the concentrations of each reagent. Particle size and size distributions were monitored by dynamic light scattering, ultra-small-angle X-ray scattering, small-angle X-ray scattering and transmission electron microscopy. Results showed a wide range of CSNPs could be assembled ranging from an average radius as small as 52.3 nm, to particles above 1 µm by adjusting reagent concentrations. In situ X-ray scattering techniques monitored particle assembly as a function of time showing the initial particle growth followed by a decrease in particle size as they reach equilibrium. The results outline a general strategy that can be applied to other CSNP systems to better control particle size and distribution for various applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Crowded electrolytes containing redoxmers in different states of charge: Solution structure, properties, and fundamental limits on energy density

Nonaqueous redox flow batteries use liquid electrolytes containing redox-active organic molecules (redoxmers) as their energy storage medium. To maximize energy density, the redoxmer concentration needs to be maximized while maintaining low viscosity and high ionic conductivity. During charge, a redoxmer molecule pairs with an ion in the electrolyte while another ion migrates across the membrane to maintain electric neutrality. In a crowded electrolyte, this reconstitution changes physical and chemical properties of the solution. To explore these behaviors, a phenothiazine redoxmer fully miscible with acetonitrile was used, and electrochemical charge was mimicked by chemical oxidation. The solutions were examined using small-angle X-ray scattering, nuclear magnetic resonance, and conductometry and modeled using classical molecular dynamics. Overall, our study indicates that physical and structural properties of redoxmer solutions in both states of charge make it exceedingly difficult to increase the redoxmer concentrations over 2 M at any temperature without compromising dynamic properties of such solutions. The cause for this limitation is proximity to a gel-like regime in which fluidity, diffusivity, and ionic conductivity exponentially decrease with increasing concentration. This tendency is compounded by non-Arrhenius behavior of the electrolyte: a small increase in the concentration outruns gains in fluidity and conductivity at a higher temperature. Thus the properties of crowded electrolytes generally make it impossible to operate when gel-like behavior sets in. Pushing the redoxmer concentration to 2.5-3 M might be possible for small redoxmer molecules, but it would require the use of ionic liquid electrolytes at 340-360 K. (C) 2021 Elsevier B.V. All rights reserved.

25 ENERGY STORAGE↗
DOE OSTI2021

Enhancing the performance of lithium oxygen batteries through combining redox mediating salts with a lithium protecting salt

Li–O 2 batteries have recently emerged to meet nowadays elevated electric energy demands. Redox mediators (RMs) for solution-inducing decomposition of discharge products are one approach to increase energy efficiency and reduce high overpotentials in these batteries. However, multiple obstacles hinder their usage such as redox shuttling, capacity fading, electrolyte degradation, etc. Herein, we present a new chemistry based on a combination of LiNO 3 , TEGDME and an ionic liquid that enables LiI (1 M) to lower the charge potential (3.5V) with a long cycle life of 270 cycles. 0.1 M LiI increases the cyclability up to 500 with a slightly increased charge potential (~4V) for a fixed capacity of 1000 mAh/g. Up to 100 cycles, this battery system retained ~95% Li 2 O 2 capacity with a ~0.8 V charge-discharge polarization gap. The addition of LiNO 3 to the electrolyte provides a protective solid electrolyte interface (SEI) on anode that works in synergy with the LiI RM. Moreover, we found that this electrolyte blend results in domain formation of ionic and neutral species enhancing the discharge and charge processes. Finally, DFT calculations provide a better understanding of the role of the anode SEI layer and the Li 2 O 2 decomposition promoted by the LiI during charge on the cathode.

25 ENERGY STORAGE↗
DOE OSTI2021

Controlling Infrared Plasmon Resonances in Inverse-Spinel Cadmium Stannate Nanocrystals via Site-Selective Cation-Exchange Reactions

Doped metal oxide nanocrystals (NCs) exhibit tunable localized surface plasmon resonances (LSPRs) in the infrared spectral region. Compared to the binary oxides commonly studied, plasmonic NCs derived from ternary oxides remain far less explored primarily due to the difficulty of controlling NC phase-purity and stoichiometry. Here, we report the synthesis of inverse spinel-type cadmium stannate (Cd 2 SnO 4 ) NCs, for which cation-exchange reactions were developed to tailor their composition and LSPR properties. X-ray absorption spectroscopy studies revealed that the inequivalent tetrahedrally and octahedrally coordinated Cd 2+ can be selectively exchanged for Cu + and In 3+ ions, respectively, enabling broadband tunable LSPR and Cu-mediated cation-exchange with lanthanide ions that are otherwise difficult to incorporate. Here, our work paves the way for systematic compositional engineering to accelerate the design of complex metal oxide NCs with emerging plasmonic, electronic, and magnetic properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Design and Characterization of ALD-Based Overcoats for Supported Metal Nanoparticle Catalysts

Supported metal nanoparticle (SMN) catalysts are enormously crucial for many catalytic applications. However, catalyst deactivation, caused by sintering and coke formation, is a ubiquitous problem that significantly undermines catalytic processing economics. The application of material overcoating onto supported metal nanoparticles by atomic layer deposition (ALD) offers the solution to inhibit catalyst deactivation. Herein, we discuss examples in which ALD has been used to stabilize SMN catalysts in gaseous and aqueous-phase reactions. We highlight the ALD tools and methods in coating high-surface-area catalysts. Besides, various techniques are introduced to understand better how to characterize the overcoating layer and the catalyst itself. Finally, the outlook for new techniques to characterize the ALD overcoated catalytic materials is discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Microscopic Understanding of the Ionic Networks of “Water-in-Salt” Electrolytes

“Water-in-salt” electrolytes with excellent electrochemical and physical properties have been extensively investigated. However, the structural understanding of the lithium bis(trifluoromethane sulfonyl)imide (LiTFSI) in water is still lacking. Here, we perform synchrotron X-ray scattering to systemically study the structural variation of TFSI anions in an aqueous solution under a variety of concentrations and temperatures. There are two different solvation structures in the solution: TFSI - solvated structure and TFSI - network. As the concentration increases, the TFSI - solvated structure gradually disappears while the TFSI - network gradually forms. Even at relatively low concentrations, the TFSI - network can be observed. Our experimental results show that these two structures can coexist at a particular concentration, and temperature changes will lead to one structure’s formation or disappearance. Also, the TFSI - network is the key to obtain a stable electrochemical window under relatively high temperatures.

Liu, Xinyi↗
DOE OSTI2020

Restorable Neutralization of Poly(acrylic acid) Binders toward Balanced Processing Properties and Cycling Performance for Silicon Anodes in Lithium-Ion Batteries

Neutralization of poly(acrylic acid) (PAA)-based binders using lithium hydroxide is a common strategy for fabricating silicon anode laminates, which improves rheological properties of slurries toward high-quality electrode laminates. However, the significantly increased basicity causes degradation of Si particles while the irreversible conversion of carboxylic acid groups to lithium carboxylates undermines the binding strength, collectively leading to adverse cycling performance of the fabricated Si anodes. Herein, a novel neutralization process for PAA binders is developed. A weak base, ammonia (NH 3 ), was discovered as a neutralizing agent that still promotes rheological response of binder solutions but results in a reduced pH increase. Interestingly, the resulting ammonium carboxylate groups may cleave during the drying process to restore the neutralized PAA (PAA-NH 3 ) binders to their pristine states. The best-performing composition of 50% neutralization (PAA-50%NH 3 ) provides comparable rheological response as a PAA-Li binder as well as much improved cycling performance. Additionally, the half-cells using the PAA-50%NH 3 binder can deliver 60% capacity retention over 100 cycles at C/3 rate, affording a 23.8% increase compared to PAA-Li half-cells. This restorable neutralization process of PAA binders represents an innovative strategy of mitigating issues from slurry processing of Si particles to achieve concurrent improvements in high-quality lamination and cycling performance.

25 ENERGY STORAGE↗
DOE OSTI2020

An Ion-Imprinting Derived Strategy to Synthesize Single-Atom Iron Electrocatalysts for Oxygen Reduction

Carbon-based single-atom catalysts (CSACs) have recently received extensive attention in catalysis research. However, the preparation process of CSACs involves a high-temperature treatment, during which metal atoms are mobile and aggregated into nanoparticles, detrimental to the catalytic performance. Herein, an ion-imprinting derived strategy is proposed to synthesize CSACs, in which isolated metal-nitrogen-carbon (Me-N 4 -C x ) moiety covalently binds oxygen atoms in Si-based molecular sieve frameworks. Such a feature makes Me-N 4 -C x moiety well protected/confined during the heat treatment, resulting in the final material enriched with single-atom metal active sites. As a proof of concept, a single-atom Fe-N-C catalyst is synthesized by using this ion-imprinting derived strategy. Finally, experimental results and theoretical calculations demonstrate high concentration of single FeN 4 active sites distributed in this catalyst, resulting in an outstanding oxygen reduction reaction (ORR) performance with a half-wave potential of 0.908 V in alkaline media.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Self-Assembled Solute Networks in Crowded Electrolyte Solutions and Nanoconfinement of Charged Redoxmer Molecules

Redoxmers are electrochemically active organic molecules storing charge and energy in electrolyte fluids circulating through redox flow batteries (RFBs). Such molecules typically have solvent-repelling cores and solvent-attracting pendant groups introduced to increase solubility in liquid electrolytes. These two features can facilitate nanoscale aggregation of the redoxmer molecules in crowded solutions. In some cases, this aggregation leads to the emergence of continuous networks of solute molecules in contact, and the solution becomes microscopically heterogeneous. In this study, we used small-angle X-ray scattering (SAXS) and molecular dynamics modeling to demonstrate formation of such networks and examine structural factors controlling this self-assembly. We also show that salt ions become excluded from these solute aggregates into small pockets of electrolytes, where these ions strongly associate. This confinement by exclusion is also likely to occur to charged redoxmer molecules in a “sea” of neutral precursors coexisting in the same solution. Here, we demonstrate that the decay lifetime of the confined charged molecules in such solutions can increase several fold compared to dilute solutions. We attribute this behavior to a “microreactor effect” on reverse reactions of the confined species during their decomposition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Pore-Edge Tailoring of Single-Atom Iron–Nitrogen Sites on Graphene for Enhanced CO 2 Reduction

Hosting atomically dispersed nitrogen-coordinated iron sites (Fe-N 4 ) on graphene offers unique opportunities for driving electrochemical CO 2 reduction reaction (CO 2 RR) to CO. However, the strong adsorption of *CO on the Fe-N 4 site embedded in intact graphene limits current density due to slow CO desorption process. Herein, we report how the manipulation of pore edges on graphene alters the local electronic structure of isolated Fe-N 4 sites and improves their intrinsic reactivity for prompting CO generation. We demonstrate that constructing holes on graphene basal plane to support Fe-N 4 can significantly enhance its CO 2 RR compared to the pore-deficient graphene-supported counterpart, exhibiting a CO Faradaic efficiency of 94% and a turnover frequency of 1630 h -1 at 0.58 V vs RHE. Mechanistic studies reveal that the incorporation of pore edges results in the downshifting of the d-band center of Fe sites, which weakens the strength of the Fe-C bond when the *CO intermediate adsorbs on edge-hosted Fe-N 4 , thus boosting the CO desorption and evolution rates. These findings suggest that engineering local support structure renders a way to design high-performance single-atom catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗