Engineering topics

Saunders, Alison M.

Publications and source records attributed to Saunders, Alison M..

3 records

DOE OSTI2024

Solid face sheets enable lattice metamaterials to withstand high-amplitude impulsive loading without yielding

Owing to their ability to provide tunable mechanical responses, lattice materials are frequently studied to elucidate their response to static and dynamic loads. However, these roles are typically in opposition: static loads must be supported sufficiently far away from the onset of buckling or yielding, whereas dynamic loads are typically ameliorated by crushing of the lattice, which provides excellent energy-absorption due to the large plastic deformation accompanying densification. In contrast, this work considers the octet truss as an exemplar topology, in a structural role where it must simultaneously support static loads while enduring high-amplitude impulsive loads. This study focuses on the ability to withstand impulsive loads without yielding, an essential prerequisite to enduring dual loading. Computational studies using the ALE3D hydrocode were performed to examine the response of the octet truss under a short temporal width impulse shape associated with laser-driven shocks. A key finding was that covering the lattice with a solid face sheet and treating this face sheet thickness as a design variable allows the Taylor-like pulse to be attenuated prior to entering the weaker lattice, at the cost of added mass up front. Experimental validation was accomplished by laser-driven shock testing, using octet trusses printed out of Ti-5Al-5V-5Mo-3Cr. The results show that for a given quantity of mass, the attenuation is maximized when as much mass as possible is moved into the face sheet, leaving a more slender lattice structure. The effect of placing mass in the face sheet rather than lattice beams dominates the effect of relative density, to the point where a low-mass structure with most of the mass concentrated in the face sheet can outperform a high-mass structure with most of the mass in the lattice. Finally, by further understanding the propagation of short pulse width waves within under-dense structures, this study expand the domain of applicability of such structures, including lattice materials, to challenging dual-loading regimes spanning decades of strain rates.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Microstructure effects on high velocity microparticle impacts of copper

Constitutive models can fail to predict high-rate deformation behavior due to their inability to account for microstructural effects. In part, this is because of a dearth of experimental benchmarking data in the high strain-rate, low pressure regime, since many high-rate experiments also probe a region of strong shockwaves, at which point microstructure effects no longer play a primary role. This work uses laser-induced particle impact testing to quantitatively study high velocity impacts of small, rigid alumina microspheres on flat copper substrates with varying amounts of initial cold work in the weak shock regime, but at very high strain rates up to ~10 7 s –1 . Through paired experiments and numerical simulations, this work shows that the initial microstructure condition can have significant influence on dynamical mechanical properties in this range. Specifically, prior work hardening of the copper substrate leads to increased rebounding of the microparticles (i.e., less plastic dissipation in the impact) as well as smaller craters. Each of these experimental measurables can be converted into a strength measure, i.e., the dynamic yield strength or dynamic hardness, respectively, neither of which is well predicted consistently by existing constitutive laws. The general trend of hardening can be captured by such models by incorporating an existing “pre-strain,” suggesting that future calibration of the materials parameters may yield a good fit over a broader range of conditions. Our results emphasize the importance of reporting the microstructural condition in dynamic studies, as well as the necessity of accounting for these factors when formulating and optimizing constitutive models.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Interactions of laser-driven tin ejecta microjets over phase transition boundaries

Ejecta microjets offer an experimental methodology to study high-speed particle laden-flow interactions, as microjets consist of millions of particulates traveling at velocities of several kilometers per second and are easily generated by most common shock drives. Previous experiments on the OMEGA Extended Performance laser found that collisions between two counter-propagating laser-driven tin ejecta microjets varied as a function of drive pressure; jets generated near shock pressures of 10 GPa passed through each other without interacting, whereas jets generated at shock pressures of over 100 GPa interacted strongly, forming a cloud around the center interaction point. In this paper, we present a more systematic scan of tin ejecta microjet collisions over intermediate pressure regimes to identify how and at what shock pressure interaction behavior onsets. Radiographs of interacting microjets at five different laser drive energies qualitatively demonstrate that interaction behavior onsets slowly as a function of laser drive energy. Quantitative mass and density metrics from each radiograph provide trends on jet characteristics and collisional mass dispersion. It is observed that jetting mass, jet densities, and mass dispersion increase with increasing drive pressures and that the increased jet density at the higher drive energies may account for the increased mass dispersion. This work provides an important step in the understanding of tin ejecta microjet collisions and paves the way for future studies on the physics dominating high-speed particle-laden flow interactions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗