Search NASA⌕ Search

Engineering topics

Sater, B. L.

Publications and source records attributed to Sater, B. L..

14 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Optimization of silicon 8 cm x 8 cm wrapthrough Space Station cells for 'on orbit' operation

The optimization of Space Station cells for on-orbit performance is described. Design trades were performed in which back DAR coating thickness was traded against thermal absorptance and performance under front and back (albedo) illumination. Typical examples of modeled cell performance under different scenarios are given. Experimental illuminated output data under back illumination for specific DAR coating thicknesses are also given. Computer modeling of the solar array using TRASYS and SINDA programs also provide on-orbit thermal data and performance predictions. The overall backside response from albedo illumination was found to make a considerable contribution to the total array performance, particularly during the early stages of space station assembly when the arrays are feathered.

Lillington, D. R.↗
NASA NTRS1981

Method of cold welding using ion beam technology

A method for cold welding metal joints is described. In order to remove the contamination layer on the surface of the metal, an ion beam generator is used in a vacuum environment. A gas, such as xenon or argon, is ionized and accelerated toward the metal surface. The beam of gas effectively sputters away the surface oxides and contamination layer so that clean underlying metal is exposed in the area to be welded. The use of this method allows cold welding with minimal deformation. Both similar and dissimilar metals can be cold welded with this method.

Sater, B. L.↗
NASA NTRS1977

A first order theory of the p/+/-n-n/+/ edge-illuminated silicon solar cell at very high injection levels

A first order theory of the edge-illuminated p(+)-n-n(+) silicon solar cell under very high injection levels has been derived. The very high injection level illuminated J-V characteristic is derived for any general base width to diffusion length (W/L) ratio and it includes the minority carrier reflection by the n-n(+) high-low junction. The beneficial effects of the high-low junction are shown to be significant until extremely high injection levels are reached. The theoretical dependencies of Jsc and Voc on temperature, incident intensity, and base resistivity are derived and discussed in detail. Some experimental results are given and these are discussed in relation to the theory.

Goradia, C.↗
NASA NTRS1975

The high intensity solar cell - Key to low cost photovoltaic power

This paper discusses the problems associated with conventional solar cells at high intensities and presents the design considerations and performance characteristics of the 'high intensity' (HI) solar cell which appears to eliminate the major problems. Test data obtained at greater than 250 AM1 suns gave a peak output power density of 2 W per sq cm at an efficiency exceeding 6% with an unoptimized cell operating at over 100 C. It appears that operation at 1000 AM1 suns at efficiencies greater than 10% is possible. At 1000 AM1 suns and 10% efficiency, the HI cell manufacturing cost is estimated to be $0.25/watt, with multi-megawatt annual production capability already existing within the industrial sector. A high intensity solar system was also analyzed to determine its cost effectiveness and to assess the benefits of further improving HI cell efficiency.

Sater, B. L.↗
NASA NTRS1975

The high intensity solar cell: Key to low cost photovoltaic power

The design considerations and performance characteristics of the 'high intensity' (HI) solar cell are presented. A high intensity solar system was analyzed to determine its cost effectiveness and to assess the benefits of further improving HI cell efficiency. It is shown that residential sized systems can be produced at less than $1000/kW peak electric power. Due to their superior high intensity performance characteristics compared to the conventional and VMJ cells, HI cells and light concentrators may be the key to low cost photovoltaic power.

Sater, B. L.↗
NASA NTRS1974

High voltage solid-state relay

Hybrid microelectronics relay has characteristics significantly superior to conventional solid state relays. Relay provides 2500 Vdc input to output isolation and operates from high threshold logic signal to switch load of 400 Vdc at 2 mA. Technology should be of interest to manufacturers of discrete components.

Sater, B. L.↗
NASA NTRS1974

A miniature high voltage plasma interaction flight experiment - Project MINX

A miniature high-voltage array was fabricated, incorporating the multi-junction edge illuminated (MJC) cell technique. The array consists of 32 2x2.2 cm MJCs, series connected, capable of 1600 V open circuit at 1 AMO and 1.2 mA short circuit. A solid state, high-voltage relay is connected across each 4-cell subgroup of the array. It was built to test plasma current drain on space systems using high voltage as might occur when a high-voltage solar array is operated from low to synchronous orbit.

Riley, T. J.↗
NASA NTRS1974

The multiple junction edge illuminated solar cell

The multiple junction edge illuminated solar cell (M-J Cell) was devised for high voltage, low current applications. Devices to be flight-tested in early 1974 with 96 series-connected PNN+ junctions in a 2 cm x 2.3 cm size deliver 36 volts at 1 milliampere. Test data of M-J Cells fabricated with resistivities of 10, 50, 100, 200, 450, and 1000 ohm-cm silicon are presented and problem areas are discussed. An additional potential application of the M-J Cell lies in utilization of its high-intensity performance that has been demonstrated at levels in excess of 100 AMO suns.

Sater, B. L.↗
NASA NTRS1973

The advantages of the high voltage solar array for electric propulsion

The high voltage solar array (HVSA) offers improvements in efficiency, weight, and reliability for the electric propulsion power system. The basic HVSA technology involves designing the solar array to deliver power in the form required by the ion thruster. This paper delves into conventional power processes and problems associated with ion thruster operation using SERT II experience for examples. In this light, the advantages of the HVSA concept for electric propulsion are presented. Tests conducted operating the SERT II thruster system in conjunction with HVSA are discussed. Thruster operation was observed to be normal and in some respects improved.

Sater, B. L.↗
NASA NTRS1973

Development of a hybrid microelectronics solid state relay for 2500 volts isolation and minus 120 C to 80 C thermal cycling range

A hybrid microelectronics solid state relay was developed in a TO-116 package for the MINX project. The relay provides 2500 Vdc input to output isolation and operated from a MHTL logic signal to switch a load of 400 Vdc at 2 mA. The relay is designed to operate in space and survive 1000 thermal cycles of 120 C to 80 C. The use of X-rays for failure analysis in small hybrid circuits proved valuable and the applications of vacuum deposited Parylene as a dielectric coating proved extremely valuable.

Sater, B. L.↗
NASA NTRS1973

The advantages of the high voltage solar array for electric propulsion

The high voltage solar array offers improvements in efficiency, weight, and reliability for the electric propulsion power system. Conventional power processes and problems associated with ion thruster operation using SERT 2 experience are discussed and the advantages of the HVSA concept for electric propulsion are presented. Tests conducted operating the SERT 2 thruster system in conjunction with HVSA are reported. Thruster operation was observed to be normal and in some respects improved.

Sater, B. L.↗