Search NASA⌕ Search

Engineering topics

Satcher, J. H.

Publications and source records attributed to Satcher, J. H..

6 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2014

Bright x-ray sources from laser irradiation of foams with high concentration of Ti

Low-density foams irradiated by a 20 kJ laser at the Omega laser facility (Laboratory for Laser Energetics, Rochester, NY, USA) are shown to convert more than 5% of the laser energy into 4.6 to 6.0 keV x rays. This record efficiency with foam targets is due to novel fabrication techniques based on atomic-layer-deposition of Ti atoms on an aerogel scaffold. A Ti concentration of 33 at. % was obtained in a foam with a total density of 5 mg/cm{sup 3}. The dynamics of the ionization front through these foams were investigated at the 1 kJ laser of the Gekko XII facility (Institute for Laser Engineering, Osaka, Japan). Hydrodynamic simulations can reproduce the average electron temperature but fail to predict accurately the heat front velocity in the foam. This discrepancy is shown to be unrelated to the possible water adsorbed in the foam but could be attributed to effects of the foam micro-structure.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2013

Comparison and analysis of zinc and cobalt-based systems as catalytic entities for the hydration of carbon dioxide

In nature, the zinc metalloenzyme carbonic anhydrase II (CAII) efficiently catalyzes the conversion of carbon dioxide (CO 2 ) to bicarbonate under physiological conditions. Efforts have been directed towards the development of small molecule mimetics that can facilitate this process and thus have a beneficial environmental impact, but these efforts have met very limited success. Herein, we undertook quantum mechanical calculations of four mimetics, 1,5,9-triazacyclododedacane, 1,4,7,10-tetraazacyclododedacane, tris(4,5-dimethyl-2-imidazolyl)phosphine, and tris(2-benzimidazolylmethyl)amine, in their complexed form either with the Zn 2+ or the Co 2+ ion and studied their reaction coordinate for CO 2 hydration. These calculations demonstrated that the ability of the complex to maintain a tetrahedral geometry and bind bicarbonate in a unidentate manner were vital for the hydration reaction to proceed favorably. Moreover, these calculations show that the catalytic activity of the examined zinc complexes was insensitive to coordination states for zinc, while coordination states above four were found to have an unfavorable effect on product release for the cobalt counterparts.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2012

Efficient laser-induced 6-8 keV x-ray production from iron oxide aerogel and foil-lined cavity targets

The performance of new iron-based laser-driven x-ray sources has been tested at the OMEGA laser facility for production of x rays in the 6.5-8.5 keV range. Two types of targets were experimentally investigated: low-density iron oxide aerogels (density 6-16 mg/cm{sup 3}) and stainless steel foil-lined cavity targets (steel thickness 1-5 {mu}m). The targets were irradiated by 40 beams of the OMEGA laser (500 J/beam, 1 ns pulse, wavelength 351 nm). All targets showed good coupling with the laser, with <5% of the incident laser light backscattered by the resulting plasma in all cases (typically <2.5%). The aerogel targets produced T{sub e}=2 to 3 keV, n{sub e}=0.12-0.2 critical density plasmas yielding a 40%-60% laser-to-x-ray total conversion efficiency (CE) (1.2%-3% in the Fe K-shell range). The foil cavity targets produced T{sub e}{approx} 2 keV, n{sub e}{approx} 0.15 critical density plasmas yielding a 60%-75% conversion efficiency (1.6%-2.2% in the Fe K-shell range). Time-resolved images illustrate that the volumetric heating of low-density aerogels allow them to emit a higher K-shell x-ray yield even though they contain fewer Fe atoms. However, their challenging fabrication process leads to a larger shot-to-shot variation than cavity targets.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2010

Fusion Application Targets

Complex target structures are necessary to take full advantage of the unique laboratory environment created by inertial confinement fusion experiments. For example, uses-ofignition targets that contain a thin layer of a low density nanoporous material inside a spherical ablator shell allow placing dopants in direct contact with the DT fuel. The ideal foam for this application is a low-density hydrocarbon foam that is strong enough to survive wetting with cryogenic hydrogen, and low enough in density (density less than ~30 mg/cc) to not reduce the yield of the target. Here, we discuss the fabrication foamlined uses-of-ignition targets, and the development of low-density foams that can be used for this application.

36 MATERIALS SCIENCE↗
NASA NTRS2008

Development of Improved Aerogels for Spacecraft Hypervelocity Capture

The highly successful NASA Discovery mission Stardust became the first mission to return samples to Earth from a known comet in January 2006 [1]. The samples were captured during a flyby of comet 81P/Wild2 using aerogel, a very low density, silica (SiO2)-based solid with a highly porous structure [2]. Currently, scientists around the world are studying the cometary particles returned by Stardust and reporting fascinating discoveries about the history of comets and the evolution of our solar system. Given the widely acknowledged success of the Stardust mission, additional comet sample return missions are attractive and competitive concepts for future NASA Discovery-class missions; in particular, additional comet sample return missions will allow the first laboratory studies to investigate the naturally occurring diversity among comets, a crucial scientific question for understanding not just the formation of comets but also the very nature of the early solar system. Though Stardust was highly successful, there are important lessons learned from the mission on which advances in aerogel technology can be based

Lisse, C. M.↗